NHTSA ID Number: 10237234
Manufacturer Communication Number: TKA-20R,TKB-20R,
TSB/Document Date: 2023-06-05
Summary
Takata Front Passenger Airbag Module / Inflator “Like for Like†Recall
Document the presence of the aftermarket or counterfeit device on the repair order and with
photos. Report this information immediately on a Quality Monitoring Report (QMR).
IMPORTANT: When entering a related QMR, use failure code ULF and NOT the campaign fail
code.
•
Once the QMR has been submitted, contact the Subaru
Claims Helpline to discuss the details.
They will advise you on how to proceed with treatment of the open campaign.
Continued...
Bulletin Number: TKA-20R / TKB-20R / TKC-20R; Revised: 05/02/23
Page 8 of 48
The shape, holes, and
copper-colored stud indicate this
is not a Genuine Subaru inflator.
NOTE: Some models utilize a “tether clip” to secure the upper portion of the “A” pillar trim. The
tether clip is located just below where the “A” pillar trim meets the head liner. If the tether clip
becomes damaged, it MUST be replaced. The illustrations and photos below show the location of the
tether clip and how to release it. It is STRONGLY RECOMMENDED to use the release tool (p.n.
SOA635147) specifically designed for tether clip removal. Each Retailer has been supplied with 2 of
these tools. If the tool is unavailable, a needle-nosed plier can be used to CAREFULLY release the
tether clip as shown in the illustration below.
Continued...
Bulletin Number: TKA-20R / TKB-20R / TKC-20R; Revised: 05/02/23
Page 9 of 48
Carline
IMPREZA
WRX
LEGACY
OUTBACK
Legacy
Outback
Baja
Type
• If the color of the collar is Pink, it is a ZF
TRW inflator.
• If no collar is found, it is a Takata inflator.
2) Check for the inflator collar from the bottom
(TIP: use a Mechanic’s mirror to make it
easier).
1) Release the stoppers of the glovebox and
open it fully.
IMPORTANT: For 2003MY ONLY see
Appendix B on page 47 for more
information.
• If the color of the collar is Pink, it is a ZF
TRW inflator.
• If no collar is found, it is a Takata inflator.
2) Check the inflator collar inside the IP.
1) CAREFULLY remove the air conditioning
vent duct on the passenger side.
• If the color of the collar is Pink, it is a ZF
TRW inflator.
• If no collar is found, it is a Takata inflator.
2) Check the inflator collar from the bottom
backside of the instrument panel (IP) on the
passenger side.
1) For these models, there is no need to
remove any parts.
Procedure / How to Identify
ZF TRW
End Collar
Color
Pink
Pink
Pink
Pink
ZF TRW: OK - Do NOT replace the Inflator
or Module Assembly. Process Claim for
INSPECTION ONLY.
Using a Mechanic’s
Mirror to confirm the
NG inflator.
TAKATA: NG - Replace the Inflator or
Module Assembly per the table.
INSPECTION: How To Determine if the Installed Inflator Is Takata or ZF / TRW
Part
Number
Inflator
Module
Inflator
Module
98279FE070
98279FE07A
98279FE12A
98279FE12B
98279AG05B
98279AE04A
98279AE04B
Page 10 of 48
Bulletin Number: TKA-20R / TKB-20R / TKC-20R; Revised: 05/02/23
Model
Years
2004-05MY
2006-07MY
2005-09MY
2003-06MY
TIP: In some cases, removal of the module
/ dash cover assembly from the IP may be
easier and quicker.
Continued...
Model
Years
2008-14MY
2009-13MY
2010-14MY
Carline
IMPREZA
WRX
FORESTER
LEGACY
OUTBACK
Part
Number
98279FG07A
98279FG07B
98279SC05A
98279SC05B
98279AJ06A
Type
Module
Module
Module
Procedure / How to Identify
1) CAREFULLY remove the end panel of the
IP on the passenger side.
2) Check the inflator collar inside the IP.
• If the color of the collar is Pink, it is a ZF
TRW inflator.
