55°F / 13°C

Amp Draw
Negligible

(1) Current draw shown is maximum
sustained amperage.

Optional Thermostatic
Shut-Off Kit 12 & 24 Volt

600 WATT
24 Volt

12 Volt

450 WATT
24 Volt

12 Volt

300 WATT
24 Volt

12 Volt

150 WATT
24 Volt

(2) Minimum alternator capacity is
only a guideline. Total system
load analysis is required for
accurate battery/charging system
specification. Refer to maximum
sustained current draw and consult
your vehicle manufacturer for
advisement whenever adding any
aftermarket auxiliary current load.

18

Item Description

Part Number

1

Black Jumper 14 Gauge

D3061-1677

2

12V Lighted Toggle Switch
24V Lighted Toggle Switch

D3061-1582
D3061-1584

3

Optional Thermostat Kit

D3065-2338

4

3-Wire Harness Kit

D3061-1735

5

Wire Jumper Magnetic
Switch

D3065-2360

6

#10 Jumper Main Power

D3061-1664

7

12V Magnetic Switch
24V Magnetic Switch

D3061-1573
D3061-1575

8

12V 60 Amp Circuit Breaker
24V 60 Amp Circuit Breaker

D3061-1560
D3061-1565

9

#4 Jumper Main Power–47"

D3061-1638

10

Wire Jumper Mod.
Ground–96"

D3065-2357

11

Insulating Boot

D3065-2284

U.S/CAN: 1-800-654-5382 fax: 763-972-2873
The Netherlands: +31 165 55 9245 fax: +31 165 54 9640

Fuel & Fluid Heaters

HOT FOX™ HYDRAULIC FLUID HEATER
Used on applications which require maximum heat exchangers in a concentrated area.
NOTE: For extreme cold weather applications, multiple hydraulic HOT FOX™ fluid heaters may be desired.

Part Number
SHH-1844-09
SHH-1844-11
SHH-1844-12
SHH-1844-13
SHH-1844-16
SHH-1844-19
SHH-1844-21
SHH-1844-23
SHH-1844-25
SHH-1844-26

Total Length
(Inch/mm)
8-1/4 / 210
10-1/4 / 260
11-1/4 / 286
12-1/4 / 311
15-1/4 / 387
18-1/4 / 464
20-1/4 / 514
22-1/4 / 565
24-1/4 / 616
25-1/4 / 641

Maximum Tank
Capacity (usg/L)
8 / 30
10 / 38
12 / 45
14 / 53
17 / 64
20 / 76
22 / 83
25 / 95
28 / 106
32 / 121

WARNING: Failure to use recommended reinforcement kits or providing additional
structural support to heater may cause tank to crack, leading to fluid leakage.

Installation: The SHH Series HOT FOX™ hydraulic fluid heater can mount into a standard USA fuel sending gauge opening.

• Non-Reinforced Openings in tanks manufactured of 14 gauge (0.075"/1.9mm) and lighter steel or 0.100"/2.5mm and lighter aluminum, the
appropriate adapter kit KT-826F, KT-827C or KT-831CS is recommended for additional structural support.

• Extreme Vibration or Horizontal Mounting, the appropriate adapter kit A-1721 or A-2060 is recommended for additional structural support.

ROUND TANK

KT-827C for 22"-29"/559-737mm Dia.
KT-831CS for 14"-21"/356-533mm Dia.
Adapts standard Arctic Fox® fuel
heaters mount to Hot Fox™ mount.
Reinforces tank opening.

KIT COMPONENTS

Adapter Plate 6"/152mm Square (1)
A-827 for KT-827C
A-831 for KT-831CS
Backing Plates (2) A-1795
Clips (4) A-649
Gasket (1)—A-611
Mounting Bolts (12) – A-610
Template (1)—A-708

FLAT TANKS

THREADED ADAPTER

Fits 1-1/2" & 2" NPT Couplings

KT-826F

Adapts standard Arctic Fox® fuel
heater mount to Hot Fox™
mount. Reinforces tank opening.

