

Transmission is in Park.



All CONSULT VI cables are
securely connected.



All C-III plus updates are installed.



Select Home, and restart the
reprogram procedure from the
beginning.

EXAMPLE

99/118

Figure 196

NTB17-039Q

177. Follow the on-screen instructions to Erase All DTCs.

178. When the entire reprogramming process is complete, the screen in Figure 197 will
display.

179. Verify the before and after part numbers are different.

180. Print a copy of this screen (Figure 197) and attach it to the repair order for warranty
documentation.

181. Select Confirm.

31036 - _ _ _ _ _
31036 - _ _ _ _ _

TRANSMISSION

Figure 197

100/118

NTB17-039Q

182. Perform ADDITIONAL SERVICE WHEN REPLACING CONTROL VALVE.


Refer to TM – Transaxle & Transmission / RE0F10E / BASIC INSPECTION,
and perform ADDITIONAL SERVICE WHEN REPLACING CONTROL VALVE.



Erase all DTCs with C-III plus.

IMPORTANT: Check off these additional services as they are completed and attach
this to the repair order when finished.
CHECK OFF

ADDITIONAL SERVICE PROCEDURE
PRINT CURRENT CALIBRATION DATA
CHECK THE SERIAL NUMBER
WRITE THE DATA
PRINT NEW CALIBRATION DATA
FWD CLUTCH POINT LEARNING (Using procedure starting below)
PERFORM SELECT LEARNING (DRIVE/REVERSE LEARNING)
ERASE CVT FLUID DEGRADATION LEVEL DATA
ERASE ALL DTCS

183. Verify the CVT operates normally and no abnormal noises are heard during a test
drive.

FWD CLUTCH POINT LEARNING (using CONSULT-III plus)

184. Apply the vehicle’s parking brake.
185. Start the engine and warm up to operating temperature (50-100o C [122-212o F]).

186. Connect the CONSULT PC to the vehicle.

187. Start CONSULT-III plus (C-III plus).

101/118

NTB17-039Q

188. Wait for the plus VI to be recognized.


The serial number will display when the plus VI is recognized.

189. Select Diagnosis (One System).

Figure 198
190. Select Work Support under TRANSMISSION.

Figure 199

102/118

NTB17-039Q

IMPORTANT: The following FWD CLUTCH POINT LEARNING will be performed twice.
Once in drive (D) and once in reverse (R).

191. Select FWD CLUTCH POINT LEARNING and then Start.

Figure 200
192. With the engine still running and at idle, depress the brake pedal and shift the CVT
into neutral (N).


Confirm that all of the required conditions indicated in Figure 201 are being met.

193. Select Start.

Required
conditions

Figure 201
103/118

NTB17-039Q

194. While maintaining all conditions shown in Figure 201 and the “Current status”
indicates “EXECUTING”, shift the CVT into D and then wait until the “Current status”
indicates “COMPLETED”.
HINT: This may take up to three (3) minutes to complete.

Figure 202
195. When the screen in Figure 203 is displayed, select End.
196. Turn the engine OFF and then back ON.

Figure 203

104/118

NTB17-039Q

197. Select FWD CLUTCH POINT LEARNING and then Start.

Figure 204
198. With the engine still running and at idle, depress the brake pedal and shift the CVT
into neutral (N).


Confirm that all of the conditions indicated in Figure 205 are being met.

199. Select Start.

Required
conditions

Figure 205

105/118

NTB17-039Q

200. While maintaining all conditions shown in Figure 205 and the Current status indicates
“EXECUTING”, shift the CVT into R and then wait until the Current status indicates
COMPLETED.
HINT: This may take up to 3 minutes to complete.

Figure 206
201. When the screen in Figure 207 is displayed, select End.

Figure 207

106/118

NTB17-039Q

TROUBLESHOOTING
The Dummy Cover Will Not Sit Flush
Clutch pack
seated correctly

If the dummy cover does not sit flush, the
clutch pack may not be fully seated.


Figure 208 shows clutch pack fully
seated.



Clutch pack is not fully seated if it is
not below the surface that the
dummy cover bolts to.



Use instructions below to fully seat
clutch pack.

Surface dummy
cover seats on

HINT: Always handle the clutch pack by
the input shaft.

Figure 208

Dummy cover

202. Remove the dummy cover.

Figure 209
O-ring removed
Clutch pack
203. Pull up the clutch pack by the input
shaft to remove the entire clutch pack.


Make sure the O-ring is not
installed at this time, or it could be
damaged during reassembly.

Input shaft

Figure 210

107/118

NTB17-039Q

Clutch pack

Clutch pack layers
204. Using an appropriate tool, gently align
the layers of the clutch pack.


Bottom of the clutch pack shown in
Figure 211.

