1/23/24, 2:53 PM

41 05 23_SERVICE ACTION: CHECKING THE GAPS ON THE TAILLAMPS

SIB 41 05 23
SERVICE ACTION: CHECKING THE GAPS ON THE TAILLAMPS

2024-01-22

Please perform the procedure outlined in this Service Information on all affected vehicles before customer
delivery. In the event the customer has already taken delivery of the vehicle, please perform the procedure
the next time the vehicle is in the shop.
☐

THIS REPAIR IS MOBILE FRIENDLY

MODEL
E-Series
U11

Model Description
X1 Sports Activity Vehicle

Production Date
August 2, 2022 – August 31, 2023

SITUATION
Contact between the taillamps and the
tailgate/side panel(s) can occur. This can
cause paint abrasion, and over time corrosion
can form on the body of the vehicle/tailgate.
Note: This can occur on either one or both
sides of the vehicle.

CORRECTION
Measure the gaps between the taillamps’ housing and the tailgate/side panels. If the gap is too small, the
taillamp(s) must be removed and the specific area of the tailgate/side panel(s) will need to be inspected for
corrosion.

PROCEDURE
Note: When it is necessary to perform a consequential paint finish repair (Paint pen or CCRC/Auto Body
Shop), it is mandatory to identify and record the area that required attention due to the issue described in
the Service Information Bulletin.
For example:
Chafe mark 1, or
Chafe marks 2, 3, or
Chafe marks 4, 5, 6
For these claim submissions, the applicable
condition identifier information described
above is to be provided in the technician’s RO
notes and in the claim comment section.
A. Measure the gap between the inner taillamps and the tailgate.

Copyright ©2024 BMW of North America, Inc.
about:blank

1/7

1/23/24, 2:53 PM

41 05 23_SERVICE ACTION: CHECKING THE GAPS ON THE TAILLAMPS

1. Inspect the inner taillamp(s) housing

on the tailgate for correct gap.

The gap is to be checked at the diagonal area
of the taillamps as shown in the photo.
Note: Check both inner taillamps’ gap.

Attempt to insert a small strip of writing paper
between the diagonal part of the taillamps
housing and tailgate.
If the paper CAN be inserted in the gap
between the inner taillamps housing and
tailgate, the taillamp(s) is OK.
If the paper CANNOT be inserted in the gap
between the inner taillamp(s) housing and
tailgate, continue to step 2.

2. Remove the inner taillamp(s) that is contacting the tailgate following the repair instructions listed in ISTA/AIR 63 21
279/281 and/or 63 21 285.

Copyright ©2024 BMW of North America, Inc.
about:blank

2/7

1/23/24, 2:53 PM

41 05 23_SERVICE ACTION: CHECKING THE GAPS ON THE TAILLAMPS

3. Clean off the tailgate paint using R2 cleaner.
Inspect for any paint abrasion. The critical area is
5mm inward from the top edge as shown in the
photo.

(A). If there is NO abrasion of the clear coat or the base color, or if there is only minor abrasion which dulls the
clear coat, NO paint touch-up is needed. Continue to step 5.
4.

(B). If the clear coat or base color is abraded so that the primer is visible: Touch up the area with the matching
touch-up paint stick. Continue to step 5 afterwards.
(C). If the paint is not only damaged/abraded but there is bubble formation under the paint (lifting) or even rust
formation, the damaged area must be repaired, and the entire tailgate repainted. After the repainting, continue to
step 5.
5. Apply a strip of the clear abrasion tape along
the edge pressing, between the transition of the
tailgate upper section to the lower section.

Position the tape so that it is 3mm inward
of the edge pressing. Once the tape is in
position, press along the tape surface fully
and firmly for maximum adhesion.

Extend the tape so that it is parallel to the
edge pressing, and that the lower end
wraps along the radius of the edge where
is changes horizonal.
Repeat steps 1-5 on the other inner
taillamp.

6. Install inner taillamps.

7. Check the outer taillamps in the areas
shown in the photo.

Copyright ©2024 BMW of North America, Inc.
about:blank

3/7

1/23/24, 2:53 PM

41 05 23_SERVICE ACTION: CHECKING THE GAPS ON THE TAILLAMPS

8. Check each indicated sections of the outer taillamp gaps to the side panels using the paper strip method as
performed in step 1.

