BASIC INSPECTION > INSPECTION AND ADJUSTMENT > ADDITIONAL
SERVICE WHEN REMOVING BATTERY NEGATIVE TERMINAL, for a listing of
systems that require reset/initialization after reconnecting the 12V battery.



This list often includes items such as radio, power windows, clock, sunroof, etc.

Proceed to the next page.

109/152

NTB22-021A

Additional Service When Replacing Control Valve Or Transaxle Assembly

The following procedures, starting on the next page, must be performed in this order:

a. TCM Reprogramming (if applicable)…………..…….……….…..…….Page 111
b. CONTROL VALVE REPLACEMENT..…..…………………...……….….Page 131
c. ERASE LEARNING VALUE……..………….………………..……..…….Page 136
d. CONFORM CVTF DETERIORTN…………………….…….………….….Page 138
e. AUXILIARY GEARBOX CLUTCH POINT LEARNING…….……...……Page 141
f. ERASE DTCS………………………………………………………….…….Page 143

Proceed to the next page.

110/152

NTB22-021A

TCM Reprogramming
IMPORTANT: Repairs performed for this bulletin require CONSULT Diagnostic result
reporting function-Setting be turned ON and Diagnosis (All Systems) be performed. If not
done, it may result in a repair being non-warrantable.
IMPORTANT: Before starting, make sure:



HINT:

206.

ASIST on the CONSULT PC has been synchronized (updated) to the current
date.
All C-III plus software updates (if any) have been installed.
The CONSULT PC is connected to the Internet (Wi-Fi or cable).



Most instructions for reprogramming with C-III plus are displayed on the
CONSULT PC screen.



If you are not familiar with the reprogramming procedure, click here. This will
link you to the "CONSULT Reprogramming for Engine or Transmission Control
Module (ECM or TCM)" general procedure.

Connect the Vehicle Interface (VI) to the vehicle.
Make sure the VI is securly connected. If the VI connection is loose during
reprogramming, the process will be interrupted and the TCM may be damaged.

207.

Connect the AC Adapter to the CONSULT PC.
Be sure to connect the AC Adapter. If the CONSULT PC battery voltage drops
during reprogramming, the process will be interrupted and the TCM may be
damaged.

208.

Connect a battery maintainer or smart charger, set to reflash mode or a similar
setting, to the vehicle battery.
Be sure the battery maintainer or smart charger is connected securely to the
battery. Make sure the battery voltage stays between 12.0V and 15.5V during
reprogramming. If the battery voltage goes out of this range during
reprogramming, the TCM may be damaged.

209.

Turn OFF all external Bluetooth® devices (e.g., cell phones, printers, etc.) within
range of the CONSULT PC and the VI.
Make sure to turn OFF all external Bluetooth® devices. If Bluetooth® signal waves
are within range of the CONSULT PC and the VI during reprogramming,
reprogramming may be interrupted and the TCM may be damaged.

111/152

NTB22-021A

210.

Turn the ignition ON with the engine OFF.


211.

The engine must not start or run during the reprogramming procedure.

Turn OFF all vehicle electrical loads such as exterior lights, interior lights, HVAC,
blower, rear defogger, audio, NAVI, seat heater, steering wheel heater, etc.
Make sure to turn OFF all vehicle electrical loads. Make sure the battery voltage
stays between 12.0V and 15.5V during reprogramming. If the battery voltage goes
out of this range during reprogramming, the TCM may be damaged.

212.

Connect the CONSULT PC to the vehicle to begin the reprogramming procedure.

213.

Start C-III plus.

214.

If prompted, select USA/CANADA Dealers from the drop down menu, and then
select OK.

215.

Login using your NNAnet credentials.
IMPORTANT: If not prompted to enter your username and password, the CONSULT
PC may not be connected to Wi-Fi. Close C-III plus, confirm the CONSULT PC is
connected to Wi-Fi, and then reopen C-III plus.

216.

Wait for the VI to be recognized.


217.

The serial number will display when the VI is recognized.

Select Re/programming, Configuration.

VI is
recognized

Figure 232
112/152

NTB22-021A

218.

Use arrows (if needed) to view and read all precautions.

219.

Check the box confirming the precautions have been read.

220.

Select Next.

Figure 233

113/152

NTB22-021A

221.

If the screen in Figure 234 displays, select Automatic Selection(VIN).


If the screen in Figure 234 does not display, continue to step 222.

Example

Figure 234

222.

Make sure VIN or Chassis # matches the vehicle’s VIN.

223.

If the correct VIN is displayed, select Confirm.

xxxxxxxxxxxxxxxxx
xxxxx
xxxx

Figure 235

114/152

NTB22-021A

224.

Select Confirm.

xxxxxxxxxxxxxxxxx

Figure 236

225.

Select TRANSMISSION.

