Classification:

Reference:

RS22-003B

Date:

NTB22-063B

August 8, 2022

VOLUNTARY SERVICE CAMPAIGN
2021 ROGUE; PASSENGER SIDE SEAT BELT RETRACTOR
AND AIRBAG MODULE
This bulletin has been amended. See AMENDMENT HISTORY on the last page.
Please discard previous versions of this bulletin.

CAMPAIGN ID #:
APPLIED VEHICLES:

P2A08
2021 Rogue (T33)

Check Service COMM or Dealer Business Systems (DBS)
National Service History to confirm campaign eligibility.

INTRODUCTION
Nissan is conducting this voluntary service campaign, on certain specific model year 2021
Rogue vehicles, to update the front passenger (RH) side seat belt retractor assembly and
airbag module, and reprogram the airbag diagnosis sensor unit. Vehicles with this update
applied were tested by NHTSA in March 2021 and received an overall safety rating of 4
stars and a front passenger safety rating of 4 stars. This is not a safety recall as all Rogue
vehicles meet all U.S. Federal Motor Vehicle Safety Standards. This service will be
performed at no charge to the customer for parts or labor.
IDENTIFICATION NUMBER
Nissan has assigned identification number P2A08 to this campaign. This number must
appear on all communication and documentation of any nature dealing with this campaign.
DEALER RESPONSIBILITY
Dealers are to repair vehicles falling within range of this campaign that enter the service
department. This includes vehicles purchased from private parties, vehicles presented by
transient (tourists) owners, and vehicles in a dealer’s inventory.

Nissan Bulletins are intended for use by qualified technicians, not 'do-it-yourselfers'. Qualified technicians are
properly trained individuals who have the equipment, tools, safety instruction, and know-how to do a job
properly and safely. NOTE: If you believe that a described condition may apply to a particular vehicle, DO
NOT assume that it does. See your Nissan dealer to determine if this applies to your vehicle.
1/57

REPAIR OVERVIEW

Replace the front passenger seat belt retractor
assembly.

Replace the front passenger airbag module.

Check and correct any DTCs set during the
instrument panel removal.

Reprogram the Airbag Diagnosis Sensor Unit.

2/57

NTB22-063B

SERVICE PROCEDURE
Front Passenger Seat Belt Retractor Assembly Replacement
1.

Open the front and rear passenger (RH) side doors, and then slide the front
passenger seat to the forward-most position, as shown in Figure 1.

Figure 1

2.

Open the hood and disconnect the negative battery terminal.


Verify the ignition is OFF before disconnecting the terminal.



Install protective tape over the negative battery terminal.



Wait a minimum of 3 minutes before proceeding, so that the air bag diagnosis unit
may fully discharge any remaining electricity.
To prevent damage to the ACC power supply, do not operate the vehicle, such as
locking/unlocking or opening/closing the doors within the 3 minute waiting period.
Protective
tape

Figure 2

3/57

NTB22-063B

To prevent the risk of personal injury or damage to the vehicle, verify the ignition switch is
OFF and a minimum of 3 minutes has elapsed since the negative battery terminal was
disconnected, before proceeding to step 3.

To prevent damage to the interior trim pieces, always use a trim removal tool made from
plastic.

3.

Remove the passenger side front kicking plate.


Disengage the thirteen (13) front kicking plate fixing pawls, as indicated by the
arrows shown in Figure 3.

: Pawl
Figure 3

4.

Remove the passenger side rear kicking plate.


Disengage the six (6) rear kicking plate fixing pawls and two (2) clips, as indicated
by the arrows shown in Figure 4.

: Pawl
: Clip
Figure 4

4/57

NTB22-063B

5.

Disengage the two (2) seat belt cover fixing pawls, and then remove the seat belt
cover.

: Pawl
Figure 5

6.

Figure 6

Remove the front and rear body side welt.

Front body
side welt

Rear body
side welt

Figure 7

7.

Disengage the two (2) center pillar lower garnish upper fixing pawls.

: Pawl

Figure 8

Figure 9
5/57

NTB22-063B

8.

Disengage the three (3) center pillar lower garnish fixing clips, and then remove the
center pillar lower garnish.
: Clip

Figure 11

Figure 10

9.

Disconnect the lap belt pre-tensioner and seat belt retractor wire harness connectors
(Figure 12).
HINT: For removing the wire harness connectors:
a. Insert a thin flat blade screwdriver, wrapped in tape, into the notch.
b. Lift the lock.
c. Remove the wire harness connector.

Seat belt retractor wire
harness connector

Lap pre-tensioner
wire harness
connector
Figure 12

Figure 13

6/57

NTB22-063B

10.

Remove the lap belt pre-tensioner mounting bolt, and then remove the lap pretensioner assembly.
HINT: Fold the carpet back to access the lap pre-tensioner mounting bolt.
Lap pre-tensioner
assembly

Lap pre-tensioner
mounting bolt
Figure 14

11.

Remove the seat belt retractor mounting bolt.
NOTE: Do not remove the seat belt retractor assembly. It will be removed at step 14
on page 9.

