Installation and Conversion Instructions

Macan (95B)
23/14

ENU

6807

6

Door Entry Guard, Illuminated

Revision:

This bulletin replaces bulletin Group 6, #23/14, dated January 22, 2016.
Reason: Page 1 “Note” technical modification date was changed from November 2015 to Calendar week
22/2016.

Model Year:

As of 2014

Concern:

Retrofitting

Note:

The illuminated door entry guards made of carbon-fiber composite or aluminum are installed in the front
door sill areas.
Technical modification to Macan and Macan Diesel from week 22/2016:
No slots in front inner door sill trim (lower A-pillar trim panel).  Door entry guard cannot be secured.
For this reason, check the customer vehicle and order lower A-pillar trim panels if necessary (see Part Info
section).

Parts Info:

95B.044.80X.XX

 Carbon-fiber composite/aluminum door entry guard with
“model designation”, set

For Macan and Macan Diesel vehicles manufactured from week 22/2016 (new model year), also order
the following:

2016© Porsche Cars North America, Inc.

Tequipment

Mar 1, 2016
Page 1 of 16

6

Macan (95B)
6807

ENU

95B.863.483.B FFF1

1x

A-pillar trim panels, lower left

95B.863.484.B FFF1

1x

A-pillar trim panels, lower right

1

Parts List:

Installation and Conversion Instructions

23/14

For color code, see Porsche Electronic Parts Catalog, Macan, illustration 807-22.

Macan Turbo as an example.

Figure 2
———

1x

———

1x

— — —2

1x

Carbon-fiber composite door entry guard, left, illuminated 
Figure 2 -1Carbon-fiber composite door entry guard, right, illuminated 
Figure 2 -2Carbon-fiber composite lock carrier trim, rear right (not shown)

— — —2

1x

Carbon-fiber composite lock carrier trim, rear left (not shown)

———

1x

Aluminum door entry guard, left, illuminated  Figure 2 -3-

———

1x

Aluminum door entry guard, right, illuminated  Figure 2 -4-

———

1x

Wire harness  Figure 2 -5-

———

20 x

Tie-wrap (not shown)

2

Only contained in carbon-fiber composite illuminated door entry guard set.

Materials:

———

Tools:

9818 - PIWIS Tester II

Work Procedure: 1

Mar 1, 2016
Page 2 of 16

——

Cleaning agent (commercially available)

Preparatory work.

Tequipment

2016© Porsche Cars North America, Inc.

Installation and Conversion Instructions

Macan (95B)
23/14

ENU

6807

6

1.1

Remove front inner door sill trim at the left and right.  Workshop Manual '680519
Removing and installing front inner door sill trim'

1.2

Remove upper part of B-pillar trim panel at the left and right.  Workshop Manual '706719
Removing and installing upper part of B-pillar trim panel'

1.3

Remove lower part of B-pillar trim panel at the left and right.  Workshop Manual '706719
Removing and installing lower part of B-pillar trim panel'

1.4

Remove rear seat.  Workshop Manual '724819 Removing and installing rear seat'

1.5

Remove rear right backrest.  Workshop Manual '724719 Removing and installing rear
backrest'

1.6

Remove cover for rear lock support.  Workshop Manual '703919 Removing and installing
cover for rear lock support'

1.7

Remove side trim panel for rear luggage compartment at the right.  Workshop Manual
'700319 Removing and installing side trim panel for rear luggage compartment'

1.8

Only for vehicles with rear seat airbag:

1.9

1.8.1

Disconnect the battery.  Workshop Manual '270619 Removing and installing
battery'

1.8.2

Remove rear right seat airbag.  Workshop Manual '696419 Removing and
installing rear seat airbag'

Remove rear inner door sill trim at the right 
Figure 3 -1-.  Workshop Manual '680519
Removing and installing rear inner door sill
trim'

Figure 3
1.10

Unclip rear inner door sill trim at the left 
Figure 4 -1- in the front area from the body 
Figure 4 -arrow a-.
Lift carpet in front of the rear seat  Figure 4
-2- ( Figure 4 -b-) and expose cable duct 
Figure 4 -3-.

2

Install electric wire harness.
2.1

Secure electric wire harness (end of line
without pin connector socket) to auxiliary line.
Figure 4

2016© Porsche Cars North America, Inc.

Tequipment

Mar 1, 2016
Page 3 of 16

6

Macan (95B)
6807

ENU

23/14

Installation and Conversion Instructions

Information
Removing the pin connector socket makes it easier to guide the wire harness through the
cable duct.
2.2

Press out pin contact of YE/GY line at the
shorter end of the wire harness.
2.2.1

Insert a screwdriver in between the
secondary lock  Figure 5 -1- and
pin connector socket  Figure 5
-arrow- and open the secondary
lock  Figure 5 -arrow a-.