9. The right side shown with the body partially
stripped for clarity. The specific areas to be
checked are in the red boxes as shown in the
photo.
If the paper CAN be inserted in the gap
between the outer taillamps housing and
the side panel(s), the taillamp is OK.
If the paper CANNOT be inserted in the
gap between the outer taillamps housing
and the side panel(s), continue to step 10.

10. Remove the outer taillamp(s) that is contacting the side panel(s) following the repair instructions listed in ISTA/AIR 63 21
275/277 and/or 63 21 283

11. Clean the side panel(s) paint where the outer taillamp sits using R2 cleaner. Inspect for any paint abrasion.

(A). If there is NO abrasion of the clear coat or the base color, or if there is only minor abrasion which dulls the clear
coat, no paint touch-up is needed.
(B). If the clear coat or base color is abraded so that the primer is visible: Touch up the area with the matching
touch-up paint stick. Continue to step 12.
(C). If the paint is not only damaged/abraded but there is bubble formation under the paint (lifting) or even rust
formation, the damaged area must be repaired, and the entire side panel repainted.
12. Install taillamp(s). Adjust the gap to the side panel to 1.1 mm.

PARTS INFORMATION
To determine the part number that applies to the specific vehicle being repaired, enter the VIN/chassis
number into either ETK or AIR, this will consider the specific equipment and/or options that are fitted to the
vehicle.
Part Number
41 00 9 644 448

Description
Adhesive film kit v (1 kit can repair 7 vehicles)

83 19 0 417 324

Cleanser R2 (500 ml)

Refer to ETK

Touch-up paint stick (aka paint pen, depending on the repair
performed, 1 stick can be used for multiple vehicles)

Quantity
1
Sublet as
needed
Sublet as
needed

CLAIM INFORMATION
Reimbursement for this Action will be via normal claim entry utilizing the applicable work package
information below, and when a Copyright
repair is required,
additional
associated
©2024 the
BMW
of North
America,work
Inc. flat rate labor operation
about:blank

4/7

1/23/24, 2:53 PM

41 05 23_SERVICE ACTION: CHECKING THE GAPS ON THE TAILLAMPS

codes, or when required, the corresponding third-party paint finish repair work in sublet.
Plusposition (+)

The vehicle is already in the workshop
The vehicle arrives for this Service Action, no other Main work will be
performed/claimed during this workshop visit

Main work

Below are the special flat rate labor operation code choices for this action. Only one Main work flat rate labor
operation code can be claimed per workshop visit.
Repair Code:

0041250200

U11 Checking gap dimension of rear lights (tailgate, side
panel) and reworking if necessary

Workshop Inspection – No Repair is Necessary
Work Pkg

Labor
Operation

#1

00 75 726

Check the gap dimension of all rear
lights (not in combination with follow- 3 FRU
up work)

00 75 188

Check the gap dimension of all rear
lights (not in combination with follow- 5 FRU
up work)

Description (Workshop)

Labor Allowance

Or:
#2
Or:
Workshop Inspection – Repair is Necessary (Attachment 1 or 2 as Applicable)
Work Pkg

#3

Labor
Operation

Description (Workshop)

00 75 727

Check the gap dimension of all rear
lights (always with follow-up work,
1 FRU
refer to the applicable attachment 1 or
2)

00 75 189

Check the gap dimension of all rear
lights (always with follow-up work,
3 FRU
refer to the applicable attachment 1 or
2)

Labor Allowance

Or:
#4

And with the above:
Attachment 1: Additional Work - Workshop Repair Complete
Please refer to the following attachment for the additional Associated Work (AW) repair procedures, Options
AW_A through AW_K as required, and for the corresponding special flat rate labor operation codes to select
and use for the claim submission.
B410523 Attachment 1 Workshop Repair Complete

Or:
Attachment 2: Additional Work - Consequential Third-Party Paint Finish Repair Work
Scopes
Copyright ©2024 BMW of North America, Inc.
about:blank

5/7

1/23/24, 2:53 PM

41 05 23_SERVICE ACTION: CHECKING THE GAPS ON THE TAILLAMPS

Please refer to the following attachment for the additional associated CCRC/Approved Auto Body Shop paint
finish repair work scopes, Options PW_A to PW_G as required.
B410523 Attachment 2 CCRC_Auto Body Shop Repair

Claim Repair Comments and Sublet Explanations
Please refer to the attachment (1 or 2) that applies to the repair performed.
Alternative Mobility Solution (AMS) for Vehicle Owners (RO and Claim Comments Required)
This Service Action repair qualifies for Alternative Mobility Solution (AMS) expense reimbursement, claim
this item under the Defect Code noted above as follows:
Sublet Code 2 - Itemize the AMS sublet amount on the repair order and in the claim comment section.

