NHTSA ID Number: 10239656
Manufacturer Communication Number: N222375791-06
TSB/Document Date: 2023-07-25
Summary
Customer Satisfaction Program - Due to the industry-wide semiconductor shortage, the park assist feature is not functional on certain vehicles listed, built beginning December 2, 2021. The affected vehicle owners should have been made aware of the condition at sale, and notified, that once parts are available, they would be eligible for a no additional cost retrofit to enable the feature. Dealers are to replace the park assist control module to restore the Park Assist feature. Note: some vehicles may also require reprogramming of the instrument cluster or the active safety control module
Install the new Parking Assist Control Module. Refer to Parking Assist Control Module Replacement in SI.
Caution: When starting SPS2, select Reprogram NOT Replace and Reprogram.
2.
Reprogram the Parking Assist Control Module. Refer to K182 Parking Assist Control Module: Programming and
Setup in SI.
3.
Perform configuration on the Parking Assist Control Module. Refer to K182 Parking Assist Control Module:
Programming and Setup in SI.
Note: This programming event is for “Setup and Configuration” only.
4.
Perform setup and configuration on the Instrument Cluster. Refer to P16 Instrument Cluster: Programming and
Setup.
5.
Reprogram the Active Safety Control Module. Refer to K124 Active Safety Control Module: Programming and
Setup.
Page 17 of 27
Customer Satisfaction Program
N222375791 Park Assist Retrofit
5644478
Note: The screenshot above is an example of module programming and may not be indicative of the specific module that
is being programmed. Module selection and VIN information have been blacked out.
Important: To avoid warranty transaction rejections, you MUST record the warranty claim code provided on the Warranty
Claim Code (WCC) screen shown above on the job card. Refer to callout 1 above for the location of the WCC on the
screen.
6.
Record SPS Warranty Claim Code on job card for warranty transaction submission.
7.
Clear all DTCs.
Note: Depending upon vehicle RPO, it may be equipped with both front and rear parking assist or just rear park assist.
8.
Verify parking assist is now active on vehicle.
Acadia without UGN, UVZ, or UKL
6288463
Note: The wiring harness for the Parking Assist Control Module may be wrapped around an adjacent wiring harness as
shown above. Remove the attaching tape by unwrapping. Do NOT cut the tape as it could damage the wiring harness.
1.
Install the new Parking Assist Control Module. Refer to Parking Assist Control Module Replacement in SI.
Caution: When starting SPS2, select Reprogram NOT Replace and Reprogram.
2.
Reprogram the Parking Assist Control Module. Refer to K182 Parking Assist Control Module: Programming and
Setup in SI.
Page 18 of 27
Customer Satisfaction Program
N222375791 Park Assist Retrofit
3.
Perform configuration on the Parking Assist Control Module. Refer to K182 Parking Assist Control Module:
Programming and Setup in SI.
Note: This programming event is for “Setup and Configuration” only.
4.
Perform setup and configuration on the Instrument Cluster. Refer to P16 Instrument Cluster: Programming and
Setup.
5644478
Note: The screenshot above is an example of module programming and may not be indicative of the specific module that
is being programmed. Module selection and VIN information have been blacked out.
Important: To avoid warranty transaction rejections, you MUST record the warranty claim code provided on the Warranty
Claim Code (WCC) screen shown above on the job card. Refer to callout 1 above for the location of the WCC on the
screen.
5.
Record SPS Warranty Claim Code on job card for warranty transaction submission.
6.
Clear all DTCs.
Note: Depending upon vehicle RPO, it may be equipped with both front and rear parking assist or just rear park assist.
7.
Verify parking assist is now active on vehicle.
Blazer with UGN, UVZ, or UKL
6288463
Note: The wiring harness for the Parking Assist Control Module may be wrapped around an adjacent wiring harness as
shown above. Remove the attaching tape by unwrapping. Do NOT cut the tape as it could damage the wiring harness.
Page 19 of 27
Customer Satisfaction Program
N222375791 Park Assist Retrofit
1.
Install the new Parking Assist Control Module. Refer to Parking Assist Control Module Replacement in SI.
