SERVICE BULLETIN
SB2415
ADDRESSEES

: Owners and operators
ABC Customer Care and Parts Source

VEHICLE MODEL

: CX35 with MVP instrument cluster

SYSTEM/SUBSYSTEM

: 05.10 Brakes – Compressed-air brakes

BULLETIN TYPE

: Service Information

DATE

: January 30th, 2024

SUBJECT

: Compressed-air brake system functional check

TERMS & CONDITIONS

: This service bulletin does not entitle to any reimbursement.

DESCRIPTION
These tests are designed to identify the cause(s) of a sluggish performance and/or leaks in the
system. The tests give you a general idea of the system condition. The procedures described in this
service bulletin are applicable to CX35 vehicles with a MVP instrument cluster
JOB QUALIFICATION
The task has to be carried out by a technician trained in the operations at hand. If you are not
sure that you’re qualified, contact ABC Customer Care.

EQUIPMENT CONDITION





Park the coach on a level-surfaced service pit.
Apply the parking brake and shut down the engine.
Put a “DO NOT OPERATE” tag on the instrument panel.
Read the entire procedure before starting to work.

WARNING!
Observe safe shop practices at all times.

SAFETY INFORMATION ABOUT SYSTEMS UNDER PRESSURE




Do not tighten or loosen pipe or hose connections while the pipe or hose is under pressure.
Do not check pressurized lines for leaks with your hands.
Safely depressurize devices containing compressed air under pressure before opening
them.

Continued on next page.
SB2415_USA_en_2024-01-30

Page 1 of 8

INDICATION OF COMPRESSED-AIR TANK PRESSURES ON INSTRUMENT
CLUSTER
After starting up the engine, actual values of the compressed-air level of all the axles appear
immediately on the instrument cluster.

Figure 1

PROCEDURE
Step
1
2
3
4
5
6
7
8

Action
Put chocks in front of and behind the front-axle wheels.
Prior to performing any test, check condition of all air lines. Check pipes for kinks or
dents, hoses for signs of wear or overheating.
Test the compressed-air supply system as explained in “STEP 3 IN DETAIL”.
Test the tank supply circuit for leakage as indicated in “STEP 4 IN DETAIL”.
Test the parking brake operation as indicated in “STEP 5 IN DETAIL”.
Test the service brake delivery circuits for leakage as indicated in “STEP 6 IN DETAIL”.
Test the one way check valves operation as indicated in “STEP 7 IN DETAIL”.
Test the operation of the dual air system as indicated in “STEP 8 IN DETAIL”.

End of procedure

Continued on next page.
SB2415_USA_en_2024-01-30

Page 2 of 8

STEP 3 IN DETAIL: To test compressed-air supply system (pressure build-up, low
pressure warning, governor operation)
Step
3.1
3.2

Action
Connect an accurate pressure gauge to the test fitting (identified by two red adhesive
tapes) behind the front bumper.

WARNING!
Use appropriate hearing protection while draining the air tanks.
Completely drain the entire air system by using the drain cocks on the air tanks.
Refer to figure 6 at the end of this service bulletin for air tanks location.

Figure 2: Compressed-air tank drain cock,
current model
Left: closed
Right: open

3.3
3.4

Close the air tanks cocks if the compressed-air system is drained.
Turn the vehicle ignition on.
Low air warning on dashboard display should appear and low air buzzer should
sound. If not so, check installation.

Figure 3: Low air warning on dashboard
display (example shows a low pressure
condition in circuit 1)

3.5

Start the engine and run at 1,600 rpm.
Low air warning should disappear and buzzer should stop when pressure reaches 80 psi.
If not so, check installation.

3.6

Start timing as system pressure reaches 85 psi and stop at 100 psi.
Air build-up time should be 45 seconds or less. If the build-up time is excessive,
check:
 for excessive air system leakage;
 for restrictions in the air compressor inlet or discharge lines (carbon build-up);
 Air compressor condition (excessive wear on piston rings and/or cylinders);
 operation of air compressor inlet and discharge valves.
Continued on next page.
SB2415_USA_en_2024-01-30

Page 3 of 8

3.7

Idle the engine. Observe reading on the air pressure gauge when governor cuts out
the compressor. The reading should be as indicated in table 1.
Table 1: Governor setting
Cut-in pressure (psi)
Cut-out pressure (psi)
115 +0/-5 psi
135 ± 5 psi

3.8

With the engine still running, slowly reduce air pressure in the system by applying
and releasing the brakes. Observe reading on pressure gauge when governor cuts in
the compressor. The reading should be as indicated in table 1. If not so, check the
operation of the governor and the unloading mechanism on the compressor.

STEP 4 IN DETAIL: To test tank supply circuit for leakage
Step
4.1
4.2
4.3
4.4

Action

Connect an accurate pressure gauge to the test fitting (identified by two red adhesive
tapes) behind the front bumper.
Fully charge the air system and stop the engine.
Allow pressure to stabilize for at least 1 minute.
Observe the pressure gauge for 2 minutes, and note any pressure drop.
Pressure drop should not be more than 3 psi per minute. If not so, coat all air line
connections and pneumatic components with a water and soap solution. Bubbles will
indicate an air leak, and none should be permissible. Repair or replace defective parts.

