Turn off the ignition and all electrical
equipment.



If equipped remove the ignition key.



Lift the locking tabs on cover and
remove cover in direction of .



Disconnect the connectors on the
OCU .



Lift locking tabs using a small screwdriver
or pick.



Remove OCU in direction of .



Install the new OCU in the reverse order
of removal.



Reconnect connector .



DO NOT RECONNECT THE ANTENNAS
AT THIS TIME!!

The repair information in this document is intended for use only by skilled technicians who have the proper tools, equipment and training to correctly and safely maintain your vehicle. These
procedures are not intended to be attempted by “do-it-yourselfers,” and you should not assume this document applies to your vehicle, or that your vehicle has the condition described. To
determine whether this information applies, contact an authorized Volkswagen dealer. 2022 Volkswagen Group of America, Inc. All Rights Reserved.
May 2022
91BM Page 8 of 15

Adapting new OCU:


Apply the parking brake.



Switch off all consumers (headlights, heated
seats, climate control, etc.).



Connect
the
VAS6150X/VAS6160X
Diagnostic Tester to the vehicle.



Start the ODIS program.



Attach the GRX3000VAS Tester/Charger (or
equivalent) IN POWER SUPPLY MODE to the
vehicle battery.



Confirm that scan tool is communicating with
the diagnostic head by USB .



If the Bluetooth symbol is shown
then disconnect the diagnostic head from the
vehicle and reconnect the USB cable to the
diagnostic head and then reattach to the
vehicle.



Upon ODIS startup, verify the “Diagnosis”
operating mode is selected .



When a message appears regarding “Vehicle
position detection” and “Emergency call
module and communication” modules not
being coded, select “Close” .



Once the GFF scan is complete, perform the
“Adapting Software” test plan:



Select “Special functions”



Select “Adapting software”



Select “Perform test”



Follow the on-screen prompts

The repair information in this document is intended for use only by skilled technicians who have the proper tools, equipment and training to correctly and safely maintain your vehicle. These
procedures are not intended to be attempted by “do-it-yourselfers,” and you should not assume this document applies to your vehicle, or that your vehicle has the condition described. To
determine whether this information applies, contact an authorized Volkswagen dealer. 2022 Volkswagen Group of America, Inc. All Rights Reserved.
May 2022
91BM Page 9 of 15



Select the option, “Perform conversion/retrofit
solution.”



Enter the action code as listed below.

SVM code

37CEE


Select “Accept” and follow the on
screen prompts.



After the conversion/retrofit operation is
complete, identify the new OCU:



Select the “Control Module” tab.



Scroll down and right click on address 0075.



Select “Identify Control Module” .

The repair information in this document is intended for use only by skilled technicians who have the proper tools, equipment and training to correctly and safely maintain your vehicle. These
procedures are not intended to be attempted by “do-it-yourselfers,” and you should not assume this document applies to your vehicle, or that your vehicle has the condition described. To
determine whether this information applies, contact an authorized Volkswagen dealer. 2022 Volkswagen Group of America, Inc. All Rights Reserved.
May 2022
91BM Page 10 of 15



After identifying the new OCU, select the
Special Functions tab.



Select Ctrl. module software configuration.



When prompted, select
Diagnostic Address.



Enter 0075 for the Diagnostic Address.



Follow the on-screen prompts.



After the Software Configuration operation is
complete, adapt the OCU to the Anti-Theft
Immobilizer:



Right click on address 0025 and select Guided
Functions



Perform function “25 – Adapt OCU” .



Follow the on-screen prompts.

the

option

for

TIP
Additional ignition keys are NOT required for this
test plan.


After adapting the Anti-Theft Immobilizer,
perform Test Plan “Teach VKMS”:



Select the “Test Plan” tab.



Select “Select Self Test”



Select: Body > Electrical Systems > 01 –
Systems Capable of Self Diagnosis > 25 –
Immobilizer
>
25 – VKMS Functions



Select VKMS Adaptation.



Then Attach to the test plan.