• If no collar is found, it is a Takata inflator.
1) CAREFULLY remove the end panel of the
IP on the passenger side.
2) Check for the inflator collar inside the IP.
• If the color of the collar is Pink, it is a ZF
TRW inflator.
• If no collar is found, it is a Takata inflator.
1) CAREFULLY remove the end panel of the
IP on the passenger side.
2) Check the harness connector color of the
inflator inside the IP.
• If the connector is Black/Yellow, it is a ZF
TRW inflator.
• If the connector is Solid Yellow, it is a
Takata inflator.
ZF TRW
End Collar
Color
Pink
Pink
No End
Collars Are
Used
ZF TRW: OK - Do NOT replace the Inflator
or Module Assembly. Process Claim for
INSPECTION ONLY.
Harness connector is a
combination of Black and Yellow.
TAKATA: NG - Replace the Inflator or
Module Assembly per the table.
Harness connector
is Solid Yellow.
Page 11 of 48
Bulletin Number: TKA-20R / TKB-20R / TKC-20R; Revised: 05/02/23
*SERVICE PROCEDURE FOR 2010-14MY LEGACY / OUTBACK MODELS*
Replacement Airbag Module Assembly Part Number: 98279AJ06A
CAUTION: Refer to the “CAUTION” section in the General Description portion of Airbag
System AB in the Body Section of the Service Manual before handling or servicing any airbag
module!
STEP 1- PREPARATION:
• Record the customer’s radio station presets (and Navigation favorites where applicable).
• Turn the ignition “OFF”.
• Disconnect the Negative (ground) cable from the battery and wait at least 60 seconds before
proceeding further.
• Follow the procedures in the applicable Service Manual for removing the instrument panel
assembly as required to access the passenger side airbag module.
• Disconnect the wiring harness and remove the airbag module.
IMPORTANT: Whenever beginning to remove (or install) the airbag assembly, and periodically
while performing the procedure or after stepping away, remove any possible static charge
from your body by momentarily touching a clean, bare metal ground point on the vehicle (e.g.
the door striker). Remove from your person all electronic devices including cell phones before
proceeding.
IMPORTANT: DO NOT destroy or damage the Shipping Box as it MUST be used for the
original module’s return shipping.
STEP 2- To access the passenger’s airbag module, the complete instrument panel assembly must be
removed. Follow the procedures in the applicable Service Manual for removing the instrument panel
assembly in addition to the necessary related interior trim components.
NOTE: When removing the “A” pillar trim, be VERY CAREFUL not to damage the upper trim
retaining (tether) clip. The clip is located just below where the trim panel meets the head liner. If the
tether clip becomes damaged, it MUST be replaced. The illustrations below show how to release the
tether clip and remove the “A” pillar trim. It is STRONGLY RECOMMENDED to use the release
tool (p.n. SOA635147) specifically designed for tether clip removal. See pg. 8 of this bulletin for
more information.
Once the instrument panel assembly has been removed from the vehicle, CAREFULLY release the
retaining claws and separate the airbag bag module.
Continued...
Bulletin Number: TKA-20R / TKB-20R / TKC-20R; Revised: 05/02/23
Page 12 of 48
STEP 3- Install the new airbag module to the instrument panel.
STEP 4- Reinstall the instrument panel assembly into the vehicle in reverse order of disassembly.
Once the negative battery cable has been reconnected, turn the ignition key “ON” and confirm the
AIRBAG warning light comes on then cycles off properly. Once proper warning light operation is
confirmed, reinstall the remaining components and reset the radio station presets (and Navigation
favorites where applicable) to complete the procedure.
STEP 5- If not already done, place the removed original air bag module in the Shipping Box, with
a completed SOA warranty parts tag (MSA5W1901A) attached to it. The tag must contain the
following information: Claim Number, Repair Date, 17-digit VIN, and vehicle mileage. Refer to
the “PART RETURN PROCEDURES” section of this bulletin for further return shipping instructions
and information. Ensure both the removed and installed module serial numbers have been
recorded correctly as previously instructed on the repair order hard copy before returning the
removed part to your Parts Department.
