Technical product information
Topic
Market area
Brand
Transaction No.
Level
Status
Release date

Bentayga - 1.2KHz - 1.4KHz rear brake squeal
Bentley: worldwide (2WBE)
Bentley
2046299/16
EH
Approval

New customer code
Object of complaint

Complaint type

Position

running gear -> brakes, brake control -> service brake noise, vibration -> noise
New workshop code
Object of complaint
Complaint type
Position
running gear -> brake system -> brake pads (disc brake) noise, vibration -> noise rear left
running gear -> brake system -> brake pads (disc brake) noise, vibration -> noise rear right

Vehicle data
Bentayga series
Sales types
Type MY Brand Designation Engine code Gearbox code Final drive code
4V1*
4V1*
4V1*
4V1*
4V1*
4V1*
4V1*
ZV1*

2017
2018
2019
2020
2021
2022
2023
2023

E
E
E
E
E
E
E
E

Documents
Document name
master.xml

INTERNAL

*
*
*
*
*
*
*
*

*
*
*
*
*
*
*
*

*
*
*
*
*
*
*
*

Technical product information
Bentayga - 1.2KHz - 1.4KHz rear brake squeal

Transaction No.: 2046299/16

Customer statement / workshop findings
Squeal from the rear of the vehicle at low speed while braking

Technical background
While braking at low speed, a vibration of 1.2 to 1.4 KHz can be produced by the friction between the rear brake pad and disc resulting in a
complaint of brake noise from the customer

Production change
In the event the issue is evident post the following VIN’s please raise a DISS query and await feedback before conducting any further work
Bentayga standard wheel base
Black Calliper - SJAA514VXPC018789
Red Calliper - SJAAT2ZV6PC018986
Bentayga extended wheel base
Black Calliper - SJAH514V0PC018914
Red Calliper - SJAHT2ZV2PC019003

Measure
1) Follow the ‘Brake noise identification’ TPI 2052785 - IMPORTANT: For frequency analysis the noise recording equipment Bentley Motors
recommends is the Chassis ear tool WT 10437
2) If the sound recording produces a frequency of 1.2-1.4KHz - Remove the rear brake pads as per Repair manual Rep.Gr 46 - Rear Brake Pads
- To Remove and Fit and check the actual condition of the brake pads - If the brake pads are to be refitted it will be necessary to make note of
the position of the pads for installation purposes
CAUTION: The performance of the car will be affected if the brake pads are installed in the incorrect position
IMPORTANT: Prior to ordering the shim set for the rear brake pads, please ensure all required information is attached to a new or
existing DISS query including photographs of each individual brake pad and supporting evidence that the rear brake noise
frequency is between 1.2 and 1.4KHz
•

Fit the shim set 36A 698 219 to the rear brake pads (the kit consists of one shim per pad)

NOTE: G052 560 A2 “Vary Bond Regular Grade Grease”(100 gram tube) is also required to be used in conjunction with the shims
VERY IMPORTANT: The application of the grease MUST be exactly as shown/detailed, Ensuring the exact amount of grease is applied
to the locations shown

NOTE: Warranty payments for repeat repairs will not be considered if the grease is deemed to have not been applied
correctly
If new brake pads are required, photographic evidence of the pad thicknesses and the back plate of the pads must be
supplied through a DISS technical query.
IMPORTANT: The following instructions regarding grease application must also be followed regardless if the brake pads are to be replaced or
renewed
3) Carefully clean the back plate of the pad using a suitable brake cleaner IMPORTANT: Take care not to damage the rubber on the bonded
shim NOTE: In the event that the rubber is damaged from contact with the piston and there are loose rubber parts, it would be advised to fit new
brake pads.
4) The next step is to install one shim from the shim kit 36A 698 219 to each rear brake pad, ensuring that when fitted the new shim is seated
flat against the brake pad bonded shim
5) Referring to Figure 1 - Apply 6 dots of grease (< 1.0g in total) to the inside face of the clip on shim

INTERNAL

Figure 1
•

Referring to Figure 2 – Using a suitable spatula spread the grease to an even layer condition

Figure 2
6) Assemble the clip-on shim onto the pad - Squeeze together firmly to remove any excess grease which comes out from between the new shim
and the brake pad bonded shim NOTE: Ensure the new shim is seated flat against the brake pad bonded shim
•

Referring to Figures 3 and 4 Clean the pad abutments & the spring clips, then apply a small dot of grease to them

INTERNAL

Figure 3

Figure 4
7) Clean the pad abutment faces on the calliper carrier – scrape off any dirt and brake dust which has accumulated, then use a suitable brake
cleaner
8) Wipe the face of the piston to remove any brake dust or dirt.
•

Refit the rear brake pads as per Rep.Gr 46 - Rear Brake Pads - To Remove and Fit, taking care not to dis-lodge the grease/shims before
the pads are in position.

9) Carry out a road test
10) On return to the workshop, visually check for any excess grease which may have come out from between the two shims and remove with
suitable cleaner.

Warranty accounting instructions
4 Brake pads - Repaired
Warranty Type 110 or 910
Damage Service Number 46 38
Damage Code
00 20
Labour
Labour Operation Code 46 38 42 50
Time 20 Time units
4 Brake pads - Rear - Removed and Refitted

INTERNAL

Labour
Labour Operation Code 46 38 20 50
Time
50
Time
units
2 Wheels Removed and Refitted
Labour
Labour Operation Code 44 05 20 00
Time 10 Time units
Frequency diagnosis (prior to rework)
Labour
Labour Operation Code 47 01 01 00
Time
80 Time units (includes road test 01 21 00 00 - 50 Time units)
Road test (post rework)
Labour
Labour Operation Code 01 21 00 99
Time
50 Time units

Parts information
Part number Description

Quantity

36A 698 219 Shim set for rear brake pads 1 (see Notes below)
G 052 560 A2 Vary Bond grease

1 = 1 x 100 gram tube

Do not order x1 tube of grease for each individual vehicle as the grease must be used on multiple vehicles NOTE: x1 tube of
grease should be sufficient for up to 15 vehicles
Should (x1) of 36A 698 219 be ordered the retailer will receive (x4) shims as they are provided in multiples of (4) The
retailer MUST claim for the total amount of shims received,
For example: If (x1) shims are ordered, the retailer will receive (4) shims. Therefore, the retailer must claim for (4)
Please note: The shims are reusable and can be transferred over to new brake pads when required
Tip: Before transferring the shims over to new brake pads, the shims must be cleaned and inspected to confirm there are no issues
before fitment.
The operative must ensure the grease application process as detailed within the Measure section is followed
IMPORTANT: Prior to ordering the shim set for the rear brake pads, please ensure all required information is attached to a new or
existing DISS query including photographs of each individual brake pad and supporting evidence that the rear brake noise
frequency is between 1.2 and 1.4KHz

INTERNAL