Follow the on-screen prompts



During this test plan, you will be prompted to
hold the ignition key to the reader coil. Ensure
the key is held steady against the reader coil,
otherwise errors could occur.

The repair information in this document is intended for use only by skilled technicians who have the proper tools, equipment and training to correctly and safely maintain your vehicle. These
procedures are not intended to be attempted by “do-it-yourselfers,” and you should not assume this document applies to your vehicle, or that your vehicle has the condition described. To
determine whether this information applies, contact an authorized Volkswagen dealer. 2022 Volkswagen Group of America, Inc. All Rights Reserved.
May 2022
91BM Page 11 of 15



If there is an error during the “Teach VKMS”
test plan (see example shown), repeat the test
plan and ensure the key is held steady against
the reader coil for the duration of the test plan.

Reconnect antennas to the OCU:


Reconnect antennas to the OCU .

Exit GFF and clear repair related faults:


Exit GFF and send diagnostic protocol online
when prompted.



Disconnect the diagnostic tester from the
vehicle.

The repair information in this document is intended for use only by skilled technicians who have the proper tools, equipment and training to correctly and safely maintain your vehicle. These
procedures are not intended to be attempted by “do-it-yourselfers,” and you should not assume this document applies to your vehicle, or that your vehicle has the condition described. To
determine whether this information applies, contact an authorized Volkswagen dealer. 2022 Volkswagen Group of America, Inc. All Rights Reserved.
May 2022
91BM Page 12 of 15

Confirm operation of Car-Net button array:


Take the vehicle outside with clear line of sight
to the sky.



Initiate a bus sleep by locking the car with the
remote.



Recheck operation after 10 minutes.



The 3-Button Module LED should be green
and user should be able to connect to Car-Net
services.

TIP
It make take a few minutes for the green light to
illuminate after the bus sleep period.


Verify the button array is working by pressing
the “i” call button .



If the green light is not illuminated:



There may be an issue outside of the scope of
this action.
o

Contact
Volkswagen
Technical
Assistance if further assistance is needed.

o

Any additional diagnosis and repairs if the
green light does not illuminate will not be
covered under this action.

TIP
If any static communication faults were stored
during this procedure, these faults should be able to
be erased after the bus sleep period.

Proceed to Section C

The repair information in this document is intended for use only by skilled technicians who have the proper tools, equipment and training to correctly and safely maintain your vehicle. These
procedures are not intended to be attempted by “do-it-yourselfers,” and you should not assume this document applies to your vehicle, or that your vehicle has the condition described. To
determine whether this information applies, contact an authorized Volkswagen dealer. 2022 Volkswagen Group of America, Inc. All Rights Reserved.
May 2022
91BM Page 13 of 15

Section C – Car-Net Registration


Advise the customer that they can now register
for their Car-Net services by pressing the “i”
button in the Car-Net button array.



Print out the Car-Net Quick Reference Guide
attached to end of this document and provide
it to the customer.



Proceed to Section D.

The repair information in this document is intended for use only by skilled technicians who have the proper tools, equipment and training to correctly and safely maintain your vehicle. These
procedures are not intended to be attempted by “do-it-yourselfers,” and you should not assume this document applies to your vehicle, or that your vehicle has the condition described. To
determine whether this information applies, contact an authorized Volkswagen dealer. 2022 Volkswagen Group of America, Inc. All Rights Reserved.
May 2022
91BM Page 14 of 15

Section D – Campaign Completion Label
Install Campaign Completion Label


Fill out and affix Campaign Completion
Label, part number CAMP 010 000, next to
the vehicle emission control information
label.

TIP
Ensure Campaign Completion Label does not cover
any existing label(s).

Repair Overview

The repair information in this document is intended for use only by skilled technicians who have the proper tools, equipment and training to correctly and safely maintain your vehicle. These
procedures are not intended to be attempted by “do-it-yourselfers,” and you should not assume this document applies to your vehicle, or that your vehicle has the condition described. To
determine whether this information applies, contact an authorized Volkswagen dealer. 2022 Volkswagen Group of America, Inc. All Rights Reserved.
May 2022
91BM Page 15 of 15