IMPORTANT: UNDER NO CIRCUMSTANCES SHOULD ANY AIR BAG INFLATORS OR
MODULE ASSEMBLIES BE RETURNED TO SUBARU OF AMERICA, INC.
Continued...
Bulletin Number: TKA-20R / TKB-20R / TKC-20R; Revised: 05/02/23
Page 13 of 48
*SERVICE PROCEDURE FOR 2009-2013MY FORESTER and 2008-2011MY IMPREZA and
2008-2014 MY WRX and STI MODELS* Replacement Airbag Module Assembly Part Number
98279FG07B (Impreza, WRX and STI) and 98279SC05B (Forester)
CAUTION: Refer to the “CAUTION” section in the General Description portion of Airbag
System AB in the Body Section of the Service Manual before handling or servicing any airbag
module!
STEP 1- PREPARATION:
•
Record the customer’s radio station presets (and Navigation favorites where applicable).
•
Turn the ignition “OFF”.
•
Disconnect the Negative (ground) cable from the battery and wait at least 60 seconds before
proceeding further.
•
Follow the procedures in the applicable Service Manual for removing the instrument panel
assembly as required to access the passenger side airbag module.
•
Disconnect the wiring harness and remove the airbag module.
IMPORTANT: Whenever beginning to remove (or install) the airbag assembly, and periodically
while performing the procedure or after stepping away, remove any possible static charge
from your body by momentarily touching a clean, bare metal ground point on the vehicle (e.g.
the door striker). Remove from your person all electronic devices including cell phones before
proceeding.
IMPORTANT: DO NOT destroy or damage the Shipping Box as it MUST be used for the
original module’s return shipping.
STEP 2- To access the passenger’s airbag module, the complete instrument panel assembly must be
removed. Follow the procedures in the applicable Service Manual for removing the instrument panel
assembly in addition to the necessary related interior trim components.
NOTE: On FORESTER models, when removing the “A” pillar trim, be VERY CAREFUL not to
damage the upper trim retaining (tether) clip. It is STRONGLY RECOMMENDED to use the release
tool (p.n. SOA635147) specifically designed for tether clip removal. See pg. 8 of this bulletin for
more information. The clip is located just below where the trim panel meets the head liner. If the
tether clip becomes damaged, it MUST be replaced. The illustrations below show how to release the
tether clip and remove the “A” pillar trim.
On IMPREZA models, in place of the tether clip, the trim is secured by a screw accessible by
removing the small access cover.
Continued...
Bulletin Number: TKA-20R / TKB-20R / TKC-20R; Revised: 05/02/23
Page 14 of 48
Once the instrument panel assembly has been removed from the vehicle, CAREFULLY release the
retaining claws and separate the airbag bag module.
STEP 3- Install the new airbag module to the instrument panel.
STEP 4- Reinstall the instrument panel assembly into the vehicle in reverse order of disassembly.
Once the negative battery cable has been reconnected, turn the ignition key “ON” and confirm the
AIRBAG warning light comes on then cycles off properly. Once proper warning light operation is
confirmed, reinstall the remaining components and reset the radio station presets (and Navigation
favorites where applicable) to complete the procedure.
STEP 5- If not already done, place the removed original air bag module assembly in the Shipping
Box (or into the returnable shipping box), with a completed SOA warranty parts tag (MSA5W1901A)
attached to it. The tag must contain the following information: Claim Number, Repair Date,
17-digit VIN, and vehicle mileage. Refer to the “PART RETURN PROCEDURES” and Appendix
“A” sections of this bulletin for further return shipping instructions and information. Ensure both
the removed and installed module serial numbers have been recorded correctly as previously
instructed on the repair order hard copy before returning the removed part to your Parts
Department.
IMPORTANT: UNDER NO CIRCUMSTANCES SHOULD ANY AIR BAG INFLATORS OR
MODULE ASSEMBLIES BE RETURNED TO SUBARU OF AMERICA, INC.
