NHTSA ID Number: 10211960
Manufacturer Communication Number: TSB_ENG328
TSB/Document Date: 2022-06-03
Summary
TECHNICAL SERVICE BULLETIN: SERVICE ACTION: ECM LOGIC IMPROVEMENT FOR DTC P0456/P013E (SA498) - This bulletin provides the procedure to update the software logic of the Engine Control Module (ECM) system on some 2023MY Sportage (NQ5/NQ5a) vehicles equipped with Theta 2.5L GDI engine and 8AT produced in the date ranges shown below, which may exhibit a MIL ON with DTC P0456 or P013E. Follow the procedure outlined in this publication to apply the improved logic to the 'Engine' system using the KDS ECU Upgrade function as described in this bulletin.
GROUP
MODEL
ENG
2023MY
Sportage (NQ5/NQ5a)
NUMBER
DATE
238
May 2022
TECHNICAL SERVICE BULLETIN
SUBJECT:
SERVICE ACTION: ECM LOGIC IMPROVEMENT
FOR DTC P0456/P013E (SA498)
This bulletin provides the procedure to update the software logic of the Engine Control Module (ECM) system
on some 2023MY Sportage (NQ5/NQ5a) vehicles equipped with Theta 2.5L GDI engine and 8AT produced in
the date ranges shown below, which may exhibit a MIL ON with DTC P0456 or P013E. Follow the procedure
outlined in this publication to apply the improved logic to the ‘Engine’ system using the KDS ECU Upgrade
function as described in this bulletin. For confirmation that the latest reflash has been applied to a vehicle you
are working on, verify the ROM ID using the table on page 3 of this bulletin. Before conducting the procedure,
verify that the vehicle is included in the list of affected VINs.
DTC Description:
•
P0456: Evaporative Emission System / Leak Detected (very small leak)
•
P013E: O2 Sensor Delayed Response / Rich to Lean Bank 1 Sensor 2
Model
Production Date Range
Sportage (NQ5)
December 15, 2021 to April 15, 2022
Sportage (NQ5a)
January 25, 2022 to April 25, 2022
NOTICE
A Service Action is a repair program without customer notification that is performed during the
warranty period. Any dealer requesting to perform this repair outside the warranty period will
require DPSM approval.
Repair status for a VIN is provided on WebDCS (Service → Warranty Coverage → Warranty Coverage
Inquiry → Campaign Information). Not completed Recall / Service Action reports are available on
WebDCS (Consumer Affairs → Not Completed Recall → Recall VIN → Select Report), which includes
a list of affected vehicles.
This issue number is SA498.
A printed copy is for reference only; publication information can be updated at any time.
Always refer to KGIS for the latest information. After logging in kdealer.com, the newest technical
publications are listed in ‘Service Releases’ and has the latest service information that has been released.
Page 2 of 8
SUBJECT:
SERVICE ACTION: ECM LOGIC IMPROVEMENT FOR DTC P0456/P013E (SA498)
ECU Upgrade Procedure:
To correct this condition, the ECU should be reprogrammed using the KDS
download, as described in this bulletin.
Upgrade Event Name
617. NQ5/NQ5a THETA 2.5GDI ENGINE MIL ON DTC (P0456, P013E) JUDGMENT LOGIC IMPROVEMENT
NOTICE
•
Confirm a fully charged battery (12.3 volts or higher is necessary) is used or utilize a fully
charged jump starter
box connected to the battery.
•
Ensure the KDS is sufficiently charged at 60% or higher prior to reflash.
•
All ECU upgrades must be performed with the ignition set to the ‘ON’ position unless otherwise
stated.
•
Damaged VCI II units should not be used and promptly replaced.
•
Be careful not to disconnect the VCI-II connected to the vehicle during the ECU upgrade
procedure.
•
DO NOT start the engine during ECU upgrade.
•
DO NOT turn the ignition key ‘OFF’ or interrupt the power supply during ECU upgrade.
•
When the ECU upgrade is completed, turn the ignition ‘OFF’ and wait 10 seconds before
starting the engine.
•
ONLY use approved ECU upgrade software designated for the correct application.
IMPORTANT
It is recommended to ALWAYS check the Electronic Parts Catalog (EPC) to locate the ECU Part
Number respective to Auto/Manual Mode ROM IDs. DO NOT reference the parts label affixed to
the ECU.
