

Apply 3M™ Scotch-Weld 5313 (or an equivalent suitable black butyl strip) into
the cavity shown. Apply enough butyl to fill the cavity without the butyl covering
the top edges of the window seal and body panel.
Use a finger or thumb to firm down the butyl.
REWORK 2
8.



Inspect the NVH material already applied in the area shown.

Apply 3M™ Scotch-Weld 5313 (or an equivalent suitable black butyl strip)
to fill any cavities which may be present in the area shown.
Use a finger or thumb to firm down the butyl.
REWORK 3
9.



Mold a piece of 3M™ Scotch-Weld 5313 (or an equivalent suitable black butyl
strip) approximately 155 mm in length and 5 mm in width.

10.



Apply the butyl along the body panel seam, as shown in the illustration.
Use a finger or thumb to firm down the butyl.
REWORK 4
11.



Apply 3M™ Scotch-Weld 5313 (or an equivalent suitable black butyl strip)
around the wiring harness, as shown in the illustration. The butyl must fully seal
the hole within the body panel.
Use a finger or thumb to firm down the butyl.
REWORK 5

12.



Locate the NVH material already applied in the area shown.

13.



Apply 3M™ Scotch-Weld 5313 (or an equivalent suitable black butyl strip) to fill
the small cavity marked 'A' in the illustration, directly above the NVH material
already applied.

14.

Reverse steps 1 to 3.

15.

Complete steps 1 to 14 for the opposite side of the vehicle.

SERVICE INSTRUCTION 3

RANGE ROVER AND RANGE ROVER SPORT
NOTES:
Range Rover shown, Range Rover Sport is similar.
Some illustrations may vary depending on the vehicle specification, the
essential information is always correct.
Some components may have been removed from the vehicle to provide extra
clarity.

1.

Lower the front left window.

2.



Reposition the front door window seal, as shown in the illustration.

3.

WARNING:
Always follow the manufacturer's instructions.



Use SikaTack OEM+ (or an equivalent suitable polyurethane glazing adhesive)
to seal the front window seal.
1. Apply a suitable masking tape to the area shown in the illustration.
2. Apply a bead of sealant within the front window seal, as shown in the
illustration.
3. Apply a bead of sealant to the area shown in the illustration, making sure
to fill any cavities present.

4.

Reverse steps 1 to 3.
Remove any residue caused by the masking tape.

5.



Apply a suitable masking tape to the upper area of the front door, as shown in
the illustration.

6.

CAUTION:
The cut must be made in line with the front door glass.

NOTE:
If required, raise the window slightly to aid with this step.



Using a suitable tool, cut through the front door outer waist seal, as shown in the
illustration.
Remove the masking tape.
Remove any residue caused by the masking tape.

7.

Complete steps 1 to 6 for the opposite side of the vehicle.

SERVICE INSTRUCTION 4

RANGE ROVER ONLY
NOTES:
Some illustrations may vary depending on the vehicle specification, the
essential information is always correct.

Some components may have been removed from the vehicle to provide extra
clarity.

1.

Open the hood.

2.

Open the front left door.

3.



Remove the bolt.

4.

CAUTIONS:
Before removing the a-pillar molding, make sure the surrounding area
is clean and dry.
Before removing the a-pillar molding, make sure the a-pillar molding is
clean and dry.
Do not use tools during this operation, removal of the a-pillar molding
must be completed by hand.



Remove the a-pillar molding by pushing with both hands and sliding down.

5.



Remove and discard the NVH pad at the top of the a-pillar.
Clean the surrounding area.

6.



Install the new polyethylene closed-cell foam NVH pads at the top of the a-pillar.

7.



Place the a-pillar molding onto a suitable flat surface and locate the foam NVH
pad which is applied across the length of the a-pillar molding.

8.



Apply 3M™ Adhesive Tape - PX5011 (or an equivalent suitable double-sided
tape) on top of the foam NVH pad. Leave a minimum of 30 mm excess backing
exposed at the top of the a-pillar molding, as shown in the illustration.

9.



When completing step 9 below, make sure the 30 mm excess backing is
positioned as shown in the illustration. This will allow the backing to be removed
from the a-pillar molding after the a-pillar molding is installed.

10.

CAUTIONS:
Make sure the front edge to the windshield has a consistent gap and
that the air deflector is seated correctly.
Do not use tools during this operation, installation of the a-pillar
molding must be completed by hand.
Make sure all fixing tabs are correctly located.



Install the a-pillar molding by pushing with both hands and sliding up.

11.

CAUTION:
Make sure to pull downward when removing the backing from the
double-sided tape.



Carefully and very slowly, remove the backing from the double-sided tape.

12.



Install the bolt.
Torque: 1.3 Nm

13.

Close the front left door.

14.

Complete steps 2 to 13 for the opposite side of the vehicle.

15.

Close the hood.

SERVICE INSTRUCTION 5

RANGE ROVER ONLY
NOTES:
Some illustrations may vary depending on the vehicle specification, the
essential information is always correct.
Some components may have been removed from the vehicle to provide extra
clarity.

1.

Open the rear left door.

2.



Locate the rear quarter window seal.

3.



Apply a suitable masking tape to the rear quarter window seal. Make sure the
window seal can still be lifted.

4.

WARNING:
Always follow the manufacturer's instructions.



Using the aid of another technician, apply approximately 75 ml of SikaTack
OEM+ (or an equivalent suitable polyurethane glazing adhesive) along the
cavity behind the window seal.
1. NOTE:
Use a suitable trim tool to assist in lifting the window seal.

Insert the applicator at the top of the window seal and seal the hole in the
area marked 'A' in the illustration.
2. While applying the sealant, move the applicator downward behind the
window seal, to the bottom of the window seal.

5.



Use a finger or thumb to firm down the window seal.
Remove the masking tape.
Remove any residue caused by the masking tape.

6.

Close the rear left door.

7.

Complete steps 1 to 6 for the opposite side of the vehicle.