Continued...
Bulletin Number: TKA-20R / TKB-20R / TKC-20R; Revised: 05/02/23
Page 15 of 48
*SERVICE PROCEDURE FOR 2003-2004MY LEGACY / OUTBACK AND
2003-2006MY BAJA MODELS* Replacement Airbag Module Assembly Part Number: 98279AE04A
IMPORTANT: For 2003MY vehicles ONLY, see Appendix B on page 47, BEFORE proceeding.
IMPORTANT NOTES:
The new module assembly does not include the lid (outer trim cover). In this procedure, the lid is
transferred to the new module from the original. In an extremely rare case where a lid gets damaged
during the transfer, part numbers for replacements are provided below.
Description
AIR B MOD P KIT LID
Part Number
Color
98279AE05ADG
Brown
98279AE05AML
Black
CAUTION: Refer to the “CAUTION” section in the General Description portion of Airbag
System AB in the Body Section of the Service Manual before handling or servicing any airbag
module!
STEP 1- PREPARATION:
Before proceeding, confirm the airbag lamp cycles on and then off normally as part of the self-check
and using SSM, confirm there are no DTCs stored in the airbag system. Inspect the dash area around
the passenger airbag module for any marks or damage. Document and photograph any conditions
observed before starting this procedure.
• Turn the ignition “OFF”.
• Disconnect the Negative (ground) cable from the battery and wait at least 60 seconds before
proceeding further.
• Remove the glove box assembly following the procedure in the applicable Service Manual
and using the tips below.
o The glove box is held in place by 8 screws. The 2 upper left and right hand corner screws
have a distinctive gold finish and 10mm hex head. It is helpful to leave these 2 screws
until last when removing and install first during replacement to support the weight of the
assembly.
o It is necessary to remove the knockout plugs (stopper in the Service Manual) to gain
access to all the mounting screws.
•
o It is possible to leave the stoppers in place during servicing by carefully bending in the
sides of the glove box until the stoppers are cleared.
To prevent damage, do not bend them in any further than necessary.
IMPORTANT: Whenever beginning to remove (or install) the airbag assembly, and periodically
while performing the procedure or after stepping away, remove any possible static charge from
your body by momentarily touching a clean, bare metal ground point on the vehicle (e.g. the
door striker). Remove from your person all electronic devices including cell phones before
proceeding.
Continued...
Bulletin Number: TKA-20R / TKB-20R / TKC-20R; Revised: 05/02/23
Page 16 of 48
•
Disconnect the airbag module harness
connector (A) and release it from the support
beam bracket.
•
Remove the 3 retaining bolts and
CAREFULLY remove the airbag module
from the vehicle by carefully releasing the
cover tabs from the underside of the dash and
pushing the module up and out. Use caution
and protective coverings to avoid damaging the dashboard pad. Place the airbag module on a
clean cloth to protect the module lid from scuffs, scratches or other damage.
STEP 2- TRIM COVER / LID REMOVAL:
VERY IMPORTANT: Before removing the original
trim cover / lid from the module, note the orientation
of the cover in relation to the module as the module can
be installed upside down in the cover. (TIP: The bottom
or harness side goes toward the “SRS AIRBAG” side of the
cover as shown.)
CAUTION: During cold temperatures always let the cover
warm to room temperature before attempting claw removal.
In all cases, limit any distortion of the airbag cover to avoid
damaging it.
•
•
Using a trim clip removal tool and starting on the harness-side of the module assembly as
shown in the sequence below, CAREFULLY insert the tool and twist ONLY AS MUCH AS
IS REQUIRED to release the slightly longer center retaining claw from the trim cover. Once
released with the tool, the other 6 claws will release easily by hand.
Rotate the inflator portion of the assembly outward from the cover to release the 7 label-side
claws and separate the cover from the module. No tool is required as all the 7 label-side
claws are the same size.
Serial Number
FIGURE1
Continued...