Printed TSB copy is for reference only; information may be updated at any time. Always refer to KGIS for the latest information.
TSB: SA498 Sportage (NQ5/NQ5a) May 2022
Page 3 of 8
SERVICE ACTION: ECM LOGIC IMPROVEMENT FOR DTC P0456/P013E (SA498)
SUBJECT:
Before attempting an ECU upgrade on any Kia model, make sure to first determine whether the
applicable model is equipped with an immobilizer
security system. Failure to follow proper
procedures may cause the PCM to become inoperative after the upgrade and any claims associated
with this repair may be subject to chargeback.
ROM ID INFORMATION TABLE:
Upgrade Event #617
Model
EM
TM
2WD/
4WD
IMMO
ROM ID
ECU
P/No.
Previous
39100
NQDWD5GMAXXXXL7A
2S210
NQEWD5GMAXXXXL7A
39100
NQDWD5GKAXXXXL7A
NQ5
2S215
NQEWD5GKAXXXXL7A
(2.5 GDI)
39100
NQDWD5GMJXXXXL7A
2S232
NQEWD5GMJXXXXL7A
39100
NQDWD5GKJXXXXL7A
2S233
NQEWD5GKJXXXXL7A
2WD/
4WD
New
NQEWD5GMAXXXXL7B
NQEWD5GKAXXXXL7B
NQEWD5GMJXXXXL7B
4WD
ULEV
70
8AT
NQEWD5GKJXXXXL7B
Yes
39100
2WD/
4WD
2S226
39100
NQ5a
2S231
(2.5 GDI)
39100
2S234
NQEWN5GMAXXXXL7A
NQEWN5GMAXXXXL7B
NQEWN5GKAXXXXL7A
NQEWN5GKAXXXXL7B
NQEWN5GMJXXXXL7A
NQEWN5GMJXXXXL7B
NQEWN5GKJXXXXL7A
NQEWN5GKJXXXXL7B
4WD
39100
2S235
To verify the vehicle is affected, be sure to check the Calibration Identification of the vehicle's ECM ROM ID
and reference the Information Table as necessary.
Printed TSB copy is for reference only; information may be updated at any time. Always refer to KGIS for the latest information.
TSB: SA498 Sportage (NQ5/NQ5a) May 2022
Page 4 of 8
SUBJECT:
SERVICE ACTION: ECM LOGIC IMPROVEMENT FOR DTC P0456/P013E (SA498)
NOTICE
Prior to performing the ECU upgrade, be sure to check that the KDS is fully charged.
Connect the VCI-II to the OBD-II connector,
located
under
the
driver’s
side
of
the
instrument panel.
NOTICE
The ECU upgrade function on KDS
operates wirelessly. It is not necessary
to perform the upgrade via USB cable.
With the ignition ON, turn ON the KDS tablet.
Select ‘KDS’ from the home screen.
Confirm communication with VCI (A) and then
configure the vehicle (B) using the ‘AUTO VIN’
(C) feature.
B
A
C
Select ‘ECU Upgrade’.
Printed TSB copy is for reference only; information may be updated at any time. Always refer to KGIS for the latest information.
TSB: SA498 Sportage (NQ5/NQ5a) May 2022
Page 5 of 8
SUBJECT:
SERVICE ACTION: ECM LOGIC IMPROVEMENT FOR DTC P0456/P013E (SA498)
The KDS will check the server for recently
uploaded
Events
and
then
automatically
download Upgrade Event #617.
NOTICE
The vehicle must be identified in
Vehicle Selection to download an
Event for that vehicle.
KDS
screenshot
shown
above
is
for
demonstration purposes only. Events shown in
screenshot are not applicable to this bulletin.
Select Auto Mode.
CAUTION
Do NOT attempt to perform a Manual
Mode upgrade UNLESS Auto Mode
fails. Always follow the instructions
given on the KDS in either Auto or
Manual mode.
Select the ENGINE system under the System
selection menu.
Touch ID Check (D) and confirm that the latest
D
update is available.
Select Upgrade Event #617 and select Upgrade
to continue.
The ECU upgrade will begin and the progress
of the upgrade will appear on the bar graph.
E
Upgrade part (1/2) (E) will download the
upgrade event to the VCI-II. Upgrade part (2/2)
(F) will upgrade the ECU.
