GLOBAL SAFETY FIELD INVESTIGATIONS
DCS6617
URGENT - DISTRIBUTE IMMEDIATELY
Date:

June 30, 2023

Subject: REVISION: N222392960-03 – Customer Satisfaction Program
Super Cruise and Surround Vision System Activation
Revised Service Procedure
Models: 2023 Cadillac LYRIQ
To:

All General Motors Dealers

This bulletin has been revised to return to the service procedure published in
N222392960-01. Please discard all previous copies of bulletin N222392960.
END OF MESSAGE
GLOBAL SAFETY FIELD INVESTIGATIONS

Customer Satisfaction Program
N222392960 Super Cruise and Surround Vision System Activation
Release Date:

June 2023

Revision:

03

Revision Description: This bulletin has been revised to return to the service procedure published in N22239296001. Please discard all previous copies of bulletin N222392960.
Attention:

This field action must only be completed by Cadillac dealers who have met EV Readiness
Requirements, and the repair must be performed by a technician who has successfully completed the
required training.
For Canadian Dealers: Only Cadillac Dealers who have signed the Cadillac Retail and Facility
Standards Addendum and have met all the Cadillac LYRIQ-specific training, tools, and equipment
requirements are eligible to complete the repair. Any Dealer unsure of their eligibility status should
immediately review with their District Service Manager.
This program is in effect until July 31, 2025.

Make
Cadillac

Model
LYRIQ

Model Year
From
To
2023
2023

RPO

Description

Involved vehicles are marked “Open” on the Investigate Vehicle History screen in GM Global Warranty Management
system. This site should always be checked to confirm vehicle involvement prior to beginning any required inspections
and/or repairs.
Condition
Correction

Certain 2023 model year Cadillac LYRIQ vehicles may have a condition where the Super Cruise and
Surround Vision features are not activated.
Dealers are to reprogram the image processing module and if necessary, reprogram the short range
radar sensors.

Parts
No parts are required for this repair.
Warranty Information
Labor
Operation
9106631*
9106539*
9106637*
Important:

Description
Image Processing Control Module reprogramming and verify Short
Range Radar Reprogramming with SPS
Image Processing Control Module and Short Range Radar
Reprogramming with SPS
USE ONLY IF VCI reprogramming with SPS is required

Labor
Time

Trans.
Type

Net
Item

ZFAT

N/A

3.4
3.6
4.2

* To avoid warranty transaction rejections, carefully read and follow the instructions below:

6125814

• The Warranty Claim Code from the programming event must be accurately entered in the “Warranty Claim
Code” field of the transaction.
•

When more than one Warranty Claim Code is generated for a programming event, it is required to document all
Warranty Claim Codes in the “Correction” field on the job card. Dealers must also enter one of the codes in the

Copyright 2023 General Motors. All Rights Reserved.

Page 1 of 12

Customer Satisfaction Program
N222392960 Super Cruise and Surround Vision System Activation
“Warranty Claim Code” field of the transaction, otherwise the transaction will reject. It is best practice to enter
the FINAL code provided by SPS2.

Warranty Claim Code Information Retrieval

6125774

If the Warranty Claim Code was not recorded on the Job Card, the code can be retrieved in the SPS2 system as
follows:
1.
2.
3.
4.

Open TLC on the computer used to program the vehicle.
Select and start SPS2.
Select Settings (1).
Select the Warranty Claim Code tab (2).

The VIN, Warranty Claim Code and Date/Time will be listed on a roster of recent programming events. If the code is
retrievable, dealers should resubmit the transaction making sure to include the code in the SPS Warranty Claim Code
field.
Service Procedure
Caution: Before downloading the update files, be sure the computer is connected to the internet through a network cable
(hardwired). DO NOT DOWNLOAD or install the files wirelessly. If there is an interruption during programming,
programming failure or control module damage may occur.
Note: Carefully read and follow the instructions below.

•

Ensure the programming tool is equipped with the latest software and is securely connected to the data link connector.
If there is an interruption during programming, programming failure or control module damage may occur.

•

Stable battery voltage is critical during programming. Any fluctuation, spiking, over voltage or loss of voltage will
interrupt programming. Install a GM Authorized Programming Support Tool to maintain system voltage. Refer to
www.gmdesolutions.com for further information. If not available, connect a fully charged 12 V jumper or booster
pack disconnected from the AC voltage supply. DO NOT connect a battery charger.

•

Follow the on-screen prompts regarding ignition power mode, but ensure that anything that drains excessive power
(exterior lights, HVAC blower motor, etc) is off.