STEP 5 IN DETAIL: To test parking brake operation
Step
5.1
5.2
5.3

Action

Connect an accurate pressure gauge to the test fitting in the air line leading to the
spring brake part of the brake cylinder of the left-hand drive wheel.
Fully charge the air system and stop the engine.
Pull the parking brake button to apply the parking brake. The pressure gauge should
indicate no pressure.

Figure 4: Parking brake button

Continued on next page.
SB2415_USA_en_2024-01-30

Page 4 of 8

5.4

Push and hold the emergency parking brake release button to release the parking
brake. The pressure gauge should indicate pressure.

Figure 5: Emergency
parking brake release button

5.5
5.6
5.7

Release the emergency parking brake release button.
Push the parking brake button to release the parking brake. The pressure gauge
should indicate pressure.
Reduce air pressure in the system by applying and releasing the foot brake.
Low air warning on dashboard should appear and low air buzzer should sound when
pressure drops to 80 psi. Drive axle spring brakes should apply when pressure drops
to approximately 60 psi.

STEP 6 IN DETAIL: To test service brake delivery circuits for leakage
Step
6.1

6.2
6.3
6.4

Action

Connect accurate pressure gauges to:
 the test fitting in the air line leading to the brake cylinder of a front axle wheel;
 the test fitting in the air line leading to the service part of a brake cylinder of a
drive axle wheel.
Fully charge the air system and stop the engine.
Apply the foot brake pedal, allow pressure to stabilize for at least 1 minute.
Hold down the foot brake pedal for 2 minutes while observing the pressure gauge.
Pressure drop should not be more than 4 psi per minute. If not so, coat all brake air
line connections and pneumatic components with a water and soap solution. Bubbles
will indicate an air leak, and none should be permissible. Repair or replace defective
parts.

Continued on next page.
SB2415_USA_en_2024-01-30

Page 5 of 8

STEP 7 IN DETAIL: To test operation of one way check valves

WARNING!
Use appropriate hearing protection while draining the air tanks.
Step
7.1
7.2

7.3

Action

Fully charge the air system and stop the engine.
Drain the wet tank.
The indication of the compressed-air tank pressures on the instrument clusterl
should not indicate a loss of pressure.
Close the wet tank drain cock.

STEP 8 IN DETAIL: To test operation of dual air system

WARNING!
Use appropriate hearing protection while draining the air tanks.
Step
8.1

8.2
8.3
8.4
8.5
8.6
8.7
8.8
8.9
8.10
8.11
8.12

Action

Connect accurate pressure gauges to:
 the test fitting in the air line leading to the brake cylinder of a front axle wheel;
 the test fitting in the air line leading to the service part of a brake cylinder of a
drive axle wheel;
Fully charge the air system and stop the engine.
Drain the drive axle service brakes tank.
Make a service brake application and check whether the pressure gauge connected
to the front axle brakes indicate pressure.
Close the drain valve of the drive axle service brakes tank.
Start the engine and fully charge the air system again.
Stop the engine.
Drain the front axle brakes tank.
Make a service brake application and check whether the pressure gauge connected
to the drive axle brakes indicate pressure.
Close the drain valve of the front axle brakes tank.
Start the engine and fully charge the air system again.
Stop the engine.

Continued on next page.
SB2415_USA_en_2024-01-30

Page 6 of 8

LOCATION OF COMPRESSED-AIR TANKS

Figure 6: Location of compressed-air tank on CX35
1.
2.
3.
4.
5.
6.
7.
8.
9.

Kneeling system
Front axle brakes
Accessories
Rear raising
Parking brake emergency release
Drive axle service brakes
Air-dryer regeneration
Wet tank
ZF automated transmission (only on vehicles with ZF automated transmission)

Continued on next page.
SB2415_USA_en_2024-01-30

Page 7 of 8

HELP DESK:
Consult ABC Customer Care & Parts Source toll-free for guidance on 1-877-427-7278. Listen
for the prompts for warranty and select that option.

DISCLAIMER:
The procedures contained herein are not exclusive. Van Hool cannot possibly know, evaluate,
or advise the transportation industry of all conceivable ways in which a procedure may be
undertaken or of the possible consequences of each such procedure. Other procedures may be
as good, or better, depending upon the particular circumstances involved. Each carrier who
uses the procedures herein must first satisfy itself thoroughly that neither the safety of its
employees or agents, nor the safety or usefulness of any products, will be jeopardized by any
procedure selected.

INFORMATION HANDLING:
Important supplements to and modifications of technical information not yet included
in the manual, are communicated by means of Service Bulletins.

VAN HOOL CUSTOMER PORTAL:
Consult the customer portal regularly for the latest service documentation. Beside the
maintenance manual, you will also find the operating manual and the spare parts catalogue of
your vehicle on the customer portal. The customer portal is accessible through
www.vanhool.be, and only with a code (password) from Van Hool. If you do not have a
password yet, request it by using the link on the Van Hool website.

SB2415_USA_en_2024-01-30

Page 8 of 8