Figure 237

115/152

NTB22-021A

226.

Select Reprogramming.

Figure 238
227.

Follow the on-screen instructions; maintain the following conditions:
a. Turn the ignition ON with the engine OFF.
b. Press the brake pedal.
c. Press the accelerator pedal between ¼ and ½.
d. Put the shift selector in R.

228.

Select Start.

Figure 239
116/152

NTB22-021A

229.

When “COMPLETED” is displayed, select Next.

Figure 240

230.

Operate the ignition per the on screen instructions.

Ignition status

Timer
Progress display

Figure 241

117/152

NTB22-021A

231.

When “OK” is displayed, select Next.

Figure 242

232.

Move the shift selector to P, then select Next.

Figure 243

118/152

NTB22-021A

233.

Operate the shift selector per the on screen instructions.
a. Move the shift selector; P>R>N>D>P
b. Confirm the center display meter indicates the correct selector position.

234.

Select Next.

Figure 244

235. Find the TCM Part
Number (Figure 245) and
write it on the repair order.
HINT: This is the current
Part Number (P/N).
236. Compare the P/N you
wrote down to the numbers
in the Current TCM Part
Number column in Table B
on page 120.

xxxxxxxxxxxxxxxxx

xxxxx
xxxxx
xxxxxxxxxxxxxxxxx
xxxxx xx xxx xxxxxx

Figure 245

119/152

NTB22-021A

237.

Comparison results:


If there is a match, continue with the reprogramming procedure.



If there is not a match, reprogramming is not needed. Skip to step 266 on
page 131.

Table B
MODEL

Kicks

Versa
(1)

YEAR
2018
2019

CURRENT TCM PART NUMBER: 31036 5RD0A, 5RD0C
5RR2A, 5RR2B, 5RR2C, 5RR2D

2020

(1)

2021

(1)

2022

(1)

2020

(1)

2021

(1)

2022

(1)

TCM reprogramming not currently applicable.

238.

Select Save.

239.

Use arrows (if needed) to view and read all precautions.

240.

Check the box confirming the precautions have been read, and then select Next.

Figure 246
120/152

NTB22-021A

241.

Read the Current Part Number and Part Number After Reprogramming. They
should be different.

242.

Select Next.

xxxxx-xxxxx
xxxxx-xxxxx
xxxxxxxxxxx

These numbers
should be
different

xxxxxxxxxxxxxxxxx

xxxxxxxxxxxxxxxx

Figure 247
243. Make sure OK is highlighted green (battery voltage must be between 12.0 and 15.5
Volts).
244.

Select Next.
IMPORTANT: Battery voltage must stay between 12.0 and 15.5 Volts during
reprogramming or TCM reprogramming may be interrupted and TCM may be
damaged.

Monitor battery
voltage here

Figure 248
121/152

NTB22-021A

HINT: In the next step, the reprogramming process will begin when Start is selected.

245.

Select Start.

Figure 249

246.

Wait for both progress bars to complete.

Figure 250

122/152

NTB22-021A

247.

When the screen in Figure 251 displays, the reprogramming is complete.
HINT: If the screen in Figure 251 does not display (which indicates reprogramming
did not complete), skip to TCM RECOVERY on page 130.

248.

Disconnect the battery maintainer/smart charger from the vehicle.

249.

Select Next.

Figure 251

HINT: Additional steps/operations are required before C-III plus will provide the final
reprogramming confirmation report. Continue to step 250 on page 124 to complete
the reprogramming procedure.

123/152

NTB22-021A

250.

Confirm the Transmission Fluid temperature judgment is “OK”, then select Next.


If the judgement is “NG”, drive the vehicle to warm the transmission until the
judgement changes to “OK”.

Figure 252

124/152

NTB22-021A

251.

Follow the on-screen
instructions while
maintaining the following
conditions:
a. Parking brake set.
b. Turn the ignition ON,
with the engine OFF.
c. Press the brake
pedal.
d. Press the accelerator
pedal between ¼ and
½.

Figure 253

e. Put the shift selector
in R.
252.

Select Erase DTC.

253.

Follow the on-screen
instructions while
maintaining the following
conditions:
a. Parking brake set.
b. Ignition ON, with the
engine OFF.
c. Fully depress the
accelerator pedal.
d. Put the shift selector in
R.
Figure 254

254.

Select Start.

125/152

NTB22-021A

255.

When “COMPLETED” is displayed, select Next.

Figure 255

256.

Operate the ignition per the on-screen instructions.

Ignition status

Timer
Progress display

Figure 256

126/152

NTB22-021A

257.

When “OK” is displayed, select Next.

Figure 257

258.

Operate the shift selector per the on-screen instructions.
a. Move the shift selector to P, then move P>R>N>D>P.
b. Confirm the center display meter indicates the correct selector position.

259.

Select Next.

Figure 258

127/152