•

Clear DTCs after programming is complete. Clearing powertrain DTCs will set the Inspection/Maintenance (I/M)
system status indicators to NO.

Important: The service technician always needs to verify that the VIN displayed in the TLC left side drop down menu and
the top center window match the VIN plate of the vehicle to be programmed prior to using Service Programming System
2 (SPS2) for programming or reprogramming a module.
Page 2 of 12

Customer Satisfaction Program
N222392960 Super Cruise and Surround Vision System Activation
•

For the TLC application, service technicians need to always ensure that the power mode (ignition) is “ON” before
reading the VIN from the vehicle’s VIN master module and that they do not select a VIN that is already in the TLC
application memory from a previous vehicle.

•

If the VIN that shows up in the TLC top center window after correctly reading the VIN from the vehicle does not match
the VIN plate of the vehicle, manually type in the VIN characters from the vehicle VIN plate into the TLC top center
window and use these for programming or reprogramming the subject module with the correct vehicle VIN and
software and/or calibrations.

•

The Engine Control Module (ECM) is the master module (for VIP vehicles) that TLC reads to determine the VIN of
the vehicle. If the VIN read from the vehicle by TLC does not match the VIN plate of the vehicle, the ECM also needs
to be reprogrammed with the correct VIN, software and calibrations that match the vehicle’s VIN plate.

•

The Body Control Module (BCM) is the master module (for GEM vehicles) that TLC reads to determine the VIN of
the vehicle. If the VIN read from the vehicle by TLC does not match the VIN plate of the vehicle, the BCM also needs
to be reprogrammed with the correct VIN, software and calibrations that match the vehicle’s VIN plate.

Caution: Be sure the VIN selected in the drop down menu (1) is the same as the vehicle connected (2) before beginning
programming.

5743643

Important: If the vehicle VIN DOES NOT match, the message below will be shown.

5877000

Page 3 of 12

Customer Satisfaction Program
N222392960 Super Cruise and Surround Vision System Activation

5644477

Important: Techline Connect screens shown above.
Important: If the same calibration/software warning is noted on the TLC Summary screen, select OK and follow
screen instructions. After a successful programming event, the WCC is located in the Service Programming System
dialogue box of the SPS Summary screen. No further action is required. Refer to the Warranty section of the bulletin.

5931076

Note: Left side shown, right side similar.
1.

Using a flat-bladed plastic trim tool, release the retaining clips.

2.

Pull rearward to clear the tab and remove the Right Instrument Panel Outer Trim Cover (1).

Page 4 of 12

Customer Satisfaction Program
N222392960 Super Cruise and Surround Vision System Activation

5951923

3.

Using a flat-bladed plastic trim tool, release the retaining clips.

4.

Pull the Instrument Panel Fuse Block Access Hole Cover (1) rearward and then to the right to clear the “T” shape
tabs.

5.

Remove the Instrument Panel Fuse Block Access Hole Cover (1).

6305450

6.

Locate and remove F22 (1) and F25 (2) fuses.

7.

Wait a minimum of 30 seconds, then reinstall F22 (1) and F25 (2).

Page 5 of 12

Customer Satisfaction Program
N222392960 Super Cruise and Surround Vision System Activation

5951923

8.

Insert the tabs into the “T” shape slots and secure the clips installing the Instrument Panel Fuse Block Access Hole
Cover (1) to the instrument panel compartment.

5931076

Note: Left side shown, right side similar.
9.

Insert the tab at the top of the Instrument Panel Outer Trim Cover (1) into the instrument panel before installing.

10. Install the Instrument Panel Outer Trim Cover – Right Side (1).
11. This process will take more than 2.5 hours to complete. Please perform the following steps before attempting to
program:
•
•
•
•
•
•
•

Make sure, if using a laptop, to be connected to the power supply.
Connect PC or laptop to the internet with a network cable. Do not download and install wirelessly.
Be sure all connections are secure.
Connect MDI2 via USB to laptop.
Do not open and close the doors once programming starts.
DO NOT let the computer go to sleep.
Stable battery voltage is critical during programming. Any fluctuation, spiking, over voltage or loss of
voltage will interrupt programming. Install a GM Authorized Programming Support Tool to maintain system
voltage. Refer to www.gmdesolutions.com for further information. If not available, connect a fully charged
12 V jumper or booster pack disconnected from the AC voltage supply. DO NOT connect a battery charger.