Seat belt retractor
anchor bolt
Figure 15

7/57

NTB22-063B

12.

Remove the shoulder belt adjuster cover.
a. Pull out on the shoulder belt adjuster cover’s lower side, and then disengage the
adjuster cover lower side fixing pawls.

Shoulder belt
adjuster cover

Shoulder belt
adjuster cover
Figure 16

: Pawl
Figure 17

b. Apply protective tape on the B-pillar trim next to the shoulder belt adjuster cover,
as shown in Figure 18.
Protective
tape

Figure 18
c. Using a remover tool, disengage the one (1) shoulder belt adjuster cover fixing
pawl, as indicated by the arrow shown in Figure 19, and then remove the adjuster
cover.
: Pawl

Remover
tool

Figure 19
8/57

NTB22-063B

13.

Remove the shoulder belt anchor mounting bolt, and then remove the shoulder belt
anchor.
Shoulder belt anchor
mounting bolt

Figure 20

14.

Remove the seat belt retractor assembly from the vehicle.
Seat belt
retractor
assembly

Figure 21

15.

Install the new seat belt retractor assembly from PARTS INFORMATION in the
reverse order of removal.


Shoulder belt anchor mounting bolt torque: 49 N•m (5.0 kg-m, 36 ft-lb)



Seat belt retractor mounting bolt torque: 49 N•m (5.0 kg-m, 36 ft-lb)



Lap belt pre-tensioner mounting bolt torque: 49 N•m (5.0 kg-m, 36 ft-lb)

16.

Verify that all seat belt retractor wire harness connector locks are fully seated.

17.

Verify seat belt retractor operation.

9/57

NTB22-063B

18.

Remove the protective tape from the negative battery terminal, and then install the
negative cable to the battery terminal.


Negative battery cable terminal nut torque: 5.4 N•m (0.6 kg-m, 48 in-lb)

Front Passenger Airbag Module Replacement
19.

Open both front doors, and then slide both front seats to the rear most position, as
shown in Figure 22 and Figure 23.

Figure 22

20.

Figure 23

Open the hood and disconnect the negative battery terminal.


Verify the ignition is OFF before disconnecting the terminal.



Install protective tape over the negative battery terminal.



Wait a minimum of 3 minutes before proceeding so that the air bag diagnosis unit
may fully discharge any remaining electricity.
To prevent damage to the ACC power supply, do not operate the vehicle, such as
locking/unlocking or opening/closing the doors within the 3 minute waiting period.
Protective
tape

Figure 24
10/57

NTB22-063B

To prevent the risk of personal injury or damage to the vehicle, verify the ignition switch is
OFF and a minimum of 3 minutes has elapsed since the negative battery terminal was
disconnected, before proceeding to step 21.

To prevent damage to the interior trim pieces, always use a trim removal tool made from
plastic.
21.

Disengage the one (1) center console fixing clip and the seven (7) metal clips, as
indicated by the arrows shown in Figure 26 and Figure 28, and then remove the driver
(LH) side and the passenger (RH) side instrument side panel.
Instrument side panel (LH)

: Metal clip

Figure 25

Figure 26
: Metal clip

Instrument side panel (RH)

: Clip

Figure 28

Figure 27
22.

: Clip

Remove the cup holder mat, and then remove the cup holder mounting screw.
Cup holder mounting screw

Figure 29
11/57

NTB22-063B

23.

Apply protective tape (A) in the location shown in Figure 30, to protect it from damage.

Figure 30

24.

Pull up on the center console finisher assembly, as indicated by the arrow shown in
Figure 32, to disengage the two (2) metal clips.
Center console
finisher
assembly

: Metal clip
Figure 31
25.

Figure 32

Using a remover tool, disengage the six (6) center console finisher assembly fixing
pawls, as indicated by the arrows shown in Figure 33, and then pull up on the center
console finisher assembly.

: Pawl
Figure 33

Figure 34
12/57

NTB22-063B

26.

Disconnect the wire harness connectors, and then remove the center console finisher
assembly.
Wire harness connector

Wire harness connectors
Figure 36

Figure 35

The electric shift selector will be removed in steps 27 and 28. The electric shift selector
contains a strong magnet. To avoid the risk of death or severe personal injury:

27.



People with an electro-medical apparatus should keep the electric shift selector
away from their body. Otherwise, it may cause the electro-medial apparatus to
malfunction.



Keep the electric shift selector away from magnetic objects such as magnetic
cards and metal items.



Never subject the electric shift selector to impact by dropping or hitting it, water
splash or high humidity.

Remove the four (4) bolts securing the electric shift selector, and then remove the
electric shift selector.

Bolts (4)
Figure 37

13/57

NTB22-063B

28.

Disconnect the wire harness connector from the electric shift selector.

Wire harness connector
Figure 38

29.

Open the center console lid and disengage the six (6) center console rear finisher
fixing metal clips, as indicated by the arrows shown in Figure 40, and then pull out the
center console rear finisher.
: Metal clip

Center console rear finisher
Figure 39
30.

Figure 40

Disconnect the wire harness connectors, and then remove the center console rear
finisher.
Wire harness connectors