Bulletin Number: TKA-20R / TKB-20R / TKC-20R; Revised: 05/02/23
Page 17 of 48
Twisting the Tool and
Releasing Center Claw
Trim Clip Removal
Tool Inserted
Center Claw Released
All Harness-Side Claws Released
Serial Number
OK
Close-up of a witness mark left
behind by the inside of the center
retaining claw. This is normal and
acceptable. There is no need to
replace the cover for this.
Inside view of a damaged
cover, shows tearing and
material missing. This cover
must be replaced.
Step 3- Confirm the orientation is correct as outlined earlier in this bulletin. Refit the original
cover, if reusable, onto the replacement module assembly. Make sure all the claws are fully engaged
(see Figure 1 above). When properly installed, the cover should feel loose with a small amount of
freeplay. If the cover is tight (no freeplay or looseness), it most likely is not fully engaged onto the
claws.
Continued...
Bulletin Number: TKA-20R / TKB-20R / TKC-20R; Revised: 05/02/23
Page 18 of 48
Step 4- VERY IMPORTANT: Record the alpha-numeric serial numbers for BOTH the original
and the replacement module assemblies on the hard copy of the Repair Order. See pages 17 & 18
for serial number location photos. For SOA and SDC Retailers ONLY, this information will be
required for claim approval. For SNE retailers, this information will be required for completion of
the Part Return Notice which will be forwarded by the retailer to the PCC.
Step 5- After confirming the cover is properly fitted to the module, reinstall the module assembly
in reverse order of disassembly. Before installing the glove box assembly, reconnect the negative
battery cable. Turn the ignition key “ON” and confirm the AIRBAG warning light comes on then
cycles off properly. Once proper warning light operation is confirmed, reinstall the glove box
assembly.
Step 6- Place the removed module assembly into the returnable shipping box. Refer to the
SHIPPING DOCUMENTATION AND INSTRUCTIONS (Appendix A) found toward the end of
this bulletin.
IMPORTANT: UNDER NO CIRCUMSTANCES SHOULD ANY AIRBAG MODULES BE
RETURNED TO SUBARU OF AMERICA, INC.
Continued...
Bulletin Number: TKA-20R / TKB-20R / TKC-20R; Revised: 05/02/23
Page 19 of 48
*SERVICE PROCEDURE FOR 2005-2009MY LEGACY / OUTBACK MODELS*
Inflator Type 2, Inflator Kit Part Number: 98279AG05A or B
CAUTION: Refer to the “CAUTION” section in the General Description portion of Airbag
System AB in the Body Section of the Service Manual before handling or servicing any airbag
module!
STEP 1- PREPARATION:
•
•
•
•
•
•
Record the customer’s radio station presets (and Navigation favorites where applicable).
Turn the ignition “OFF”.
Disconnect the Negative (ground) cable from the battery and wait at least 60 seconds before
proceeding further.
Follow the procedures in the applicable Service Manual for removing the instrument panel
assembly as required to access the passenger side airbag module.
Disconnect the wiring harness and remove the airbag module.
Secure the removed airbag module to the Airbag Deployment Fixture (part number
J-39401-B).
IMPORTANT NOTE: The photos available at the time of this procedure’s preparation do not show
the removed airbag module assembly as being secured to the J-39401-B Airbag Deployment Fixture
during inflator replacement. Subaru of America, Inc. STRONGLY RECOMMENDS ALWAYS utilizing a J-39401-B fixture whenever performing ANY airbag inflator replacement service procedure.
IMPORTANT: Whenever beginning to remove (or install) the airbag assembly, and periodically
while performing the procedure or after stepping away, remove any possible static charge
from your body by momentarily touching a clean, bare metal ground point on the vehicle (e.g.
the door striker). Remove from your person all electronic devices including cell phones before
proceeding.
IMPORTANT: DO NOT destroy or damage the Kit Box as it MUST be used for the original
inflator’s return shipping.
