12/4/23, 6:48 PM

11 07 23_VOLUNTARY EMISSION RECALL 23E-A05: REPLACE SWITCHABLE ROCKER ARM

SIB 11 07 23
VOLUNTARY EMISSION RECALL 23E-A05: REPLACE SWITCHABLE
ROCKER ARM
☐

2023-11-28

THIS REPAIR IS MOBILE FRIENDLY

Please perform the procedure outlined in this Service Information on all affected vehicles before customer
delivery. In the event the customer has already taken delivery of the vehicle, please perform the procedure
the next time the vehicle is in the shop.
This Service Information Bulletin (Revision 4) replaces SI B11 07 23 dated October 2023.
What’s New:

Procedure updated
Parts list updated
Claim Information section updated

MODEL
E-Series
G05
G06
G07
G70

Model Description
X5 Sports Activity Vehicle
X6 Sports Activity Coupe
X7 Sports Activity Vehicle
7 Series Sedan

Production Date
May 8, 2023 – June 17, 2023
May 8, 2023 – June 17, 2023
May 9, 2023 – June 14, 2023
April 19, 2023 – June 20, 2023

AFFECTED VEHICLES
Vehicles which require this campaign to be completed will show it as “Open” when checked either in AIR, AWP, Campaign
Summary, or Warranty Vehicle Inquiry.
Please make sure you check your dealer inventory as soon as possible. You can see a list of affected vehicles in
Inventory Campaign Details (ICD) under ROSS.

SITUATION
The return springs on the exhaust camshaft followers may break.

PROCEDURE
Read this entire Bulletin before starting any repairs.
Check the vehicle history for engine or cylinder head replacement. If the engine or cylinder has been
replaced, then the campaign can be cleared. Refer to the Claim Information section.
If the vehicle history does not show any of the above repairs, replace the exhaust camshaft followers. Refer
to Repair Instruction 11 33 055 “Remove and install/replace switchable cam follower on the exhaust side.”
The steps to remove and install the cylinder head cover may be missing from Repair Instruction 11 33 055. If
so, refer Repair Instruction 11 12 001 Replace Cylinder Head cover for the additional information.
Important ISTA Repair Instruction Supplements:
1. The current repair instructions may state to remove the engine assembly from the vehicle, this is an inaccurate instruction
step. Proceed to the steps for removing the cylinder head cover while the engine is still in the vehicle. Do not remove the
engine from the vehicle to perform any repairs described in this Service Information Bulletin.

Copyright ©2023 BMW of North America, Inc.
about:blank

1/8

12/4/23, 6:48 PM

11 07 23_VOLUNTARY EMISSION RECALL 23E-A05: REPLACE SWITCHABLE ROCKER ARM

2. The current repair instructions may also state to replace the VANOS gears. Disregard. This is an inaccurate statement,
and it will be corrected in a future ISTA release.

3. When removing the ignition coils and the fuel injectors from the engine, number them with the cylinder in which they came
from and reinstall them back in the same location.

4. After the cylinder head cover is removed and
before removing the exhaust camshaft place 2 wire
ties (1) on the intake VANOS gear to hold the
timing chain in place.

5. In step 13 of the ISTA repair instruction it states to remove the VANOS central bolt for the exhaust camshaft
phaser (VANOS gear). Do not remove this bolt.

6. In step 14 it states to remove the exhaust camshaft adjuster, do not remove the adjuster. Using a small paint
marker mark the VANOS gear and the adjacent chain link, this will make reassembly much easier.

7. Remove the exhaust camshaft, VANOS central bolt and VANOS adjuster as an assembly. With the timing chain
tensioner removed, it will almost provide enough slack to gently lift the chain off the exhaust VANOS gear.
Additionally, you will need to pick up the exhaust camshaft and roll it towards the intake camshaft to increase the
slack in the chain, pick up the chain and remove it from the gear. Once removedPlace it in a clean location on a shop towel
Continue with the applicable ISTA repair instruction

8. In step 20 you will reinstall the exhaust camshaft with the VANOS central bolt and exhaust VANOS gear as an
assembly.
Start with the exhaust camshaft near the intake camshaft and then roll it along the chain and into place
Align the paint mark on the VANOS gear to the marked chain link
Reinstall the camshaft bearing caps and check the cam timing with the appropriate tools
Because the exhaust VANOS central bolt was never released, it will be very clear if the exhaust camshaft is in time
or not. If needed, you will have to adjust the position of the timing chain (one tooth back or forth) on the VANOS
gear and recheck your work. Once the correct timing is verified, continue with the applicable repair instructions, and
reassemble the engine.
Copyright ©2023 BMW of North America, Inc.
about:blank

2/8

12/4/23, 6:48 PM

11 07 23_VOLUNTARY EMISSION RECALL 23E-A05: REPLACE SWITCHABLE ROCKER ARM

9. If you used the paint marker method, use solvent on a shop towel to remove the paint marks from both the
VANOS gear and the timing chain before reassembling the engine.