Caution: When starting SPS2, select Reprogram NOT Replace and Reprogram.
2.
Reprogram the Parking Assist Control Module. Refer to K182 Parking Assist Control Module: Programming and
Setup in SI.
3.
Perform configuration on the Parking Assist Control Module. Refer to K182 Parking Assist Control Module:
Programming and Setup in SI.
Note: This programming event is for “Setup and Configuration” only.
4.
Perform setup and configuration on the Instrument Cluster. Refer to P16 Instrument Cluster: Programming and
Setup.
5.
Reprogram the Active Safety Control Module. Refer to K124 Active Safety Control Module: Programming and
Setup.
5644478
Note: The screenshot above is an example of module programming and may not be indicative of the specific module that
is being programmed. Module selection and VIN information have been blacked out.
Important: To avoid warranty transaction rejections, you MUST record the warranty claim code provided on the Warranty
Claim Code (WCC) screen shown above on the job card. Refer to callout 1 above for the location of the WCC on the
screen.
6.
Record SPS Warranty Claim Code on job card for warranty transaction submission.
7.
Clear all DTCs.
Note: Depending upon vehicle RPO, it may be equipped with both front and rear parking assist or just rear park assist.
8.
Verify parking assist is now active on vehicle.
Page 20 of 27
Customer Satisfaction Program
N222375791 Park Assist Retrofit
Blazer without UGN, UVZ, or UKL
6288463
Note: The wiring harness for the Parking Assist Control Module may be wrapped around an adjacent wiring harness as
shown above. Remove the attaching tape by unwrapping. Do NOT cut the tape as it could damage the wiring
harness.
1.
Install the new Parking Assist Control Module. Refer to Parking Assist Control Module Replacement in SI.
Caution: When starting SPS2, select Reprogram NOT Replace and Reprogram.
2.
Reprogram the Parking Assist Control Module. Refer to K182 Parking Assist Control Module: Programming and Setup
in SI.
3.
Perform configuration on the Parking Assist Control Module. Refer to K182 Parking Assist Control Module:
Programming and Setup in SI.
Note: This programming event is for “Setup and Configuration” only.
4.
Perform setup and configuration on the Instrument Cluster. Refer to P16 Instrument Cluster: Programming and
Setup.
5644478
Note: The screenshot above is an example of module programming and may not be indicative of the specific module that
is being programmed. Module selection and VIN information have been blacked out.
Important: To avoid warranty transaction rejections, you MUST record the warranty claim code provided on the Warranty
Claim Code (WCC) screen shown above on the job card. Refer to callout 1 above for the location of the WCC on the
screen.
Page 21 of 27
Customer Satisfaction Program
N222375791 Park Assist Retrofit
5.
Record SPS Warranty Claim Code on job card for warranty transaction submission.
6.
Clear all DTCs.
Note: Depending upon vehicle RPO, it may be equipped with both front and rear parking assist or just rear park assist.
7.
Verify parking assist is now active on vehicle.
Colorado/Canyon
6288463
Note: The wiring harness for the Parking Assist Control Module may be wrapped around an adjacent wiring harness as
shown above. Remove the attaching tape by unwrapping. Do NOT cut the tape as it could damage the wiring
harness.
1.
Install the new Parking Assist Control Module. Refer to Parking Assist Control Module Replacement in SI.
Caution: When starting SPS2, select Reprogram NOT Replace and Reprogram.
2.
Reprogram the Parking Assist Control Module. Refer to K182 Parking Assist Control Module: Programming and
Setup in SI.
3.
Perform setup and configuration on the Parking Assist Control Module. Refer to K182 Parking Assist Control Module:
Programming and Setup in SI.
Note: This programming event is for “Setup and Configuration” only.
4.
Perform setup and configuration on the Instrument Cluster. Refer to P16 Instrument Cluster: Programming and Setup
in SI.
Page 22 of 27
Customer Satisfaction Program
N222375791 Park Assist Retrofit
5644478
Note: The screenshot above is an example of module programming and may not be indicative of the specific module that
is being programmed. Module selection and VIN information have been blacked out.