Open the Kit Box and confirm all the necessary components
are included:
•
4 Self-Locking nuts
•
New Type 2 Inflator (pink collars on each end identify it as the replacement part)
•
New Inflator Harness
•
1 new Stopper Plate (A)
•
Heat Insulating Plate
- 💯【Conta.ct us for Support Directly】If you met any...
- 🔥🔥🔥【2026 AUTEL FLAGSHIP MK900BT MK900-BT, NEW...
- 🚗【3000+ ACTIVE TESTS (50➡3000+), SAME AS MS...
- 🚗【40+ HOT SERVICES FOR 150 MAKES (28+➡40+)】Full...
- 🚗【OE ALL SYSTEM DIAGNOSE, AUTO SCAN 2.0: SCAN LICENSE...
- 【TURN OFF CEL】 This AL319 car scanner diagnostic tool...
- 【EXTENSIVE APPLICATION】 Autel AL319 Compatible with...
- 【FOR END USER & DIYERS】 This error code reader AL319 is...
- 【USER-FRIENDLY DESIGN】 This OBD2 scanner and check...
- 【HIGH-QUALITY SERVICES】 12 months war.ranty from the...
Last update on 2026-06-23 / Affiliate links / Images from Amazon Product Advertising API
If the PDF is very large, it may not load in the preview below.
Some older TSBs had multiple PDFs — visit the NHTSA Website to view all PDFs.
If the TSB PDF does not show, download or view it on the NHTSA Website.
Click on the (+) Plus Sign
Then Click on Associated Document(s)
Search NHTSA Database for Recalls
Search NHTSA Database for Vehicle Investigations
View Latest Vehicle Investigations
Search NHTSA Database for Vehicle Complaints
View Latest Vehicle Complaints
TSB/Document ID: TKA-20R,TKB-20R,
Replacement Service Bulletin Number:
MFR Communication Date: 2023-05-02
MFR Internal Campaign ID/Software Version:
Communication Type: Service Bulletin/Repair Instructions
NHTSA Components: ELECTRICAL SYSTEM
MFR Component System:
MFR Component Subsystem:
Previous TSB | Next TSB |
- WHY CHOOSE THE 2025 CR MAX -Upgrade the latest diagnostic capabilities for all vehicles after 1996: upgrade to 49+maintenance services; 46 extra specific functions; real all systems/all control modules diagnose; over 40K+ bidirectional actuation tests for diagnosing all control moduels of cars; Powerful full OBD2 Functions; built-in ECU Coding for BMW
/ Audi/ VW/ RollsRoyce; Fr ee V.A.G Guide Function; Battery retistration for new battery adaptation and more. It covers all vehicle diagnostic services and some special professional vehicle maintenance servces, assists you to do home DIY vehicle maintenance or car repair as a pro technician. - NEWEST IN INNOVATION FULL OBD2 SERVICES- iCarsoft auto car diagnostic scanner compatible with CAN-FD, CR MAX can do it all-reads and clears trouble codes, ALL SYSTEM DIAGNOSIS such as engine, transmission, ABS and airbag etc. CR MAX code reader for all cars can perform I/M Readiness, Live Data, Freeze Frame, Vehicle Information, Monitor Test, On-Board Monitor, E vap System Test,O2 Sensor Test,DTC Library Lookup,etc. (Warm Tips: If you car is after 2023,please contact us for compatibility; 3. It comes with 16PIN OBD2 diagnostic adapter, please check your car diagnostic socket if it is 16pin socket, if your car is 14pin diagnostic socket please contact us for the solution.)