10. Before reinstalling the cylinder head cover, check the camshaft timing using the applicable tools and repair instructions.

The crankshaft must be pinned/locked with special tool 2 288 380.
Both camshaft adjusters (VANOS gears) must be locked with special tool 5 A53 587.
The timing chain must be pretensioned using special tool 2 455 654 to ensure the timing chain is
installed correctly. Refer to Repair Instruction 11 31 005 “Adjusting the timing of the camshafts”, see step
8. This center button the special tool will identify if the chain is correctly tensioned, over- slackened or
over-tensioned.
Check the camshaft position using the test gauge special tool 5 A7A 5B9 and basic carrier special tool 5
A4D A16.
If the cylinder head cover gasket is not damaged, it can be reused.
If the high pressure pump gasket is not damaged, it can be reused.
Repair and Tool Hints:
Cylinder 1 intermediate lever may interfere
when trying to install the intake camshaft timing
tools.
Place the VVT motor in minimum lift before
installing the camshaft timing tools.
Use a 4mm Allen socket (1) and a ratchet (2) to
turn the VVT motor clockwise until it stops at
the minimum lift end stop.

Tool 83 30 5 A53 587 may bind when removing
it from both of the VANOS adjusters, the plastic
washer (1) may be binding the tool and will not
allow it to collapse when the screw is
loosened.
Using a fine metal file, reduce the outside
diameter of the plastic washer by approximately
1 mm to avoid this interference.
Removing the washer entirely could result in
the screw and wedge falling into the engine, the
washer avoids loosening the screw too much.

Copyright ©2023 BMW of North America, Inc.
about:blank

3/8

12/4/23, 6:48 PM

11 07 23_VOLUNTARY EMISSION RECALL 23E-A05: REPLACE SWITCHABLE ROCKER ARM

Special tool 83 30 5 A4D A18 must aligned
properly with the rollers (1).
Turn the brass nut (2) to make contact with the
rollers.
Tighten the screws on the base plate of the tool
(3).
Finish compressing the springs with the brass
nut (2).
The tool must remain installed during the entire
camshaft removal and installation procedure.
If any broken or missing parts are identified in the valvetrain, please create a TSARA TC case before
continuing with this bulletin.

LABEL INSTRUCTIONS
After the vehicle has been checked and corrected, obtain a label (SD 92-435) and with the indelible marker
provided, legibly print the Recall name, recall number, and dealer code (5 digits) on the “Emissions
Recall Campaign Completed Label” (see illustration). Peel the label from its backing and affix it to the right
(passenger) rear side of the hood in the engine compartment, close to windshield.
For California centers only: It is required by the California Code of Regulations that an executed orange
"Vehicle Emission Recall - Proof of Correction" certificate (SD92-084, see illustration) be provided to each
customer (for vehicles registered in the state of California), once the Recall on his or her vehicle has been
completed.

PARTS INFORMATION
Refer to the Parts Matrix for the most up to date ordering information.
Use and invoice the applicable part numbers listed below.
G05, G06 and G07 Parts List:
Part Number
11 33 9 452 677
11 31 9 845 293
13 53 8 661 716
13 53 8 661 715
11 12 9 847 198
13 51 7 632 572
07 11 9 909 926
13 53 9 847 174
18 30 9 909 376

Description
Switchable rocker arm
Sealing sleeve
Hexagon bolt
Hexagon bolt
Profile seal
Torx socket with washer
O-ring
Sealing ring
Hexagon bolt

11 12 1 023 249

Cylinder head cover seal set

Quantity
12
1
12
8
1
2
1
6
2
1 (only if
damaged)

G70 Parts List:
Part Number
11 33 9 452 677
11 31 9 845 293
13 53 9 847 174
about:blank

Description
Switchable rocker arm
Sealing sleeve
Sealing
ring
Copyright
©2023 BMW of North America, Inc.

Quantity
12
1
6
4/8

12/4/23, 6:48 PM

11 07 23_VOLUNTARY EMISSION RECALL 23E-A05: REPLACE SWITCHABLE ROCKER ARM

13 53 8 661 716
13 53 8 661 715
11 12 9 847 198
13 51 7 632 572
07 14 9 390 155
07 14 5 A67 B87
07 11 9 906 089
07 14 7 483 888
07 14 7 283 812
07 14 8 837 399
31 11 6 899 302
07 14 9 231 837

Hexagon bolt
Hexagon bolt
Profile seal
Torx socket with washer
Hexagon screw with washer
Hexagon nut
Collar nut
Hexagon bolt
Speed nut
ASA bolt
Multi-purpose bolt
Hexagon screw with washer

11 12 1 023 249

Cylinder head cover seal set

12
8
1
2
2
1
4
4
8
4
12
4
1 (only if
damaged)