CAUTION
F
Do not touch the system buttons (like
‘Back’,
‘Home’,
‘etc.’)
while
performing ECU Upgrade.
Printed TSB copy is for reference only; information may be updated at any time. Always refer to KGIS for the latest information.
TSB: SA498 Sportage (NQ5/NQ5a) May 2022
Page 6 of 8
SUBJECT:
SERVICE ACTION: ECM LOGIC IMPROVEMENT FOR DTC P0456/P013E (SA498)
If a “Communication Fail” screen appears, verify
that the VCI-II and KDS are communicating
properly. Select ‘OK’ and restart the procedure
from step 4.
NOTICE
If an error notice continues to appear
or
if
the
upgrade
cannot
be
performed, DO NOT disconnect the
KDS/VCI-II. Contact GIT America Help
Desk at (888) 542-4371 or Techline.
When instructed on the KDS, turn the ignition
OFF for ten (10) seconds then back on. Select
‘OK’ to continue.
Once the upgrade is complete, select ‘OK’ to
finalize the procedure.
When prompted, select ‘YES’ to check for
Diagnostic Trouble Codes (DTC) and erase any
DTCs stored such as EPS, ESC, and TPMS that
may have been set during the upgrade.
Start the engine to confirm normal operation of
the vehicle.
Printed TSB copy is for reference only; information may be updated at any time. Always refer to KGIS for the latest information.
TSB: SA498 Sportage (NQ5/NQ5a) May 2022
Page 7 of 8
SUBJECT:
SERVICE ACTION: ECM LOGIC IMPROVEMENT FOR DTC P0456/P013E (SA498)
Manual Upgrade Procedure:
NOTICE
The manual upgrade should ONLY be performed if the automatic upgrade fails.
If the automatic upgrade fails, turn the ignition ‘OFF’ for about 10 seconds then place it back in
the ‘ON’ position to reset the control unit BEFORE performing manual upgrade.
See table below for ‘Manual Mode’ passwords.
Manual Mode ECU Upgrade Passwords
Menu
Password
NQ5 2.5GDI ULEV70 2/4WD: 39100-2S210
2210
NQ5 2.5GDI ULEV70 2/4WD: 39100-2S215
2215
NQ5 2.5GDI ULEV70 4WD: 39100-2S232
2232
NQ5 2.5GDI ULEV70 4WD: 39100-2S233
2233
NQ5a 2.5GDI ULEV70 2/4WD: 39100-2S226
2226
NQ5a 2.5GDI ULEV70 2/4WD: 39100-2S231
2231
NQ5a 2.5GDI ULEV70 4WD: 39100-2S234
2234
NQ5a 2.5GDI ULEV70 4WD: 39100-2S235
2235
Within the ECU Upgrade screen displayed, select Manual Mode.
Select the ENGINE system under the System selection menu. Select Upgrade Event #617 and select
Upgrade to continue.
Select the appropriate control unit part number with reference to the ROM ID Information Table on
page 3, and select OK.
Enter the appropriate password from the Manual Mode password table above and select OK.
The upgrade will begin and the progress of the upgrade will appear on the bar graph.
When instructed on the KDS, turn the ignition OFF for ten (10) seconds then back on. Select OK.
Once the upgrade is complete, select OK to finalize the procedure.
When prompted, select YES to check for Diagnostic Trouble Codes (DTC) and erase any DTCs stored
such as EPS, ESC, and TPMS that may have been set during the upgrade.
Start the engine to confirm proper operation of the vehicle.
Printed TSB copy is for reference only; information may be updated at any time. Always refer to KGIS for the latest information.
TSB: SA498 Sportage (NQ5/NQ5a) May 2022
Page 8 of 8
SERVICE ACTION: ECM LOGIC IMPROVEMENT FOR DTC P0456/P013E (SA498)
SUBJECT:
AFFECTED VEHICLE RANGE:
Model
Production Date Range
Sportage (NQ5)
December 15, 2021 to April 15, 2022
Sportage (NQ5a)
January 25, 2022 to April 25, 2022
REQUIRED TOOL:
Tool Name
Figure
Comments
KDS
Kia Diagnostic System
WARRANTY INFORMATION:
N Code: N99 C Code: C99
Model
Claim
Causal
Type
P/N
Qty.