- 49 RESET+ 46 SERVICES- Performs: Oil Reset, EPB,SAS,Throttle, D-P - F, Battery, ABS, Injector, TPMS, Suspension, AC, Head Lamp, Body Stablity, Engine, Tramsmission, Airbag, Seat, Door-Win-Roof, Fuel Pump, Door, E-G- R.+21 NEWEST SERVICES( Need update scanner)-AdBlue, Clutch, Crankshaft, High Voltage Battery, Cruise Control, NO xSensor, Rain Sensor, Stop And Start, Turbocharger, Head Up Display, Radar Camera, Vehicle Setup, Cyliner Misfire Check,Speedlimitassist, ControlUnitReset,OxygenSensor, Seatbelt. Extra 46+ extra services based on car brand.(Tips: Quantity of reset/ calibration fucitons are based on car system that your vehicle model has)
- REVOLUTIONARY 40000+BIDIRECTIONAL ACTIVE TESTS: Upgraded CR Max scanner equip with numberous of actuational test items for covering all available vehicle control modules, no longer only do simple light test or window test like other scanners, performs hardware modules test and software control modules test for checking car units or new updated control moduels work well or not after maintenance/ repair/ re-installation/ control system updated (Example for Benz- Roller Sun Blind test; Backup Camera test ;Self-test; EPB test; Transport Mode test;Boost Pressure Positioner test; Fuel Pump test; AND MORE!!).(Warm tip: The available test items are based on control modules your car has)
- ECU CODING+ BATTERY REGISTRATION- Powerful ECU Coding service for BMW/MINI/RollsRoyce / Audi/VW/Seat/Skoda/Bentley/Bugatti/Lamborghini, Improves Engine Power Performance and Optimizes Fuel Efficiency and Match New Hardware Unit to car and Customized a comfortable Driving Modes and Fixes & Updates Original Software Bug. The battery test function for checking car battery health, perform battery reset (BMS ) for replacing a damaged or aging car battery with a new one and register new battery to car ECU
- 【Looking for More Professional Vehicle Scan Tool?】iCarsoft E660 2026 Upgrade Version OBD2 scan tool can do it all-reads and clears trouble codes on Engine system, ABS system, Transmission system and Airbag system, And with 6 reset function. It covers more than 59 vehicle makes from 1996-2023 models ( included most USA/ Asia / EU vehicle brand) with full OBDII. (As every car model has its-owned specific car system and ECUs, not all car models have full car ECUs which may prevent the scanner from performing all listed system diagnostics or reset services. Therefore, please email to us with car VIN and services required to do scanner's services for a compatibility check before purchasing.)
- 【OE-Level 4 Systems OBD2 Scanner】iCarsoft E660 2026 Upgrade Version diagnostic scanner offers comprehensive OBDII services, allowing you to quickly scan Engine system. It supports functions such as reading and erasing codes, checking I/M readiness, viewing freeze frame data, performing O2 sensor tests, conducting on-board monitoring, testing the evap system, auto VIN retrieval, and reading both generic and specific codes, as well as DTCs and battery tests.
- 【4 Systems Diagnosis for 10000+ Vehicles】 iCarsoft E660 2026 Upgrade Version adopts unique diagnostic software, works well for most Porsche, Benz, BMW, US Ford, Land Rover, Jaguar, Audi, VW, Volvo, Honda, Nissan, Infiniti, Toyota, Lexus, Scion, Isuzu, Hyundai, Kia, Daewoo, Mazda, Sprinter, Mini, Seat, Skoda, SAAB, EU Ford, Holden, AUS Ford, Acura, Subaru, Mitsubishi, Dacia, Renault, Fiat, GM, Chrysler, Citroen, Peugeot, Opel, Smart,Suzuki, Vauxhall, Alfa-Romeo, Lancia and etc.
- 【6 Reset Services】iCarsoft E660 2026 Upgrade Version is a diagnostic tool that offers professional maintenance services, including Oil Reset, EPB, BMS, ETC, SAS, TPMS Reset. It can help you easily reset oil change indicators, recalibrate steering angle sensors, relearn replaced electric parking brake and so on. For optimal vehicle performance and maintenance convenience. (Tips: Please update the softwareafter receiving the product to obtain new service functions)
- 【118+ Real Time Record & Live Graph View】iCarsoft E660 2026 Upgrade Version can automatically record vehicle text history and identify vehicle information. Preserve real-time data information. View & Graph Live Data. Support Data Review and Print. 15 languages: English, German, Dutch, Spanish, French and so on. We promise to offer Lifetime updates (Lifetime free Update via PC), and confidence in products. We also provide 1 year warranty + extra lifetime hardware free repair if you need it in the future. We prioritize user experience & strive to meet your expectations. Please do feel free to reach out to us if you have any question or problem about the usage.