Please refer to SI B01 29 16 for additional information.

FEEDBACK REGARDING THIS BULLETIN
Technical Feedback
Warranty Feedback
Parts Feedback

To submit feedback for the technical topic of this bulletin: Submit your
feedback in the rating box at the top of this bulletin
To submit feedback for the CLAIMS section of this bulletin: Submit an IDS
ticket to the Warranty Department, or use the chat available in the
Warranty Documentation Portal
To submit feedback for the PARTS section of this bulletin: Submit an IDS
ticket to the Parts Department

Supporting Materials
picture_as_pdf B410523 Attachment 1 Workshop Repair Complete.pdf
picture_as_pdf B410523 Attachment 2 CCRC_Auto Body Shop Repair.pdf

Copyright ©2024 BMW of North America, Inc.
about:blank

6/7

1/23/24, 2:53 PM

41 05 23_SERVICE ACTION: CHECKING THE GAPS ON THE TAILLAMPS

Copyright ©2024 BMW of North America, Inc.
about:blank

7/7

B41 05 23 Attachment 1: WP 3/ 4 Associated Work Procedures A through K - Workshop Repair Only

January 2024

Select and claim the one (1) additional “Associated Work” (AW) repair procedure’s special labor operation codes below that
apply to the required repair.
(*) Note: “Additional work/rework (As applicable) with a paint pen” special labor operaton codes are claimed only when
the corresponding work procedures are required to be performed.

Wk Pkg

Labor Operation (1)

#3

00 75 727

Description (Workshop)
Check the gap dimension of all rear lights (always with
follow-up work) (Plusposition work)

Labor Allowance
1 FRU

Or:
#4

00 75 189

AW 2/3 Left Side Panel (LSP)
A
2/3 (LSP – 00 75 735)
B
2/3 (LSP – 00 75 735)
C
2/3 (LSP – 00 75 735)
D
2/3 (LSP – 00 75 735)
LO Count
Labor Operations
2

00 75 735

3

00 75 738

LO Count

Labor Operations

4

00 75 728

5

00 75 731

6

00 75 733

LO Count

Labor Operations

4

00 75 729

5

00 75 732

6

00 75 734

LO Count

Labor Operations

2

00 75 730

3

00 75 731

4

00 75 732

5

00 75 733

6

00 75 734

Check the gap dimension of all rear lights (always with
follow-up work) (Main work)
1 Left Tailgate (LTG)
4 Right Tailgate (RTG)

3 FRU
5/6 Right Side Panel (RSP)

1 (LTG – 00 75 728)
4 (RTG – 00 75 729)
1/4 (LTG/RTG – 00 75 730)
Description (WP 3 or 4 with Associated Work A)
Remove and install the rear light on the left side
panel/not in combination with painting the left side
panel
(*) Additional work/rework left side panel with a
paint pen/not in combination with painting the left side
panel
Description
(WP 3 or 4 with Associated Work B)
Remove and install the left tailgate rear light/not in
combination with painting the tailgate
Additional work/adhere the film to the tailgate, left
(*) Additional work/rework tailgate on the left with a
paint pen/not in combination with painting the tailgate
Description (WP 3 or 4 with Associated Work C)
Remove and install the right tailgate rear light/not in
combination with painting the tailgate
Additional work/adhere the film to the tailgate, right
(*) Additional work/rework tailgate on the right with a
paint pen/not in combination with painting the tailgate
Description (WP 3 or 4 with Associated Work D)
Remove and install the left and right tailgate rear
lights/not in combination with painting the tailgate
Additional work/adhere the film to the tailgate, left
Additional work/adhere the film to the tailgate, right
(*) Additional work/rework tailgate on the left with a
paint pen/not in combination with painting the tailgate
(*) Additional work/rework tailgate on the right with a
paint pen/not in combination with painting the tailgate

1

Labor Allowances
6 FRU
1 FRU
Labor Allowances
7 FRU
1 FRU
1 FRU
Labor Allowances
7 FRU
1 FRU
1 FRU
Labor Allowances
8 FRU
1 FRU
1 FRU
1 FRU
1 FRU

B41 05 23 Attachment 1: WP 3/ 4 Associated Work Procedures A through K - Workshop Repair Only

Wk Pkg