A-1721
(To –40°F/C)
Parts Included
(1) A-1792 Gasket
(2) A-1726 O-Ring

KIT COMPONENTS

Adapter Plate 6"/152mm Square
(1) A-826
Backing Plates (2) A-2025
Clips (4) A-649
Gasket (1)—A-611
Mounting Bolts (12) – A-610
Template (1)—A-708

U.S/CAN: 1-800-654-5382 fax: 763-972-2873
The Netherlands: +31 165 55 9245 fax: +31 165 54 9640

Item
1

A-1721F
(To –90°F/-67°C)
Parts Included
(1) A-1792 Gasket
(2) A-2758 O-Ring

WELD-IN ADAPTER

For Fuel or Hydraulic Tanks
A-2060 (Steel)
A-2060-A (Alum.)
(To –40° F/C)
Parts Included
(1) A-1792 Gasket
(2) A-1726 O-Ring

Qty
Description
5 #10-32 UNF x 1.0 Cap Screw

2
3
4

5
2
1

5

1

Stainless Steel Washer
Self Drill / Tap Screw
HOT FOX™
Fuel Warmer Gasket
Back Up Plate / Template

A-2060F
A-2060-AF
(To –90° F/-67°C)
Parts Included
(1) A-1792 Gasket
(2) A-2758 O-Ring

Part No.
A-857
A-861
A-608
A-841
A-834

19

Fuel & Fluid Heaters

Heats hydraulic fluid, water and other fluids to improve productivity
BENEFITS

SPECIFICATIONS

VERSATILE

• Reduces cold weather viscosity
• Increases productivity – reduces idle
equipment and workers waiting for
hydraulic to warm up
• Reduces pump cavitation and
resulting damage
• Versatile design for use on various
equipment
• Ample coolant flow due to large
(3/4" NPT) connectors

• All stainless steel construction
• Large surface area exposed to fluid
to maximize heat rise
• Threads into standard 2" NPT female
pipe thread or standard 2" Straight
Thread-O-Ring (STOR) coupling

•
•
•
•

Logging
Construction
Mining
Utility and Maintenance vehicles

• 3/4" NPT coolant connections
• 5-year-600,000 mile (965,000km)
warranty
• Ability to install multiple units for
larger tanks or faster heat rise
• Install horizontally at bottom of tank

Part Number
H-4000-8
H-4000-8-STOR
H-4000-12
H-4000-12-STOR
H-4000-16
H-4000-16-STOR
H-4000-20
H-4000-20-STOR

"A" Dimension
Nominal
7 inches
178 mm
11 inches
280 mm
15 inches
381 mm
19 inches
483 mm

"B" Dimension
Nominal
10 inches
254 mm
14 inches
356 mm
18 inches
457 mm
22 inches
559 mm

H-4000-24
H-4000-24-STOR

23 inches
584 mm

26 inches
660 mm

Typical Application
Surface Area
BTU/hr
(ambient air temp)
Nominal
Nominal (1) to -20°F / -29°C (2)**
105 in2
Water 4,200
Up to 20 US gallons
Oil 2,100
76 Liters
8 dm2
2
180 in
Water 7,200
Up to 35 US gallons
Oil 3,600
133 Liters
12 dm2
250 in2
Water 10,000 Up to 50 US gallons
Oil 5,000
190 Liters
16 dm2
315 in2
Water 13,000 Up to 63 US gallons
Oil 6,500
239 Liters
20 dm2
385 in2
24 dm2

Water 16,000
Oil 8,000

Up to 77 US gallons
292 Liters

Typical Application
(ambient air temp) to
-40°F / -40°C (2)**
Up to 8 US gallons
30 Liters
Up to 14 US gallons
53 Liters
Up to 19 US gallons
72 Liters
Up to 25 US gallons
90 Liters
Up to 30 US gallons
113 Liters

(1)

Nominal BTU/hr based upon 180°F / 82°C Coolant flowing at 5 US Gallons / 19 Liters per minute.
Water­—beginning temperature at +35°F / + 2°C
Oil—ISO 32 Hydraulic Oil beginning temperature -20°F / 29°C

(2)

Actual temperature rise will be affected by factors such as coolant temperatures and flow rate, specific heat capacity
of fluids and air movement around reservoir.
**
Contact Arctic Fox Application Engineering for estimated temperature rise for your specific application.