Important: To avoid warranty transaction rejections, you MUST record the warranty claim code provided on the Warranty
Claim Code (WCC) screen shown above on the job card. Refer to callout 1 above for the location of the WCC on the
screen.
5.
Record SPS Warranty Claim Code on job card for warranty transaction submission.
6.
Clear all DTCs.
Note: Depending upon vehicle RPO, it may be equipped with both front and rear parking assist or just rear park assist.
7.
Verify parking assist is now active on vehicle.
Traverse without UGN, UVZ, or UKL
6288463
Note: The wiring harness for the Parking Assist Control Module may be wrapped around an adjacent wiring harness as
shown above. Remove the attaching tape by unwrapping. Do NOT cut the tape as it could damage the wiring
harness.
1.
Install the new Parking Assist Control Module. Refer to Parking Assist Control Module Replacement in SI.
Caution: When starting SPS2, select Reprogram NOT Replace and Reprogram.
2.
Reprogram the Parking Assist Control Module. Refer to K182 Parking Assist Control Module: Programming and
Setup in SI.
Page 23 of 27
Customer Satisfaction Program
N222375791 Park Assist Retrofit
3.
Perform setup and configuration on the Parking Assist Control Module. Refer to K182 Parking Assist Control Module:
Programming and Setup in SI.
Note: This programming event is for “Setup and Configuration” only.
4.
Perform setup and configuration on the Instrument Cluster. Refer to P16 Instrument Cluster: Programming and Setup
in SI.
5644478
Note: The screenshot above is an example of module programming and may not be indicative of the specific module that
is being programmed. Module selection and VIN information have been blacked out.
Important: To avoid warranty transaction rejections, you MUST record the warranty claim code provided on the Warranty
Claim Code (WCC) screen shown above on the job card. Refer to callout 1 above for the location of the WCC on the
screen.
5.
Record SPS Warranty Claim Code on job card for warranty transaction submission.
6.
Clear all DTCs.
Note: Depending upon vehicle RPO, it may be equipped with both front and rear parking assist or just rear park assist.
7.
Verify parking assist is now active on vehicle.
Traverse with UGN, UVZ, or UKL
6288463
Page 24 of 27
Customer Satisfaction Program
N222375791 Park Assist Retrofit
Note: The wiring harness for the Parking Assist Control Module may be wrapped around an adjacent wiring harness as
shown above. Remove the attaching tape by unwrapping. Do NOT cut the tape as it could damage the wiring harness.
1.
Install the new Parking Assist Control Module. Refer to Parking Assist Control Module Replacement in SI.
Caution: When starting SPS2, select Reprogram NOT Replace and Reprogram.
2.
Reprogram the Parking Assist Control Module. Refer to K182 Parking Assist Control Module: Programming and
Setup in SI.
3.
Perform configuration on the Parking Assist Control Module. Refer to K182 Parking Assist Control Module:
Programming and Setup in SI.
Note: This programming event is for “Setup and Configuration” only.
4.
Perform setup and configuration on the Instrument Cluster. Refer to P16 Instrument Cluster: Programming and
Setup.
5.
Reprogram the Active Safety Control Module. Refer to K124 Active Safety Control Module: Programming and
Setup.
5644478
Note: The screenshot above is an example of module programming and may not be indicative of the specific module that
is being programmed. Module selection and VIN information have been blacked out.
Important: To avoid warranty transaction rejections, you MUST record the warranty claim code provided on the Warranty
Claim Code (WCC) screen shown above on the job card. Refer to callout 1 above for the location of the WCC on the
screen.
6.
Record SPS Warranty Claim Code on job card for warranty transaction submission.
7.
Clear all DTCs.
Note: Depending upon vehicle RPO, it may be equipped with both front and rear parking assist or just rear park assist.
8.
Verify parking assist is now active on vehicle.
Dealer Responsibility
All new, used, GM Certified Used, courtesy transportation vehicles, dealer shuttle vehicles, etc. in dealers' possession
and subject to this program must be held and inspected/repaired per the service procedure of this bulletin before
customers take possession of these vehicles. Involved vehicles must be held and not delivered to customers, dealertraded, released to auction, used for demonstration, or any other purpose.