Page 6 of 12

Customer Satisfaction Program
N222392960 Super Cruise and Surround Vision System Activation
12. Prior to performing this field action, be sure MDI2 has been updated to software version 9.1.1766.85 or most recent
update.
13. If computer is running Windows 11, disable all spyware anti-viruses and firewalls.
14. Connect the MDI2 and open Techline Connect.
Caution: If Techline Connect is already open prior to working on the vehicle, close and reopen Techline Connect.
Due to the length of the reprogramming Techline Connect could time out if a new session is not started.
15. Open GDS2.
16. Select “Vehicle Diagnostics”.
17. Select “Vehicle DTC Information”.
18. Clear all DTCs.
19. Close GDS2.
Note: SI refers to sensors separately but in SPS2 there is one programming option. Select B233 Short Range Radar
Sensor in SPS2.
20. Reprogram the Short Range Radar Sensors. Refer to Short Range Radar Sensor Programming and Setup in SI.
21. After programming is complete and the warranty claim code is recorded, select “Proceed Same VIN”.
Caution: Once the estimated time remaining stabilizes (may take up to 20 minutes), programming should take less than
3 hours. If the timer shows more than 3 hours, cancel the programming event and retry. Otherwise, part damage may
occur.
Note: Service information does not currently have supporting information for K124 Image Processing Module
reprogramming. Follow all on screen instructions in SPS.
22. On the SPS Supported Controllers screen, select K124 Image Processing Module – Programming and follow the onscreen instructions.
•
•

If programming completes, proceed to step 23.
If programming is unsuccessful, refer to the Unsuccessful Programming section below.

6282312

Note: During programming, this screen will show around the 45 minute to 1 hour mark after programming begins. This is
normal.

Page 7 of 12

Customer Satisfaction Program
N222392960 Super Cruise and Surround Vision System Activation

5644478

Note: The screenshot above is an example of module programming and may not be indicative of the specific module
that is being programmed. Module selection and VIN information have been blacked out.
Important: To avoid warranty transaction rejections, you MUST record the warranty claim code provided on the
Warranty Claim Code (WCC) screen shown above on the job card. Refer to callout 1 above for the location of the
WCC on the screen.
23. After all programming is complete, clear DTC’s.
Note: If vehicles are located outside of the US or Canada, a test drive to validate the functionality of super cruise will
not be possible. However, it is still necessary to confirm the 360 camera functions properly.
24. A test drive is required. Navigate to a supported super cruise road. Refer to https://www.cadillac.com/world-ofcadillac/innovation/super-cruise.
25. Test drive and confirm super cruise and 360 camera operation.
26. Record SPS Warranty Claim Code on job card for warranty transaction submission.
Unsuccessful Programming
1.

Open GDS2 home.

2.

Select the vehicle.

3.

Select “Module Diagnostics”.

4.

Select “[K124AA] Image Processing Module 1 – Processor 1”.

5.

Select “Identification Information”.

6306235

6.

Record the value shown for “Calibration Part Number 8” shown above.
Page 8 of 12

Customer Satisfaction Program
N222392960 Super Cruise and Surround Vision System Activation

6306239

7.

Select “Back” twice to return to the main module screen shown above.

8.

Select “[K124AB] Image Processing Module 1 – Processor 2”.

9.

Select “Identification Information”.

6306236

10. Record the value shown for “Calibration Part Number 1” shown above.
11. Close out of GDS2
12. Contact Techline Customer Support (TCSC) @ 1-800-828-6860 (English) or 1-800-503-3222 (French) to setup a
case. The required information will be the VIN, field action number N222392960, and the recorded Calibration Part
Numbers. TCSC will provide a programming VCI number, if required.

Page 9 of 12

Customer Satisfaction Program
N222392960 Super Cruise and Surround Vision System Activation