WELD ON TANK ADAPTERS
Part Number
Description
A-3228HD
A-3228AHD
A-3228HD-STOR
V6216
A-5878SSHD
IS43THCK
TWF-32
TWF-32N

20

Steel—Schedule 80 2" NPT Female Coupling
Aluminum T-6061—Schedule 80 2" NPT
Female Coupling
Steel—Combination 32 STOR & 2" NPT
Steel—Half Coupling—32 STOR
Stainless Steel—Half Coupling—32 STOR
Stainless Steel—2" NPT Half Coupling 300#
Steel—Flange 32 STOR
Steel—Flange 2" NPT

Application
Preferred for most installations on steel tanks
Preferred for most installations of aluminum tanks
May be used to install either style of Hydra Liner
Used when external tank clearance is limited
Used when external tank clearance is limited
Preferred for most installations on Stainless Steel Tanks
Used when external clearance is limited
Used when external clearance is limited

U.S/CAN: 1-800-654-5382 fax: 763-972-2873
The Netherlands: +31 165 55 9245 fax: +31 165 54 9640

Fuel & Fluid Heaters

HYDRAULIC FLUID HEATERS & ACCESSORIES

Fuel & Fluid Heaters
Fuel & Fluid Heaters

HYDRAULIC FLUID HEATER & ACCESSORIES
MINI HEAT EXCHANGER
Utilizes engine coolant to heat engine oil pans and small hydraulic reservoirs 1-5 gallons/4-19 Liters

Part Number
H-2697-6SS
H-2697-8SS
H-2697-10SS

Adapter Type
3/4" NPT
3/4" NPT
3/4" NPT

Tube Diameter
7/8" / 22mm
7/8" / 22mm
7/8" / 22mm

Material
Stainless Steel
Stainless Steel
Stainless Steel

DIM "A"
6 / 152mm
8 / 203mm
10 / 254mm

DIM "B"
7 / 178mm
9 / 229mm
11 / 279mm

CUSTOM HEAT EXCHANGERS

1. Provide the following information to receive a quote
a. Exact dimensions and tank clearance (I.e. sketch, blueprint, IGES CAD file? Tank and system capacity)
b. Type of vehicle or machine
c. Type of fluid to be heated
Example of Custom Heater with
By-Pass Thermostat for Customer
d. Maximum allowable temperature of fluid to be heated. Is thermostat required?
Specified Tank Configuration
e. Total coolant capacity
f. Does equipment have a fuel fired coolant pre-heater? What is the BTU size capacity?
g. Does the application only require maintaining existing reservoir heat or will system
be ”cold soaked” and fluid temperature rise be required? Please note original
fluid temperature and desired temperature after one hour of heating.
h. Is tank pressurized or used on aerial man lift?
2. Fax or call Arctic Fox with above information
Phone: (800) 654-5382 or (763) 972-2758—Fax: (763) 972-2873.
3. Arctic Fox will design and quote for this specific reservoir.
4. A design print and customer authorization will be sent to customer. If approved, customer will indicate so by returning
.signed customer authorization form to Arctic Fox. After receipt of signed authorization, orders for the custom heat
exchanger will be filled. Allow 4 to 6 weeks after receipt of signed authorization.

A-1714 MOUNTING PLATE BUSHING WITH O-RING

Used on applications where a reservoir is pressurized or when a
heater is mounted below the fluid level. May be used instead of
standard A-612 bushing to achieve seal under pressure.
Part No.

Description

A-639

Compression Nut

A-621

Split Ring Ferrule—Package of 4

A-628

Locking Nut

A-617

O-Ring kit—Package
contains 4 White & 4 Black

A-616

Copper Washer

A-1714

Hydraulic Bushing

A-1725

O-Ring

U.S/CAN: 1-800-654-5382 fax: 763-972-2873
The Netherlands: +31 165 55 9245 fax: +31 165 54 9640

FUEL & HYDRAULIC TANK WELD-ON ADAPTERS
Part No.
A-626