2.2.2

Release pin contact using press-out
tool  Figure 5 -arrow b- and pull
out YE/GY line  Figure 5 -2- (
Figure 5 -arrow c-).

2.2.3

To protect the pin contact, secure
the YE/GY line that you pressed out
to the wire harness using wrapping
tape.
Figure 5

2.3

Route electric wire harness as follows:
Left A-pillar → main wire harness in
passenger compartment at the left →
cable duct in front of rear seat → main wire
harness in passenger compartment at
the right → left A-pillar → wire harness in
luggage compartment at the right → rear-end
electronics control unit

Figure 6

Mar 1, 2016
Page 4 of 16

Tequipment

2016© Porsche Cars North America, Inc.

Installation and Conversion Instructions
2.3.1

Macan (95B)
23/14

ENU

6807

6

Push pin connector socket 
Figure 7 -1- onto the upper guide 
Figure 7 -3- at the connection point
holder  Figure 7 -2- ( Figure 11
-arrow-).
Secure cable ring eyelet to ground
pin 21  Figure 7 -4-.
Tightening torque 9 Nm
(6.5 ftlb.)

Figure 7
2.3.2

Open rear left cable duct  Figure
8 -arrow-.

Figure 8
2.3.3

Route electric wire harness
 Figure 9 -1- along the main
wire harness in the passenger
compartment at the left  Figure 9
-2- through the cable duct  Figure
9 -3- in front of the rear seat to the
right-hand side of the vehicle.

Figure 9

2016© Porsche Cars North America, Inc.

Tequipment

Mar 1, 2016
Page 5 of 16

6

Macan (95B)
6807

ENU

23/14
2.3.4

Installation and Conversion Instructions
Close rear left cable duct  Figure
10 -arrow-.

Figure 10
2.3.5

Route electric wire harness (YE/GY
line) along the main wire harness in
the passenger compartment to the
right A-pillar.

Figure 11
2.3.6

Insert pin contact of the YE/GY
line  Figure 12 -1- into the pin
connector socket  Figure 12
-arrow a-.
Close secondary lock  Figure 12
-2- ( Figure 12 -arrow b-).

Figure 12

Mar 1, 2016
Page 6 of 16

Tequipment

2016© Porsche Cars North America, Inc.

Installation and Conversion Instructions
2.3.7

Macan (95B)
23/14

ENU

6807

6

Push pin connector socket 
Figure 13 -1- onto the upper guide
 Figure 13 -2- at the connection
point holder.
Secure cable ring eyelet to ground
pin 22  Figure 13 -3-.
Tightening torque 9 Nm
(6.5 ftlb.)

Figure 13
2.3.8

2.4

Route electric wire harness 
Figure 14 -1- (YE/GY line) along
the wire harness in the luggage
compartment at the right to the
rear-end electronics control unit 
Figure 14 -2-.

Connect YE/GY line to the rear-end electronics control unit.

Figure 14
2.4.1

Disconnect electric plug connection

 Figure 15 -1- from the rear-end
electronics control unit. 
Workshop Manual '578919
Removing and installing control unit
for rear-end electronics'

Figure 15

2016© Porsche Cars North America, Inc.

Tequipment

Mar 1, 2016
Page 7 of 16

6

Macan (95B)
6807

ENU

23/14
2.4.2

Installation and Conversion Instructions
Open the locking mechanism 
Figure 16 -arrow- and slide the
grey plug socket  Figure 16 -1out of the black plug carrier 
Figure 16 -2-.

Figure 16
Information
Ensure socket contact is seated securely.
2.4.3

Insert socket contact  Figure 17
-arrow- into chamber 8 of the grey
plug socket.

2.4.4

Slide grey plug socket into the plug
carrier until the locking mechanism
engages.

Figure 17
2.4.5

Connect electric plug connection

 Figure 18 -arrow- to the
rear-end electronics control unit.

 Workshop Manual '578919

Removing and installing control unit
for rear-end electronics'
2.5

Secure electric wire harness to the standard
wire harness with a tie-wrap.

Information
Some of the repair illustrations show only one side
Figure 18
of the vehicle. Naturally, some steps also have to be
performed on the opposite side of the vehicle as well. These must be carried out as a mirror image
of the steps shown.

Mar 1, 2016
Page 8 of 16

Tequipment

2016© Porsche Cars North America, Inc.

Installation and Conversion Instructions
3

Macan (95B)
23/14

ENU

6807

6

Install illuminated door entry guard in the inner door sill trim.
3.1

Remove standard door entry guard.
3.1.1

Bend up tabs  Figure 19 -1-.

Figure 19