NQ5
V
NQ5a
39100
2S210
Repair
Labor Op
Op
Replacement
Description
Code
Time
P/N
(SA498)
0
220055R0
0.3
ECM Logic
Improvement
Qty.
M/H
N/A
0
220A04R0
NOTICE
VIN inquiry data for this repair is provided for tracking purposes only. Kia retailers should reference
SA498 when accessing the WebDCS system.
Printed TSB copy is for reference only; information may be updated at any time. Always refer to KGIS for the latest information.
TSB: SA498 Sportage (NQ5/NQ5a) May 2022
If the PDF is very large, it may not load in the preview below.
Some older TSBs had multiple PDFs — visit the NHTSA Website to view all PDFs.
If the TSB PDF does not show, download or view it on the NHTSA Website.
Click on the (+) Plus Sign
Then Click on Associated Document(s)
Search NHTSA Database for Recalls
Search NHTSA Database for Vehicle Investigations
View Latest Vehicle Investigations
Search NHTSA Database for Vehicle Complaints
View Latest Vehicle Complaints
TSB/Document ID: TSB_ENG328
Replacement Service Bulletin Number:
MFR Communication Date: 2022-05-18
MFR Internal Campaign ID/Software Version:
Communication Type: Service Bulletin/Repair Instructions
NHTSA Components: ENGINE AND ENGINE COOLING
MFR Component System:
MFR Component Subsystem:
Previous TSB | Next TSB |
- [Notice] When you receive a used device, it may be a customer return resold by Amazon without inspection. You can exchange it for a new one through Amazon. As this situation is unavoidable, we sincerely apologize. For any issues, contacting us via Amazon's "Messages" is the best way. THINKSCAN 689BT Bidirectional Scan Tool Can Be Used Immediately After It is Turned On, Without Complicated Registration Process, Which is More Convenient & Quick.
- Full Bi-Directional Control & 3000+ Active Tests: Take control and test components like actuators, fuel injectors, relays, and cooling fans in real time. You’ll quickly see if the problem is in the part itself or the control module — saving you hours of guesswork and frustrating trial-and-error.
- Advanced ECU Coding Capabilities: Handle module matching and hidden feature activation with confidence. When you replace an ECU or want to customize settings, this obd2 scanner diagnostic bi directional tool gives you the professional-level capabilities you need without the dealership price tag.
- 34+ Useful Reset and Maintenance Functions: Complete everyday service tasks smoothly with a wide range of helpful reset and maintenance functions. Whether you’re keeping up with regular upkeep or tackling a specific job, this scanner makes maintenance simpler and less stressful for both DIYers and pros.
- Comprehensive Full System Diagnostics: Diagnose every major system — Engine, Transmission, ABS, SRS, TPMS, and more — all in one place. Finally stop wondering if you’re missing something important; get the full picture and clear codes with ease.
- Top Reasons to Choose the D7S OBD2 Scanner: XTOOL D7S car scan tool, an upgrade of XTOOL D7, offers comprehensive features for automotive technicians, workshops, and DIY enthusiasts 1. Upgraded Hardware: 2+64GB memory, rear camera, intuitive interface, foldable bracket 2. Complete Diagnostics: FCA
Autoauth, OE-level all system scan, 39+ maintenance services, 4K+ bidirectional, CANFD/DoIP protocol 3. Advanced Capabilities: ECU c0ding, PMI functions 4. Wide Compatibility: Support 10,000+ models, covering 99% vehicle brands 5. Multi-language: Available in 22+ languages, No IP Restrictions 6. 3-Year Updates: Save 300 bucks on software updates for the latest features and optimizations - 2026 Upgraded D7S Car Scanner Features: The newly 2026 D7S V2.0 scanner for car brings exciting features for advanced vehicle diagnostics and enhanced user experience 1. FCA AutoAuth: Now supports FCA SGW module for Chrysler, for Jeep, for Dodge (2018+), for Fiat (2017+), enabling faster vehicle communication without gateway restrictions 2. PMI (Offline ECU Pr0gramming): Allows for Ford, for Lincoln, and for Mazda ECU pr0gramming for new modules 3. Optimized Diagnostic Report 2.0: Personalized reports with logos and customer info for auto shops. Note: Compatibility varies by cars, please check before order
