L624A.02.16

To:
Subject:
Date:

Official After Sales Network
Engine & gearbox SW update
March 18,2016

Pages

15

Subject.
Engine & gearbox SW update

Component code:
Trouble code:
Labor code:
Labor Time:

Model.
Huracan Coupè.
Model year.
2015

CCA0216
220
CC0216100
0,7 h

Remember to fill all data in the section “Service and Recall Campaign” in the Warranty booklet of the vehicle as
shown below.

Special or Limited Versions.
All vehicle versions.
Markets.
All.
VIN identification.
From FLA00163 to VIN FLA03652.
Warning: some vehicles included in this VIN range may
not be involved, so check carefully on the Lamborghini
WEB Portal (at the section named VIN Info) if the cars in
your workshop or in your dealer stock are involved before
performing any other operation.
Information to the field.
As a result of continuous product monitoring, Automobili
Lamborghini Spa has found that on some vehicles the

engine may sporadically stall during tip-in right after
start, so then has made available a new software release for gearbox and engine.

Necessary tools/material.

P/N

Description

Q

ODIS Service diagnosis software updated to release 3.0.1
(or following).

Field solution.
Update the software following the instructions detailed at
the next pages.
Spare parts.
P/N

Description
-

-

Q
-

Replaced parts management.
Store properly and tagged the parts replaced with bar code
form for their identification during Area Manager visits.
Bulletin substitution.
None.
Warranty Claim data.
The warranty reimbursement request for this rework action
will be managed by the following standard Warranty
Claim procedures.
Campaign Code:
Campaign Des.:
Cost code:

Rev.01

L624-A.02.16
Engine & gearbox SW update
50

The information and procedures published below are strictly confidential and intended exclusively for authorized operators and individuals. All copyrights are the property of Automobili Lamborghini S.p.A based on copyright law. The company reserves the right to make
updates and modifications. The reprinting, reproduction, forwarding to unauthorized people and/or to third parties and partial or entire
translation thereof are prohibited without written authorization from Automobili Lamborghini S.p.A.
doc. nr: L/V6_M06 Rev.[02]

1/15

L624A.02.16

To:
Subject:
Date:

Official After Sales Network
Engine & gearbox SW update
March 18,2016

Pages

15

Workshop instructions.

Click “Start tests” to verify the “Last Sync” date.
Update procedure:

The instructions contained in this bulletin are based on
ODIS Service diagnosis software updated to release 3.0.1
(or following) and Lamborghini database 2.5.3 (see
BI.07.15)

2. Please connect a battery charger to the recharge points
available in the front luggage compartment, as shown
in the picture.

Preliminary operations:
1. Make sure to be synchronized with Mirrorserver
checking the “Last Sync” date:
http://mirrorserver/maintenance/diagnosis.py
or:
http://IP_address/maintenance/diagnosis.py
if you did not set up the mirrorserver IP alias.

IMPORTANT
Make sure the latest synchronization was done after
February 14th , 2016.

3. Please connect the VAS5054 interface to the vehicle
OBD plug and to the diagnostic laptop.
Turn the ignition ON.

4. Start ODIS service double-clicking the related icon on
your diagnosis laptop desktop.

Rev.01

The information and procedures published below are strictly confidential and intended exclusively for authorized operators and individuals. All copyrights are the property of Automobili Lamborghini S.p.A based on copyright law. The company reserves the right to make
updates and modifications. The reprinting, reproduction, forwarding to unauthorized people and/or to third parties and partial or entire
translation thereof are prohibited without written authorization from Automobili Lamborghini S.p.A.
doc. nr: L/V6_M06 Rev.[02]

2/15

L624A.02.16

To:
Subject:
Date:

Official After Sales Network
Engine & gearbox SW update
March 18,2016

Pages

15

5. Scroll down the vertical bar on the right.

Click “Adopt”.

Click “OK” to hide the general information window.

6. Click “Start diagnosis”.

Make sure that ODIS can detect the vehicle connection and the key status.

9. Skip the login window clicking “Cancel”.

7. Click “Cancel” for any group system login request.
10. In the following window, click “Without job”.

8. Verify the vehicle identification in the “Basic vehicle
characteristics” window.
Insert Variant and Engine if not already present choosing from the drop down menus.
Leave the checkbox “Using guided fault finding” selected.

Rev.01

The information and procedures published below are strictly confidential and intended exclusively for authorized operators and individuals. All copyrights are the property of Automobili Lamborghini S.p.A based on copyright law. The company reserves the right to make
updates and modifications. The reprinting, reproduction, forwarding to unauthorized people and/or to third parties and partial or entire
translation thereof are prohibited without written authorization from Automobili Lamborghini S.p.A.
doc. nr: L/V6_M06 Rev.[02]

3/15

L624A.02.16

To:
Subject:
Date:

Official After Sales Network
Engine & gearbox SW update
March 18,2016

Pages

15

11. Answer “No” to the “actual comparison” request.

12. At the end of initial operations (see bottom-right status
bar), select “Special functions”.

13. Select “SVM – Direct input: SVM code for problem
related update” clicking the related row.
Click “Perform test…” to execute the SVM function.