All GM Certified Used vehicles currently in the dealers’ inventory within the Certified Pre-Owned Inventory System
(CPOIS) will be de-certified and must be held and remedied per the service procedure in this bulletin. Upon submitting
an accepted/paid warranty transaction in the Global Warranty Management (GWM) system, the vehicle can be re-certified
for sale within the CPOIS system, or once again be used in the CTP program.
Dealers are to service all vehicles subject to this program at no charge to customers, regardless of mileage, age of vehicle,
or ownership, through August 31, 2026. Customers who have recently purchased vehicles sold from your vehicle
inventory, and for which there is no customer information indicated on the involved vehicle listing, are to be contacted by
Page 25 of 27
Customer Satisfaction Program
N222375791 Park Assist Retrofit
the dealer. Arrangements are to be made to make the required correction according to the instructions contained in this
bulletin. A copy of the customer letter is provided in this bulletin for your use in contacting customers. Program followup cards should not be used for this purpose, since the customer may not as yet have received the notification letter.
In summary, whenever a vehicle subject to this program enters your vehicle inventory or is in your facility for service
through August 31, 2026, you must take the steps necessary to be sure the program correction has been made before
selling or releasing the vehicle.
Dealer Reports – For USA & Export
For dealers with involved vehicles, a listing has been prepared and will be available through GM GlobalConnect Maxis
Field Action Reports or sent directly to export dealers. The Inventory tab of the dealer reports will contain VINs that
apply to this field action. This information is intended to assist dealers with the PROMPT COMPLETION of these
vehicles. The Customer In-Service tab will contain customer names and addresses from Motor Vehicle Registration
Records. The use of such motor vehicle registration data for any purpose other than follow-up necessary to complete
this field action may be a violation of law in several states.
Courtesy Transportation – For USA & Canada
Courtesy transportation is available for customers whose vehicles are involved in a product program and still within the
warranty coverage period. See General Motors Service Policies and Procedures Manual for courtesy transportation
program details.
Customer Notification
USA & Canada - General Motors will notify customers of this program on their vehicle (see copy of customer letter included
with this bulletin).
Export - Letters will be sent to known owners of record located within areas covered by the US National Traffic and Motor
Vehicle Safety Act. For owners outside these areas, dealers should notify customers using the attached sample letter.
GM bulletins are intended for use by professional technicians, NOT a "do-it-yourselfer". They are written to inform these technicians of
conditions that may occur on some vehicles, or to provide information that could assist in the proper service of a vehicle. Properly trained
technicians have the tools, equipment, safety instructions, and know-how to do a job properly and safely. If a condition is described, DO NOT
assume that the bulletin applies to your vehicle, or that your vehicle will have that condition. See your dealer for information on whether your
vehicle may benefit from the information.
We Support
Voluntary Technician
Certification
Page 26 of 27
Customer Satisfaction Program
N222375791 Park Assist Retrofit
This notice applies to your vehicle, VIN: ________________________________
Dear General Motors Customer:
Our records indicate that, at the time you purchased or leased your GM vehicle, the vehicle was not equipped with Rear
or Front and Rear Park Assist due to an industry-wide parts shortage.
We are pleased to inform you that you are now able to schedule an appointment with your GM dealer so they can
enable your Rear or Front and Rear Park Assist feature.
What We Will Do: Your GM dealer will install the required parts and software in your vehicle to enable your Rear or
Front and Rear Park Assist feature. This service will be performed for you at no charge until August 31, 2026.
What You Should Do: We recommend that you contact your GM dealer as soon as possible to schedule an
appointment for this retrofit. By scheduling an appointment, your dealer can order the necessary parts to be available
on your scheduled appointment date.
If you have any questions or concerns that your dealer is unable to resolve, please contact the appropriate Customer
Assistance Center at the number listed below.
For the hearing or speech impaired, please contact our Customer Assistance Center using the Telecommunication
Relay Service by dialing 711 then providing the appropriate Customer Assistance Center number for your vehicle.
