BULLETIN NOTES
This bulletin supersedes the previously issued bulletin(s) listed below. The changes are noted in Red.
Previous TSBs:

Date(s) Issued:

09-001/22

11/09/22 and 01/11/22

09-026/21

09/10/21

APPLICABLE MODEL(S)/VINS
2019-2021 Mazda3 (Japan built) with VINS lower than JM1BP******404512 (produced before October 22, 2021)
2019-2022 Mazda3 (Mexico built) (produced before April 2022)
2020-2022 CX-30 (produced before May 2022)
DESCRIPTION
Some vehicles may experience white-streak stains appearing on the front door that look like they seeped out from under
the outer mirror base. This is caused by water intruding from gaps of the outer mirror body and/or the hinge of the outer
mirror, and corrosion occurring on the aluminum die-cast inner base in the outer mirror. Water, including white-salty
corrosion, may drip out from gaps under the outer mirror base resulting in white stains on the front door. To eliminate this
concern, the front outer mirror inner base has been modified.
Customers having this concern should have their vehicle repaired using the following repair procedure.

Page 1 of 10

01/03/2023 11:20 AM cciz

REPAIR PROCEDURE
1. Verify customer concern by visually inspecting the front doors under the outer mirrors for white stains. If stains seeped
out under the outer mirror are found, remove the stain(s).
2. Replace the outer-mirror inner base as follows.
NOTE: Images in this procedure show a right-side mirror
a. Remove the outer mirror according to the instructions on MGSS.
• Mazda3 (POWER OUTER MIRROR REMOVAL/INSTALLATION)
• CX-30 (POWER OUTER MIRROR REMOVAL/INSTALLATION)
NOTE: Unfold the outer mirrors before the removal.
b. Remove the seal rubber (2) and a clip (3) from the outer mirror base (1).
NOTE:
• Do not throw away the seal rubber (2), the clip (3), and the screws fastening the seal rubber, since they
should be reused.
• If there are powder and/or rust on the reused parts, wipe them off before assembling.

(1) Outer mirror base

(2) Seal rubber (3) Clip

Page 2 of 10

01/03/2023 11:20 AM cciz

c. Remove the base cover (lower) (1) from under the hinge of the outer mirror base.
NOTE: Replace the lower base cover with a new one when assembling.

(1) Base cover (lower)
(2) Hinge

Detail of the removal of the base cover (lower)

Removal of (3)

Removal of (4)

Page 3 of 10

01/03/2023 11:20 AM cciz

d. Remove the felt tape (1) and the push-nut (2).
NOTE: When assembling the inner base, replace the felt tape (1) and the push-nut (2) with new ones.

(1) Felt tape
(2) Push-nut

Page 4 of 10

01/03/2023 11:20 AM cciz

e. Remove the screws (1), then remove the inner base (2) from the outer mirror base.
NOTE: Replace the inner base with a new one when assembling.

f. Remove the harnesses (1), (2), and (3) from the inner base.
NOTE: Removal order - 1st: White (1), 2nd: Gray (2), 3rd: Brown (3)

(1) Connector: White
(2) Connector: Gray
(3) Connector: Brown

Finished to pull out

Page 5 of 10

01/03/2023 11:20 AM cciz

g. Attach a new base cover (upper) (2) to a new inner base (1).

(1) Inner base
(2) Base cover (upper)

h. Pass the harnesses through the inner base with the base cover (upper).
NOTE: Pass the harnesses through the inner base in the reverse order of pulling them out.
i. Screw the inner base to the outer mirror base.
Specified tightening torque: 4.4±0.7 ft-lb (6.0±1.0 Nm)

Page 6 of 10

01/03/2023 11:20 AM cciz

j. Route the harnesses in the correct position (1), then install a push-nut.
NOTE: When installing the push-nut, align the center of the colored tape (2) on the harness and the center of the
shaft (3).

k. Stick a felt tape to the inner base.
NOTE: When sticking the felt tape, the aluminum base should not be visible from the overlapping part (4) of the
felt tape.

(1) Start sticking here.

Stick area (2).
Stick area (3).

Stick the rest of the are
a.

l. Align the outer edges of the base cover (upper) and the base cover (lower) and assemble them so that there are
no gaps.

m. Assemble the seal rubber and the clip to the outer mirror base so that the seal rubber fits properly.
Page 7 of 10

01/03/2023 11:20 AM cciz

Specified tightening torque of the seal-rubber fastening screws: 11±1.7 in-lb (1.25±0.2 Nm)
NOTE:
• Reuse the seal rubber, the clip, and the screws fastening the seal rubber, which are removed at step 2.
• The seal rubber should not be curled and/or deformed.

n. Install the outer mirror according to the instructions on MGSS.
• Mazda3 (POWER OUTER MIRROR REMOVAL/INSTALLATION)
• CX-30 (POWER OUTER MIRROR REMOVAL/INSTALLATION)
NOTE: Unfold the outer mirrors before the removal.
3. Verify repair.

Page 8 of 10

01/03/2023 11:20 AM cciz

PARTS INFORMATION
Parts Number

Description

Qty.

Notes

BCY0-69-1AX

Base-Inner Kit (RH)

1

Mazda3 (Japan built JM1) 4-door SD

BCY0-69-1AY

Base-Inner Kit (LH)

1

Mazda3 (Japan built JM1) 4-door SD

BCY1-69-1AX

Base-Inner Kit (RH)

1

Mazda3 (Japan built JM1) 5-door HB

BCY1-69-1AY

Base-Inner Kit (LH)

1

Mazda3 (Japan built JM1) 5-door HB

BCY2-69-1AX

Base-Inner Kit (RH)

1

Mazda3 (Mexico built 3MZ) 4-door SD

BCY2-69-1AY

Base-Inner Kit (LH)

1

Mazda3 (Mexico built 3MZ) 4-door SD

DFY0-69-1AX

Base-Inner Kit (RH)

1

CX-30

DFY0-69-1AY

Base-Inner Kit (LH)

1

CX-30
Each kit includes following parts:
(1) Inner base (with electrodeposition coating)
(2) Base cover (Upper)
(3) Base cover (Lower)
(4) Felt tape
(5) Push-nut

Page 9 of 10

01/03/2023 11:20 AM cciz

WARRANTY INFORMATION
NOTE:
• This warranty information applies only to verified customer complaints on vehicles eligible for warranty repair.
• This repair will be covered under Mazda’s New Vehicle Limited Warranty term.
• Additional diagnostic time cannot be claimed for this repair.
Warranty Type

A

Symptom Code

53

Damage Code

9Y

Part Number Main Cause

****-69-1AX or ****-69-1AY

Quantity

1

Side(s)

Operation Number / Labor Hours:
(Includes: Door trim assembly, R&R)

360° view
monitor
360° view
360° view
system
monitor
monitor
screen
system
system
display
aiming
verification

Operation
No. /
Labor
Hours

Both

X

X

X

XXT4YARX
/ 2.0 Hrs.

One

X

X

X

XXT4YBRX
/ 1.1 Hrs.

Both

X

X

XXT4YCRX
/ 1.7 Hrs.

One

X

X

XXT4YDRX
/ 0.9 Hrs.

Both

XXT4YERX
/ 1.5 Hrs.

One

XXT4YFRX
/ 0.8 Hrs.

Page 10 of 10

01/03/2023 11:20 AM cciz