Additionally, other materials and small parts that are not specified above, such as fluids, lubricants, one-time
use screws, nuts, and seals, which must be replaced or installed according to the ISTA repair
instructions/ETK, must be selected from the Electronic Parts Catalog, or other approved BMW resources,
according to the respective vehicle type. Invoiced these items separately under the Repair Code listed in
this bulletin.
Refer to SI B10 02 15 for label ordering information.
Part Number
01 00 2 411 755
Or:
01 00 2 411 754

Description
Generic Emissions Recall Label (92-435/ Roll of 50)

Quantity
1

Emissions Recall/Proof of Correction (92-084/ Pad of 100)

1

CLAIM INFORMATION
Reimbursement for this Action will be via normal claim entry utilizing the applicable work package
information below, and when applicable, the part numbers listed above that apply.
Pluspostion (+)
Main work
Repair Code:

Completion before the first vehicle delivery to a customer or the vehicle is
already in the workshop
The vehicle arrives at your center and this Action shows open (No other Main
work will be performed or claimed during this workshop visit)
0011460700

G0x G70 Replacing switchable rocker arm exhaust

Below are the special flat rate labor operation code choices for this action.
Completion before the first vehicle delivery to a customer or the vehicle is already in the workshop
Work Pkg
#1

Labor Operation
00 74 988

Description (Plusposition work)
Replace exhaust switchable rocker arm

Labor Allowance
As applicable

00 75 594

Checking the vehicle claim history
(WVI), this issue was addressed
through a prior repair

1 FRU

Or:
#2

The vehicle arrives at your center and this Emission Recall shows open (No other Main work will be
performed or claimed during this workshop visit)
Work Pkg
#3
about:blank

Labor Operation
Description (Main work)
00 74 342 CopyrightReplace
rocker arm
©2023exhaust
BMW switchable
of North America,

Inc.

Labor Allowance
As applicable
5/8

12/4/23, 6:48 PM

11 07 23_VOLUNTARY EMISSION RECALL 23E-A05: REPLACE SWITCHABLE ROCKER ARM

Or:
#4

00 75 073

Checking the vehicle claim history (WVI),
this issue was addressed through a prior
repair

1 FRU

Only one Main work flat rate labor operation code can be claimed per workshop visit.

Claim Repair Comments
Only reference the SIB number and the work package (Pkg) number performed in the RO technician notes and the
claim comments (For example: B11 07 23 WP 1), unless otherwise required by State law.

Sublet – Bulk Materials (RO and Claim Comments Required)
Sublet Code
Up to $50.00
4

Reimbursement for the repair-related bulk materials (Do not use the
BMW part numbers for claim submission)

Sublet reimbursement calculation for claiming the applicable repair-related bulk materials (BMW part
numbers) is at the dealer net price amount for the proportional quantities used plus your center’s handling.
Enter this material cost in sublet and itemize the amount on the repair order and in claim comment section.
BMW Group’s AIR Application Resource for Flat Rate Labor Operation Codes
To obtain the corresponding flat rate unit (FRU) allowance information from the BMW Group AIR application
resource, start by entering the Chassis Number (the last seven (7) characters of the VIN, select the
applicable Model if two or more vehicle choices show), or enter the full VIN (17 characters), click on the
“Search” button. Next, click on the “Flat Rate Units” button and enter the flat rate labor operation code in the
field to the right, click “Search” to display the Flat Rate Unit Group detail choices.
Consequential Repair (RO and Claim Comments Required)
When additional or other replacement work, and/or parts (cylinder head or engine assembly) are required as a
direct result of addressing the issue outlined in this Service Information bulletin, claim these items under the special
Repair Code listed above together with the corresponding labor operation codes, including the diagnosis that
applies.
Please explain the reason for this consequential repair work (the why and the what) on the repair order and in the
claim comments section.

Alternative Mobility Solution (AMS) for Vehicle Owners (RO and Claim Comments Required)
This Action repair qualifies for Alternative Mobility Solution (AMS) expense reimbursement, claim this item
under the Defect Code noted above as follows:
Sublet Code 2 - Itemize the AMS sublet amount on the repair order and in the claim comment section.

Please refer to SI B01 29 16 for additional information.

FEEDBACK REGARDING THIS BULLETIN
Technical Feedback
Warranty Feedback

To submit feedback for the technical topic of this bulletin: Submit your
feedback in the rating box at the top of this bulletin
To submit feedback for the CLAIMS section of this bulletin: Submit an IDS
ticket to the Warranty Department, or use the chat available in the
Warranty Documentation Portal

Copyright ©2023 BMW of North America, Inc.
about:blank

6/8

12/4/23, 6:48 PM

Parts Feedback

11 07 23_VOLUNTARY EMISSION RECALL 23E-A05: REPLACE SWITCHABLE ROCKER ARM

To submit feedback for the PARTS section of this bulletin: Submit an IDS
ticket to the Parts Department

Copyright ©2023 BMW of North America, Inc.
about:blank

7/8

12/4/23, 6:48 PM

11 07 23_VOLUNTARY EMISSION RECALL 23E-A05: REPLACE SWITCHABLE ROCKER ARM

Copyright ©2023 BMW of North America, Inc.
about:blank

8/8