5644478

Note: The screenshot above is an example of module programming and may not be indicative of the specific module
that is being programmed. Module selection and VIN information have been blacked out.
Important: To avoid warranty transaction rejections, you MUST record the warranty claim code provided on the
Warranty Claim Code (WCC) screen shown above on the job card. Refer to callout 1 above for the location of the
WCC on the screen.
13. After all programming is complete, clear DTC’s.
Note: If vehicles are located outside of the US or Canada, a test drive to validate the functionality of super cruise will
not be possible. However, it is still necessary to confirm the 360 camera functions properly.
14. A test drive is required. Navigate to a supported super cruise road. Refer to https://www.cadillac.com/world-ofcadillac/innovation/super-cruise.
15. Test drive and confirm super cruise and 360 camera operation.
16. Record SPS Warranty Claim Code on job card for warranty transaction submission.
Dealer Responsibility
All new, used, GM Certified Used, courtesy transportation vehicles, dealer shuttle vehicles, etc. in dealers' possession
and subject to this program must be held and inspected/repaired per the service procedure of this bulletin before
customers take possession of these vehicles. Involved vehicles must be held and not delivered to customers, dealertraded, released to auction, used for demonstration, or any other purpose.
All GM Certified Used vehicles currently in the dealers’ inventory within the Certified Pre-Owned Inventory System
(CPOIS) will be de-certified and must be held and remedied per the service procedure in this bulletin. Upon submitting
an accepted/paid warranty transaction in the Global Warranty Management (GWM) system, the vehicle can be re-certified
for sale within the CPOIS system, or once again be used in the CTP program.
Dealers are to service all vehicles subject to this program at no charge to customers, regardless of mileage, age of vehicle,
or ownership, through July 31, 2025. Customers who have recently purchased vehicles sold from your vehicle inventory,
and for which there is no customer information indicated on the involved vehicle listing, are to be contacted by the dealer.
Arrangements are to be made to make the required correction according to the instructions contained in this bulletin. A
copy of the customer letter is provided in this bulletin for your use in contacting customers. Program follow-up cards
should not be used for this purpose, since the customer may not as yet have received the notification letter.
In summary, whenever a vehicle subject to this program enters your vehicle inventory or is in your facility for service
through July 31, 2025, you must take the steps necessary to be sure the program correction has been made before selling
or releasing the vehicle.
Dealer Reports – For USA & Export
For dealers with involved vehicles, a listing has been prepared and will be available through GM GlobalConnect Maxis
Field Action Reports or sent directly to export dealers. The Inventory tab of the dealer reports will contain VINs that
apply to this field action. This information is intended to assist dealers with the PROMPT COMPLETION of these
vehicles. The Customer In-Service tab will contain customer names and addresses from Motor Vehicle Registration
Records. The use of such motor vehicle registration data for any purpose other than follow-up necessary to complete
this field action may be a violation of law in several states.

Page 10 of 12

Customer Satisfaction Program
N222392960 Super Cruise and Surround Vision System Activation
Courtesy Transportation – For USA & Canada
Courtesy transportation is available for customers whose vehicles are involved in a product program and still within the
warranty coverage period. See General Motors Service Policies and Procedures Manual for courtesy transportation
program details.
Customer Notification
USA & Canada - General Motors will notify customers of this program on their vehicle (see copy of customer letter included
with this bulletin).

GM bulletins are intended for use by professional technicians, NOT a "do-it-yourselfer". They are written to inform these technicians of
conditions that may occur on some vehicles, or to provide information that could assist in the proper service of a vehicle. Properly trained
technicians have the tools, equipment, safety instructions, and know-how to do a job properly and safely. If a condition is described, DO NOT
assume that the bulletin applies to your vehicle, or that your vehicle will have that condition. See your dealer for information on whether your
vehicle may benefit from the information.

We Support
Voluntary Technician
Certification

Page 11 of 12

Customer Satisfaction Program
N222392960 Super Cruise and Surround Vision System Activation
April 2023
This notice applies to your vehicle, VIN: ________________________________
Dear General Motors Customer:
Thank you for being among our first Cadillac LYRIQ owners. Your LYRIQ is already equipped with many innovative
features and technologies, and now it’s getting even better. As you know, your LYRIQ is equipped with Super Cruise™
driver assistance technology and HD Surround Vision hardware. Your Super Cruise and HD Surround Vision software
updates for your LYRIQ are now available.
This service will be performed for you at no charge until July 31, 2025. After that, any applicable warranty will apply.
What You Should Do: To enable these features in your LYRIQ as soon as possible, it will require a service
appointment at your dealership. To schedule your complimentary appointment at a time that is convenient for you, we
recommend that you contact either the Cadillac EV Concierge at 1-844-EVCADILLAC or your preferred Cadillac
dealership directly. When scheduling your appointment, confirm with the dealer that they are an EV certified dealer.
If you have any questions or concerns that your dealer is unable to resolve, please contact the appropriate Customer
Assistance Center at the number listed below.
For the hearing or speech impaired, please contact our Customer Assistance Center using the Telecommunication
Relay Service by dialing 711 then providing the appropriate Customer Assistance Center number for your vehicle.
Division
Cadillac LYRIQ EV
Puerto Rico – English
Puerto Rico – Español
Virgin Islands

Number
1-844-EV-CADILLAC
(1-844-382-2345)
1-866-467-9700
1-866-467-9700
1-866-467-9700

Text Telephones (TTY)
711 / 1-800-833-2438

We appreciate your commitment to an iconic LYRIQ lifestyle, and hope you’ll enjoy many miles of hands-free driving
experiences on compatible roads.
Neelie O’Connor
Global Executive Director
Customer Experience Operations
N222392960

Page 12 of 12