Division
Cadillac
Chevrolet
GMC
Puerto Rico – English
Puerto Rico – Español
Virgin Islands
Number
1-800-333-4223
1-800-222-1020
1-800-462-8782
1-866-467-9700
1-866-467-9700
1-866-467-9700
Text Telephones (TTY)
711 / 1-800-833-2438
711 / 1-800-833-2438
711 / 1-800-833-2438
We truly appreciate you taking the time to retrofit your vehicle as we know your time is valuable. We want you to know
that we will do our best, throughout your ownership experience, to ensure that your GM vehicle provides you with many
miles of enjoyable driving.
Neelie O’Connor
Global Executive Director
Customer Experience Operations
N222375791
Page 27 of 27
If the PDF is very large, it may not load in the preview below.
Some older TSBs had multiple PDFs — visit the NHTSA Website to view all PDFs.
If the TSB PDF does not show, download or view it on the NHTSA Website.
Click on the (+) Plus Sign
Then Click on Associated Document(s)
Search NHTSA Database for Recalls
Search NHTSA Database for Vehicle Investigations
View Latest Vehicle Investigations
Search NHTSA Database for Vehicle Complaints
View Latest Vehicle Complaints
TSB/Document ID: N222375791-06
Replacement Service Bulletin Number:
MFR Communication Date: 2023-07-25
MFR Internal Campaign ID/Software Version:
Communication Type: Service Bulletin/Repair Instructions
NHTSA Components: ELECTRICAL SYSTEM:ADAS:PARKING ASSIST:WARNING
MFR Component System:
MFR Component Subsystem:
Previous TSB | Next TSB |
- [Notice] When you receive a used device, it may be a customer return resold by Amazon without inspection. You can exchange it for a new one through Amazon. As this situation is unavoidable, we sincerely apologize. For any issues, contacting us via Amazon's "Messages" is the best way. THINKSCAN 689BT Bidirectional Scan Tool Can Be Used Immediately After It is Turned On, Without Complicated Registration Process, Which is More Convenient & Quick.
- Full Bi-Directional Control & 3000+ Active Tests: Take control and test components like actuators, fuel injectors, relays, and cooling fans in real time. You’ll quickly see if the problem is in the part itself or the control module — saving you hours of guesswork and frustrating trial-and-error.
- Advanced ECU Coding Capabilities: Handle module matching and hidden feature activation with confidence. When you replace an ECU or want to customize settings, this obd2 scanner diagnostic bi directional tool gives you the professional-level capabilities you need without the dealership price tag.
- 34+ Useful Reset and Maintenance Functions: Complete everyday service tasks smoothly with a wide range of helpful reset and maintenance functions. Whether you’re keeping up with regular upkeep or tackling a specific job, this scanner makes maintenance simpler and less stressful for both DIYers and pros.
- Comprehensive Full System Diagnostics: Diagnose every major system — Engine, Transmission, ABS, SRS, TPMS, and more — all in one place. Finally stop wondering if you’re missing something important; get the full picture and clear codes with ease.