15. Click “Yes” to confirm that the inserted code is correct.

16. Click “Done/Continue” to start the data acquisition
from all ECUs.

IMPORTANT
During the SVM operation a battery charger must be
connected.

14. Insert the code L624A0216 in the upper box.
Click “Adopt”.

Rev.01

The information and procedures published below are strictly confidential and intended exclusively for authorized operators and individuals. All copyrights are the property of Automobili Lamborghini S.p.A based on copyright law. The company reserves the right to make
updates and modifications. The reprinting, reproduction, forwarding to unauthorized people and/or to third parties and partial or entire
translation thereof are prohibited without written authorization from Automobili Lamborghini S.p.A.
doc. nr: L/V6_M06 Rev.[02]

4/15

L624A.02.16

To:
Subject:
Date:

Official After Sales Network
Engine & gearbox SW update
March 18,2016

Pages

15

17. Wait until the data acquisition from all ECUs is completed.

20. The communication is then established with the central server.
There might be an update available for up to four
ECUs.
A vehicle with all four ECUs to be updated was used
to create this bulletin:
•
•
•
•

01 – Engine electronics
11 – Engine electronics 2
02 – Gearbox electronics
C2 – Gearbox electronics 2

Click “Done/Continue”.
18. Click “Done/Continue”

21. Click “Done/Continue”.
19. For the online authentication a valid GeKo account is
necessary.
Be sure that the internet connection is correctly established.
Insert your GeKo user name in the field “User name”
and the pin 1324 + current 6 digit code displayed on
your GeKo token in the field “Password”.
Then confirm clicking “Adopt”.

Rev.01

The information and procedures published below are strictly confidential and intended exclusively for authorized operators and individuals. All copyrights are the property of Automobili Lamborghini S.p.A based on copyright law. The company reserves the right to make
updates and modifications. The reprinting, reproduction, forwarding to unauthorized people and/or to third parties and partial or entire
translation thereof are prohibited without written authorization from Automobili Lamborghini S.p.A.
doc. nr: L/V6_M06 Rev.[02]

5/15

L624A.02.16

To:
Subject:
Date:

Official After Sales Network
Engine & gearbox SW update
March 18,2016

Pages

15

22. Click “Done/Continue”.
IMPORTANT
Do not disconnect the hardware interface from OBD
plug and do not switch ignition OFF during the software update!
25. Wait until the update programming of the ECU 01 is
complete.

23. ECU “01 – Engine electronics” software update.

The figure below refers to software versions and part
numbers of the vehicle used as example.
Those data may change depending on the car.
Click “Yes” to check the availability of the software
on the Mirrorserver.

26. Once the update programming has been completed
successfully a message is displayed.

- Click “Done/Continue”.
If the update programming has not been completed or
has been unsuccessful:
- Turn the ignition OFF;
- Wait at least one minute and turn the ignition
ON again;
- Click “Repeat” to restart the update procedure if
it is directly requested by the program; otherwise repeat the procedure from step 12.
24. Verify the new engine ECU software and click “Yes”
to start the update.

Rev.01

The information and procedures published below are strictly confidential and intended exclusively for authorized operators and individuals. All copyrights are the property of Automobili Lamborghini S.p.A based on copyright law. The company reserves the right to make
updates and modifications. The reprinting, reproduction, forwarding to unauthorized people and/or to third parties and partial or entire
translation thereof are prohibited without written authorization from Automobili Lamborghini S.p.A.
doc. nr: L/V6_M06 Rev.[02]

6/15

L624A.02.16

To:
Subject:
Date:

Official After Sales Network
Engine & gearbox SW update
March 18,2016

Pages

15

27. ECU “11 – Engine electronics2” software update.

The figure below refers to the software versions and
the part numbers of the vehicle used as example.
Those data may change depending on the car.
Click “Yes” to check the availability of the software
on the Mirrorserver.
30. Once the update programming has been completed
successfully a message is displayed.
- Click “Done/Continue”.
If the update programming has not been completed or
has been unsuccessful:

28. Verify the available ECU software and click “Yes” to
start the update.

- Turn the ignition OFF;
- Wait at least one minute and turn the ignition
ON again;
- Click “Repeat” to restart the update procedure if
it is directly requested by the program; otherwise repeat the procedure from step 12.

IMPORTANT
Do not disconnect the hardware interface from OBD
plug and do not switch ignition OFF during the software update!
29. Wait until the update programming of the ECU 11 is
complete.

Rev.01

The information and procedures published below are strictly confidential and intended exclusively for authorized operators and individuals. All copyrights are the property of Automobili Lamborghini S.p.A based on copyright law. The company reserves the right to make
updates and modifications. The reprinting, reproduction, forwarding to unauthorized people and/or to third parties and partial or entire
translation thereof are prohibited without written authorization from Automobili Lamborghini S.p.A.
doc. nr: L/V6_M06 Rev.[02]

7/15

L624A.02.16

To:
Subject:
Date:

Official After Sales Network
Engine & gearbox SW update