- 39+ Services/Resets/Adaptations/Relearns/Calibrations: XTOOL D7S full system car scanner diagnostic tool tackles 99% of common car issues through its 36+ special functions, including Oil Reset, EPB, SAS, BMS, Throttle Reset, Injector C0ding, ABS Bleed, TPMS Reset, Power Balance, etc and also covers specific-vehicle functions like Crank Sensor Relearn, ABS Initialization, Cylinder Power Balance, Fuel Trim Reset, Idle Relearn etc. This car diagnostic scanner enhances efficiency, making repairs and maintenance hassle-free. Tip: DO NOT for All vehicles, please check compatibility first
- Cost-effective ECU C0ding Scan Tool for Specific Brands: Enhance your vehicle's performance with XTOOL D7S! This obd2 scanner all systems bidirectional offers advanced capabilities at an affordable price, supports online for BMW, for Benz and offline for BENZ, for MIT, along with PMI functions for Ford, for Mazda, and for Lincoln. Ideal for technicians and DIY enthusiasts, this automotive scanner diagnostic tool optimizes vehicle performance and enhances the driving experience. Note: Not for all cars and modules, please send car VIN to check the compatibility before purchase
- OE All System Diagnostic & 8 Pids Graphing: XTOOL D7S is a comprehensive all system bi directional obd2 scanner that delivers dealer-level diagnostics, completely controlling over your vehicle’s performance and health. This automotive scan tool can read and clear DTCs, view live data and ECU information, retrieve freeze frames, and perform active tests and full obd2 functions. This bi-directional scan tool can can identify your vehicle's make, model, and year information with just one click and show up to 8 PIDs live data with options for CSV viewing, playback, and recording for in-depth analysis. It is easy-to-use for both professionals and beginners, helping pinpoint issues efficiently
- 【✅Compared to BOSSCOMM IF742, IF745 Offers Full-System Diagnostics】The BOSSCOMM IF745 car diagnostic scanner is an upgraded model of IF742. In addition to supporting all OBD2 Code Reader functions and 6 reset options (ABS/EPB/SAS/BMS/Oil/Throttle), it expands diagnostics from 4 systems (Check Engine/ABS/SRS/Transmission) to vehicle All systems, including Steering, Suspension, and Body Electronics. This provides deeper, more comprehensive diagnostic capabilities.
- 【✨10 OBD2 Functions】The BOSSCOMM IF745 scan tool’s DTC Lookup instantly translates fault codes into user-friendly explanations, its I/M Readiness feature streamlines emissions testing with a single tap, and Freeze Frame lets you pinpoint the exact moment of a fault for in-depth root-cause diagnosis. Combined with a live data dashboard and advanced diagnostics (O2S, OBMon, EVAP), it delivers comprehensive insights for confident troubleshooting.
- 【✨Deep Diagnostics for All Vehicle System Modules】Beyond code reading/clearing and ECU information retrieval, our all-in-one data stream feature lets you inspect all current fault codes and their locations across the vehicle’s systems. This vehicle code reader helps you turn off dashboard warning lights and perform a comprehensive self-check of your car at home—no more back-and-forth trips to the repair shop or hefty inspection fees.
- 【✨6 Essential Resets: ABS Bleeding, Oil, EPB, SAS, Throttle, BMS】The BOSSCOMM IF745 obd2 scanner diagnostic tool swiftly purges air from brake lines to restore braking sensitivity, fine-tunes maintenance cycles to eliminate false alerts, resolves parking brake issues with one-click control, recalibrates steering sensors for stability, optimizes engine idling/acceleration for smoother performance, and deeply resets battery systems to extend lifespan and range via precise parameter adjustments.❗NOTE: Does NOT support bidirectional control, coding, or programming.
- 【✨10,000+ Car Models, AutoVIN, 13 Languages】The BOSSCOMM IF745 vehicle scanner diagnostic tool covers 73+ global car brands and offers support in 13 languages, making it perfect for DIYers, auto mechanics, or as a thoughtful gift. With a single-click AutoVIN feature, it instantly retrieves vehicle serial numbers, streamlining diagnostics for users globally. This adaptable tool balances user-friendliness with precision, catering to both personal and professional requirements.✅Unsure about compatibility? Compatibility will vary on vehicles' model and year, pls reach us via 📧 [email protected] 📧 before purchase.
This product presentation was made with AAWP plugin.