Appropriate
tool
Align layers
Figure 211

205. Reinsert the entire clutch pack while
holding the input shaft.
206. Gently jiggle the input shaft until the
clutch pack seats below case lip.
Input shaft
207. If the clutch pack does not seat, rotate
back and forth from the input shaft and
jiggle.
Clutch pack

208. If the clutch pack still does not seat,
repeat from step 203.

Figure 212

108/118

NTB17-039Q

PARTS INFORMATION

SUB-ASSEMBLY REPAIR
HINT: Refer to the following pages for single use parts that are not included in the
kits below for Quest. All other models should refer to the Library in the EPC for the
Single Use Parts List.

(1)
(2)
(3)

(4)
(5)
(6)

DESCRIPTION

PART #

QUANTITY

KIT-PULLEY (1)

See Table D, below

1

CONTROL VALVE KIT (2)

3170E-29X9C

1

Loctite 5460 Sealant (3) (4)

999MP-LT5460P

(5) (6)

See the ALL REPAIRS table on page 111 for additional required parts.
Includes QR label, CD-R, and control valve assembly.
Loctite 5460 Sealant can be ordered through the Nissan Maintenance Advantage
program: Phone: 877-NIS-NMA1 (877-647-6621) or Website: Order via link on dealer
portal www.NNAnet.com and click on the “Maintenance Advantage” link.
For warranty repairs, Loctite 5460 Sealant must be used. For customer pay repairs,
Loctite 5460 Sealant or its equivalents are recommended.
One container of Loctite 5460 Sealant is good for approximately 5 repairs. Sealant
is not included in the kits.
Bill out Loctite 5460 Sealant (or equivalent) under expense code 008. Do not include
the Loctite 5460 Sealant part number on the claim.

Table D
DESCRIPTION

MODEL
Pathfinder

KIT-PULLEY

MODEL YEAR

PART NUMBER

2013-2014

31214-29X7C

2015-2020

31214-29X9B

Altima
(6 Cylinder)

2013-2014

31214-29X7A

2015-2018

31214-29X8A

Maxima

2016-2022

31214-29X8B

Murano

2015-2022

31214-29X9A

Quest

2015-2017

31214-29X9A

****Single use parts that are not included in the KIT-PULLEY****
Altima, Maxima, Murano, and Pathfinder:
Refer to the Library in the EPC for the Single Use Parts Lists.
Quest
See the Table on the next page.

109/118

NTB17-039Q

SUB-ASSEMBLY REPAIR - CONTINUED
****Single use parts that are not included in the kits on page 107****
2015-2017 Quest
DESCRIPTION

PART # PREFIX

QUANTITY

PACKING/SEAL (Radiator drain plug O-ring)
SEAL - O RING
(Steering high pressure line O-ring to pump)
CLAMP (CVT fluid cooler hose clamps)

21481

1

49745

1

21639

2

15208

1

11026

1

21304

1

20691

2

20695

1

01223

3

NUT (Lower strut nuts)

54588

4

PIN - COTTER (Axle Cotter pin)
NUT - LOCK, FRONT WHEEL BEARING
(Wheel hub lock nut)
SEAL - O RING
(Steering high pressure line O-ring to steering gear)
NUT
(Mounting nut b/w transverse link and front
suspension member)
NUT (Engine mounting insulator [RH] upper nuts)

40073

2

40262

2

49745

1

54588

4

11258

3

SEAL - O RING (Fill-tube O-ring)

31084

1

CLAMP (CVT water hose clamps)

16439

2

GASKET (CVT drain plug gasket)

11026

1

SEAL - O RING (O-ring: CVT fluid overflow plug)

31526-3VX0B

1

OIL FILTER ASSY (Engine oil filter)
WASHER - DRAIN PLUG
(Engine oil drain plug washer)
RING - RUBBER (Engine oil cooler O-ring)
GASKET - EXHAUST
(Exhaust ring gaskets to catalyst)
BEARING - SEAL, EX
(Exhaust seal bearing to center exhaust)
NUT (Exhaust nuts to catalyst B1)

110/118

NTB17-039Q

CONTROL VALVE REPLACEMENT

(1)

DESCRIPTION

PART #

QUANTITY

CONTROL VALVE KIT (1)

3170E-29X9C

1

See the ALL REPAIRS table below for additional required parts.

****Single use parts that are not included in the above kit****
DESCRIPTION

PART # PREFIX

QUANTITY

CLAMP (CVT fluid cooler hose clamps)

21639

2

GASKET (CVT drain plug gasket)
Pathfinder ONLY
O-Ring (External CVT cooler O-rings)

11026

1

22180-9NB0A

2

DESCRIPTION

PART #

QUANTITY

Transmission Cooler Cleaner

999MP-AM006P

As needed

Nissan NS-3 CVT Fluid (1) (2)

999MP-NS300P

As needed

Lens Swab packet (3)

J-51963

As needed

ALL REPAIRS

(1) Nissan NS-3 CVT Fluid can be ordered through the Nissan Maintenance Advantage
program: Phone: 877-NIS-NMA1 (877-647-6621) or Website: Order via link on dealer