Classificatio n:

Reference:

EL08-027e

Date:

NTB08-106e

May 17, 2013

UPGRADING HDD NAVIGATION MAP DATA
This bulletin has been amended to update the Map Disc versions to 2013MY (12-13).
No other changes have been made to the body of this bulletin.
Please discard previous versions.

APPLIED VEHICLES: 2008 – 2012 Armada (TA60)
2008 – 2012 Pathfinder (R51)
2009 – 2010 Murano (Z51)

2009 Maxima (A35)
2009 370Z (Z34)
2009 – 2010 G T-R (R35)

SERVICE INFORMATION
The navigation system (if equipped) in the Applied Vehicles listed above has an HDD (Hard
Disc Drive) map data storage system. This bulletin contains the information and instructions
for updating/upgrading the map data with a new version.
An instruction manual for HDD Navigation Updates is also available in ASIST under
Specialty Tools > HD Navi. Tools > Hard Drive Navigation Update Manual.
When new versions of map data are available, customers can purchase a Coupon Number
via the internet at www.nissannavigation.com or by calling NAVTEQ at 1-866-462-8837.
The customer then takes their vehicle, along with the Coupon Number, to a Nissan dealer
to have the new version of map data installed into their navigation system. The time
needed to install the new map data into the vehicle is approximately 30 minutes.
The HDD update kit (P/N: J-48850-A) is required to perform map data updates. One HDD
update kit was shipped to each dealership in the fall of 2008 as part of the essential tool
program. See page 27 for kit details.
Make sure to use the newest Map Data Master Discs (2 disc
set) when performing HDD Navigation Map Data Upgrades.
•

As of the publication date of this bulletin the newest
disc set is 2013MY (12-13).

•

Additional Master Discs are available from TECH-MATE at
1-800-662-2001.

Figure A

Nissan Bulletins are intended for use by qualified technicians, not 'do-it-yourselfers'. Qualified technicians are
properly trained individuals who have the equipment, tools, safety instruction, and know-how to do a job
properly and safely. NOTE: If you believe that a described condition may apply to a particular vehicle, DO
NOT assume that it does. See your Nissan dealer to determine if this applies to your vehicle.

1/27

SERVICE PROCEDURE
IMPORTANT:
•

Make sure your ASIST has been freshly synchronized and all C-III plus updates
have been installed. The HDD (Hard Disc Drive) rewrite software is delivered via
ASIST synchronization.

•

Before the map upgrade can be performed, a Coupon Number must be purchased
from www.nissannavigation.com or by calling NAVTEQ at 1-866-462-8837.

•

Before starting, it is recommend that you check the Current Map Version in the
vehicle using the vehicle’s navigation screen to make sure an upgrade is needed
(see page 26).

Overview of the HDD (Hard Disc Drive) Map Upgrade
This procedure is divided into 7 sections. Complete each section in the following order:
SECTION 1: Installing the Update Map into the Consult PC………………………...Page 3
(This is required only once for each new map version)
SECTION 2: Connecting the Consult PC to the HDD Navigation System………....Page 9
SECTION 3: Generating the Certification Number...………………………………....Page 10
SECTION 4: Acquiring the Install Key...…………………………………………….....Page 14
SECTION 5: Upgrading the Map Data in the HDD Navigation System………....….Page 19
SECTION 6: Disconnecting the Consult PC and CF (Compact Flash) Adapter…...Page 24
SECTION 7: Verifying the Upgrade Result……………………………….…………....Page 26
.

•

Checking Current Map Version in the Vehicle
Using the Vehicle’s Navigation Screen…………………………………...........Page 27

•

HDD update kit (P/N: J-48850-A)………………………………………….……Page 28

2/27

NTB08-106e

SECTION 1: INSTALLING THE UPDATE MAP INTO ASSIST
•

Once the newest version is installed into the Consult PC it can be used to upgrade
many HDD navigation systems. It is not necessary to install the updated map each
time you perform a map data upgrade.

•

If the newest map data is already installed in the Consult PC, you can skip to
Section 2 on page 9.

C-III DVD
drive
1. Connect the DVD drive to the Consult
PC with the USB cable.

Figure 1-1

2. Turn ON the Consult PC.

3. Open / start ASIST.

3/27

NTB08-106e

4. Select Specialty Tools, Then HD Navi. Tools.

Step 4

Figure 1-2

5. Select Install Map Update

Step 5

Figure 1-3

4/27

NTB08-106e

6. Select Installing updated map
HDD Rewrite Application

Please select work items.
Step 6

Installing
updated map

Generation and
confirmation of
certification No.

Map update

CDDB update

Map version
display

Setting/History

4

Program update
EXIT
Figure 1-4
7. Insert the Map Data Master Disc 1 into the DVD drive.
8. Confirm the correct name of the DVD drive is displayed (see Figure 1-5).
•

“E” is likely the correct name for the DVD drive.