- Top Reasons to Choose the D7S OBD2 Scanner: XTOOL D7S car scan tool, an upgrade of XTOOL D7, offers comprehensive features for automotive technicians, workshops, and DIY enthusiasts 1. Upgraded Hardware: 2+64GB memory, rear camera, intuitive interface, foldable bracket 2. Complete Diagnostics: FCA
Autoauth, OE-level all system scan, 39+ maintenance services, 4K+ bidirectional, CANFD/DoIP protocol 3. Advanced Capabilities: ECU coding, PMI functions 4. Wide Compatibility: Support 10,000+ models, covering 99% vehicle brands 5. Multi-language: Available in 22+ languages, No IP Restrictions 6. 3-Year Updates: Save 300 bucks on software updates for the latest features and optimizations - 2026 Upgraded D7S Car Scanner Features: The newly 2026 D7S V2.0 scanner for car brings exciting features for advanced vehicle diagnostics and enhanced user experience 1. FCA AutoAuth: Now supports FCA SGW module for Chrysler, for Jeep, for Dodge (2018+), for Fiat (2017+), enabling faster vehicle communication without gateway restrictions 2. PMI (Offline ECU Programming): Allows for Ford, for Lincoln, and for Mazda ECU programming for new modules 3. Optimized Diagnostic Report 2.0: Personalized reports with logos and customer info for auto shops. Note: Compatibility varies by cars, please check before order
- Cost-effective ECU Coding Scan Tool for Specific Brands: Enhance your vehicle's performance with XTOOL D7S! This obd2 scanner all systems bidirectional offers advanced capabilities at an affordable price, supports online for BMW, for Benz and offline for BENZ, for MIT, along with PMI functions for Ford, for Mazda, and for Lincoln. Ideal for technicians and DIY enthusiasts, this automotive scanner diagnostic tool optimizes vehicle performance and enhances the driving experience. Note: Not for all cars and modules, please send car VIN to check the compatibility before purchase
- OE All System Diagnostic & 8 Pids Graphing: XTOOL D7S is a comprehensive all system bi directional obd2 scanner that delivers dealer-level diagnostics, completely controlling over your vehicle’s performance and health. This automotive scan tool can read and clear DTCs, view live data and ECU information, retrieve freeze frames, and perform active tests and full obd2 functions. This bi-directional scan tool can can identify your vehicle's make, model, and year information with just one click and show up to 8 PIDs live data with options for CSV viewing, playback, and recording for in-depth analysis. It is easy-to-use for both professionals and beginners, helping pinpoint issues efficiently
- 3 Years Software Update, Value for Money: With 3 years of software updates and 22+ languages(no IP restrictions), XTOOL D7S auto scanner code scanner ensures ongoing compatibility for the latest car models and improved diagnostic functions. This all system vehicle diagnostic scanner comes with a 30-day return policy and a 24-month repair for dependable performance. XTOOL are dedicated to your satisfaction, so enjoy seamless support and lifetime expert assistance. Should you encounter any issues or concerns, don’t hesitate to reach out XTOOL. D7S with newest update with 22 languages freely transfer without authorization, check details from setting-language or from XTOOL
Autoauth, OE-
- 🔥 Historical lowest pr-ice now on sa-le--hot se-lling.
- 【🎈𝗜𝗙𝟳𝟰𝟱 𝗽𝗲𝗿𝗳𝗼𝗿𝗺𝘀 𝟲 𝗲𝘀𝘀𝗲𝗻𝘁𝗶𝗮𝗹 𝗿𝗲𝘀𝗲𝘁 𝗳𝘂𝗻𝗰𝘁𝗶𝗼𝗻𝘀—𝗔𝗕𝗦 𝗕𝗹𝗲𝗲𝗱𝗶𝗻𝗴, 𝗢𝗶𝗹 𝗥𝗲𝘀𝗲𝘁, 𝗘𝗣𝗕, 𝗦𝗔𝗦, 𝗧𝗵𝗿𝗼𝘁𝘁𝗹𝗲 𝗥𝗲𝗹𝗲𝗮𝗿𝗻, 𝗮𝗻𝗱 𝗕𝗠𝗦—𝗽𝘂𝘁𝘁𝗶𝗻𝗴 𝗽𝗿𝗼𝗳𝗲𝘀𝘀𝗶𝗼𝗻𝗮𝗹-𝗴𝗿𝗮𝗱𝗲 𝗺𝗮𝗶𝗻𝘁𝗲𝗻𝗮𝗻𝗰𝗲 𝗯𝗮𝗰𝗸 𝗶𝗻 𝘆𝗼𝘂𝗿 𝗵𝗮𝗻𝗱𝘀.】Spongy brakes? Stuck oil light? Parking brake won't release? Off-center steering? Rough idle after battery disconnect? Draining battery? IF745 handles all with a few taps. One tool covers six dealer-level resets, saving hundreds in labor costs. ❗ NOTE: Does NOT support bidirectional control, coding, or programming.