- 【All-in-One Diagnostic Tool for Porsche + 2 Extra Vehicle Brands】New POR V4.0 is a professional car scanner specifically engineered with dedicated software pre-installed for Porsche. You can also download 2 additional software packages FOR FREE from 26 supported brands (e.g., for Benz, for BMW, for Audi, for Land Rover).Upgraded to adopt quad-core 1.3GHz processor and HD touchscreen and professional diagnsotic OS for faster& smooth diagnsotic.LIFETIME FREE UPDATES, NO SUBSCRIPTION COST! PLEASE TELL US YOUR CAR INFORMATION TO OBTAIN A LIST OF ALL COMPATIBLE SERVICES FOR YOUR CAR FIRST (FOR EXAMPLE: BATTERY REGISTRATION FUNCTION IS NOT COMPATIBLE WITH PORSCHE 997.2)
- 【29 MAINTENANCE SERVICES FOR PORSCHE SERIES CARS】 It can perform the 29 reset service for Porsche series cars-Oil Reset; SAS; EPB; BMS; ETC; DP ; ABS Bleeding; Injector Coding; TPMS; Air Suspension; Air Conditioner; Head Lamp; Body Stablity Control; Engine Control; Transmission; AirBag; Seat; DWR; MIS; EG; ODO; Clutch; High Voltage Battery; Cruise Control; Radar/Camera; Vehicle Setup,etc. Up to 49 vehicle-maintenance-services for the extra 2 vehicle brands you installed (Tip: Not all services will be worked on every car mode. Some vehicle models may be lack of certain ECU-control modules to make some services may not work).
- UPGRADE SERVICES: Breaks down 29 services to 234 sub-service for car owners/machinist to perform maintenance based on corresponding sub-modules! The detailed sub-service for sub-modules assist to perform precise vehicle maintenance.Improving the accuracy of car maintenance and reducing potential failure risks caused by whole-module maintenance to main modules.such as Oil Reset is refined into Reset maintenance interval/Reset service interval/Service Reset; Engine Control Reset is refined into Delete adaptation data/Short tests/System tests/Swirl-flap actuator/Bleeding high temperature coolant circuit and more.（sub-services vary based on vehicle model/year）
- 【EXTRA VEHICLE MAINTENANC SERVICES FOR SPECIFIC SYSTEMS】Have no ability to perferm calibration to special/specific systems/modules? This OBD2 scanner solve your troubles- for common systems/modules & for specific sytems/modules, assist you to perform diagnsing/calibration/reset/relearn services for non-common modules to finish your car maintenance/ diagnostic (eg: Central Computer system/module :Function activation/Multimedia interface test/AM Field Strength/Current FM Field Strength/FM Field Strength/MOST system reserve/Self-test/Deactivate Production Mode/Reset to factory settings/MOST System Test). (Tip: The services vary based on the vehicle brands)
- 【 MORE PROFESSIONAL BI-DIRECTIONAL ACTUATION TESET 】Exclusive POR V4.0 comes with powerful bidirectional testing capability,do actuaction test for deeper unit-checking after replacement or overhaul (1333 test items for Porsche, like:Fuel high-pressure fuel injector 1-4, Empty tank, Radiator fan, OTA-FC Connectivity, backrest, Backup battery, and more; 2136 test items for Audi; 1670 test items for Benz; 1599 test items for Volvo; 1360 test items for VW; 2705 test items for GM etc.). Help to check your car units work well or not after vehicle maintenance or daily car-body check, keep drives always in safety.(Warm tip:The quantity of test item is based on the units your car has)
Last update on 2026-06-23 / Affiliate links / Images from Amazon Product Advertising API
This product presentation was made with AAWP plugin.