•

The DVD drive name may be different depending on the drive configuration of your
Consult PC.

9. Select START

Step 8
Step 9

Figure 1-5
5/27

NTB08-106e

•

Installation of the update map will start and a progress screen will display.

•

Installation will take several minutes.

Figure 1-6

•

At about 35% this message will display:
Information

Please Inset Disc No. 2 in Drive.
NO

YES

Figure 1-7

•

When you get the above message, remove Disc 1; install Disc 2; then select YES.

6/27

NTB08-106e

•

When installation is complete the screen shown in Figure 1-8 will display.

10. Select OK

Step 10

Figure 1-8

11. Select EXIT
HDD Rewrite Application

Please select work items.
Installing
updated map

Generation and
confirmation of
certification No.

Map update

CDDB update

Map version
display

Setting/History

Program update
Step 11

EXIT

Figure 1-9

7/27

NTB08-106e

12. Remove Disc 2 from the DVD drive.

13. Select the Safely Remove Hardware icon on the “system tray” which is displayed in the
bottom right of the Consult PC screen.
•

You may need to click on the “expand arrow” to expand the icon selections.

Step 13

System tray

Expand
arrow

Figure 1-10

14. Select Safely remove USB Mass Storage Device - Drive (E:)
•

The drive name will likely be E, but may be different depending on the drive
configuration of your Consult PC.

Figure 1-11

15. Disconnect the DVD drive from the Consult PC.

C-III DVD
drive

Figure 1-12

8/27

NTB08-106e

SECTION 2: CONNECTING the Consult PC TO THE HDD NAVIGATION SYSTEM
•

All navigation components must be installed in the vehicle and connected correctly.

•

Make sure the vehicle battery is charged and connected.

•

Do not touch the CF (Compact Flash) adapter with wet hands.

CAUTION:
• Do not turn the ignition ON when the Consult PC is connected to the navigation
system with the CF adapter.
•

Obey the following instructions; otherwise the CF Adapter, CF card slot, or
navigation system may be damaged.

1. Make sure the ignition is OFF.

2. Close any applications that are running on the Consult PC.
•

If the Consult PC is OFF, leave it OFF for now.

3. Connect USB cable to the Consult PC.
•

Make sure connector is fully inserted.

Figure 2-1

4. Connect the other end of the USB cable to the CF
adapter.
•

Make sure connector is fully inserted.
Figure 2-2

5. Carefully insert the CF adapter into the CF card
slot of the vehicle audio/navigation system.
•

Label side should be UP.

•

Insert it all the way (firmly), to its stop.
Figure 2-3
9/27

NTB08-106e

SECTION 3: GENERATING THE CERTIFICATION NUMBER
•

The Certification Number is different for each HDD (Hard Disc Drive) navigation
system. Make sure you are connected with the CF adaptor to the system (vehicle)
that you will be updating.

1. Turn ON the Consult PC.

2. Open / start ASIST.

3. Select Specialty Tools, Then HD Navi. Tools.

Step 3

Figure 3-1

10/27

NTB08-106e

4. Select Install Map Update

Step 4

Figure 3-2

5. Select Generation and confirmation of Certification number.
HDD Rewrite Application

Please select work items.
Step 5
Installing
updated map

Generation and
confirmation of
certification No.

Map update

CDDB update

Map version
display

Setting/Histor
y

4

Program update
EXIT
Figure 3-3

NOTE: If the HDD Rewrite application was open/running when you connected to the
navigation system (plugged in the CF adapter), the navigation system may not be
recognized and you may get an error message. In this case, exit/close ASIST, then start
it again (reopen it).

11/27

NTB08-106e

6. Click START

Step 6

Figure 3-4

NOTE: If you get the message shown in Figure 3-5:
•

The map data installed in your Consult PC is the same or older than the map data in
the vehicle. The map update may not be needed.
a. Skip to Section 6 on page 23 (disconnect the Consult PC from the vehicle
navigation system).
b. Check the map version in the vehicle (see page 26).

Figure 3-5

12/27

NTB08-106e

7. Write down the Certification Number.

8. Select OK

HDD Rewrite Application

Generation and confirmation of Certification No.

Certification No. is
Step 7

XXXX

_ XXXX

Step 8

OK

Figure 3-6

13/27

NTB08-106e

SECTION 4: ACQUIRING THE INSTALL KEY
•

Before starting this section, you need:
¾ A Coupon Number (purchased from NAVTEQ via the Internet at
www.nissannavigation.com or by calling NAVTEQ at 1-866-462-8837).
¾ A Certification No. (generated from the vehicle HDD navigation unit in Section 3).

•