- 【✨ 𝗜𝗙𝟳𝟰𝟱 𝗴𝗼𝗲𝘀 𝗯𝗲𝘆𝗼𝗻𝗱 𝗯𝗮𝘀𝗶𝗰 𝗰𝗼𝗱𝗲 𝗿𝗲𝗮𝗱𝗶𝗻𝗴 𝘄𝗶𝘁𝗵 𝟭𝟬 𝗶𝗻𝘁𝗲𝗴𝗿𝗮𝘁𝗲𝗱 𝗳𝘂𝗻𝗰𝘁𝗶𝗼𝗻𝘀—𝗗𝗧𝗖 𝗟𝗼𝗼𝗸𝘂𝗽, 𝗜/𝗠 𝗥𝗲𝗮𝗱𝗶𝗻𝗲𝘀𝘀, 𝗙𝗿𝗲𝗲𝘇𝗲 𝗙𝗿𝗮𝗺𝗲, 𝗟𝗶𝘃𝗲 𝗗𝗮𝘁𝗮, 𝗢𝟮𝗦, 𝗢𝗕𝗠, 𝗘𝗩𝗔𝗣, 𝗮𝗻𝗱 𝗺𝗼𝗿𝗲. 】Pulling a code tells you something is wrong. IF745 tells you what the code means, when the fault happened, and what data surrounds it. Pass emissions with one I/M Readiness tap. Freeze the fault moment with Freeze Frame. Monitor live sensor data in real time. Turn cryptic codes into clear answers.
- 【🛒 𝗜𝗙𝟳𝟰𝟱 𝗽𝗲𝗿𝗳𝗼𝗿𝗺𝘀 𝗳𝘂𝗹𝗹-𝘀𝘆𝘀𝘁𝗲𝗺 𝗱𝗶𝗮𝗴𝗻𝗼𝘀𝘁𝗶𝗰𝘀 𝗮𝗰𝗿𝗼𝘀𝘀 𝗮𝗹𝗹 𝗺𝗼𝗱𝘂𝗹𝗲𝘀—𝗲𝗻𝗴𝗶𝗻𝗲, 𝗔𝗕𝗦, 𝗮𝗶𝗿𝗯𝗮𝗴, 𝘁𝗿𝗮𝗻𝘀𝗺𝗶𝘀𝘀𝗶𝗼𝗻, 𝘀𝘁𝗲𝗲𝗿𝗶𝗻𝗴, 𝘀𝘂𝘀𝗽𝗲𝗻𝘀𝗶𝗼𝗻, 𝗯𝗼𝗱𝘆 𝗲𝗹𝗲𝗰𝘁𝗿𝗼𝗻𝗶𝗰𝘀, 𝗮𝗻𝗱 𝗺𝗼𝗿𝗲. 】Warning lights on but you don't know why? Skip the $100+ diagnostic fee at the shop. Run a complete self-check from your driveway. IF745 reads and clears fault codes, retrieves ECU info, and displays live data from every accessible module—delivering a full vehicle health report in minutes, without leaving home.
- 【✅𝗜𝗙𝟳𝟰𝟱 𝗳𝗲𝗮𝘁𝘂𝗿𝗲𝘀 𝗮 𝟳-𝗶𝗻𝗰𝗵 𝗱𝗶𝘀𝗽𝗹𝗮𝘆, 𝗲𝗿𝗴𝗼𝗻𝗼𝗺𝗶𝗰 𝗱𝗲𝘀𝗶𝗴𝗻, 𝗪𝗶-𝗙𝗶 𝘂𝗽𝗱𝗮𝘁𝗲𝘀, 𝗮𝗻𝗱 𝘇𝗲𝗿𝗼 𝘀𝘂𝗯𝘀𝗰𝗿𝗶𝗽𝘁𝗶𝗼𝗻 𝗳𝗲𝗲𝘀 𝗳𝗼𝗿 𝗵𝗮𝘀𝘀𝗹𝗲-𝗳𝗿𝗲𝗲 𝗱𝗶𝗮𝗴𝗻𝗼𝘀𝘁𝗶𝗰𝘀.】Large screen means no squinting. Intuitive navigation and customizable data displays put key info at your fingertips. Wi-Fi delivers lifetime free updates without a computer. No recurring fees. No hidden costs. Just a reliable tool that works as hard as you do.
This product presentation was made with AAWP plugin.