Swallowing: Swallowing small amounts of this material during normal handling is not likely to cause harmful
effects. Swallowing large amounts may be harmful.
Inhalation: Breathing of vapor or mist is possible.
Licensed to Excelda Manufacturing, Inc.

ANSI Z400.1 format

MATERIAL SAFETY DATA SHEET
HD GO-5 50/50 Coolant

Page: 2
Printed: 10/28/2013
Revision: 10/28/2013

Signs and Symptoms Of Exposure

Exposure to this product and/or its components may be evidenced by the following symptoms: nausea, vomiting,
diarrhea, irritation or discomfort, giddiness, liveliness, light-headed feeling, dizziness, drowsiness, weakness,
fatigue, headache, unconsciousness and/or involuntary eye movement.
Medical Conditions Generally Aggravated By Exposure

No data available.
OSHA Hazard Classes:

HEALTH HAZARDS : Toxic, Irritant
PHYSICAL HAZARDS : No Physical Hazards
TARGET ORGANS & EFFECTS: Kidney, Liver, Central Nervous System

4. First Aid Measures
Emergency and First Aid Procedures

Eyes: If symptoms develop, immediately move individual away from exposure and into fresh air. Flush eyes
gently with water for at least 15 minutes while holding eyelids apart; seek immediate medical attention.
Skin: Remove contaminated clothing. Wash exposed area with soap and water. If symptoms persist, seek
medical attention. Launder clothing before reuse.
Swallowing: Seek medical attention. If individual is drowsy or unconscious, do not give anything by mouth;
place individual on the left side with the head down. Contact a physician, medical facility, or poison control
center for advice about whether to induce vomiting. If possible, do not leave individual unattended.
Inhalation: If symptoms develop, immediately move individual away from exposure and into fresh air. Seek
immediate medical attention; keep person warm and quiet. If person is not breathing, begin artificial respiration.
If breathing is difficult, administer oxygen.
Note to Physician

This product contains ethylene glycol. Ethanol decreases the metabolism of ethylene glycol to toxic metabolites.
Ethanol should be administered as soon as possible in cases of severe poisoning since the elimination half-life of
ethylene glycol is 3 hours. If medical care will be delayed several hours, give the patient three to four 1-ounces
oral "shots" of 86 proof, or higher whiskey before or during transport to the hospital. Hemodialysis effectively
removes ethylene glycol and its metabolites from the body. Effects of acute ethylene glycol poisoning appear in
three fairly distinct stages. The initial stage occurs shortly after exposure, lasts 6-12 hours, and is characterized
by central nervous system effects (transient exhilaration, nausea, vomiting, and in severe cases, coma,
convulsions, and possible death. The second stage lasts from 12-36 hours after exposure and is initiated by the
onset of coma. This phase is characterized by tachypnea, tachycardia, mild hypotension, cyanosis, and in severe
cases, pulmonary edema, bronchopneumonia, cardiac enlargement, and congestive failure. The final stage
occurs 24-72 post-exposure and is characterized by renal failure ranging from a mild increase in blood urea
nitrogen and creatinine followed by recovery to complete anuria with acute tubular necrosis that can lead to
death. Oxaluria is found in most cases. The most significant laboratory finding in ethylene glycol intoxication
is severe metabolic acidosis.

5. Fire Fighting Measures
Flash Pt:

> 200.00 F (93.3 C)

Explosive Limits:

LEL: No data.

Autoignition Pt:

No data available.

UEL: No data.

Fire Fighting Instructions

Wear a self-contained breathing apparatus with a full facepiece operated in the positive pressure demand mode
with appropriate turn-out gear and chemical resistant personal protective equipment.

Licensed to Excelda Manufacturing, Inc.

ANSI Z400.1 format

MATERIAL SAFETY DATA SHEET
HD GO-5 50/50 Coolant

Page: 3
Printed: 10/28/2013
Revision: 10/28/2013

Flammable Properties and Hazards

Never use welding or cutting torch on or near drum (even empty) because product (even just residue) can ignite
explosively.
Hazardous Combustion Products

Carbon dioxide, carbon monoxide, and various hydrocarbons.
Extinguishing Media

Alcohol foam, carbon dioxide, dry chemical.
Unsuitable Extinguishing Media

No data available.

6. Accidental Release Measures
Steps To Be Taken In Case Material Is Released Or Spilled

Small Spill: Absorb liquid on vermiculite, floor absorbent or other absorbent material.
Large Spill: Persons not wearing protective equipment should be excluded from area of spill until clean-up has
been completed. Stop spill at source, dike area of spill to prevent spreading, pump liquid to salvage tank.
Remaining liquid may be taken up on sand, clay, earth, floor absorbent, or other absorbent material and shoveled
into containers.

7. Handling and Storage
Precautions To Be Taken in Handling

Containers of this material may be hazardous when emptied. Since emptied containers retain product residues
(vapor, liquid, and/or sold), all hazard precautions given in the data sheet must be observed.
Precautions To Be Taken in Storing

No data available.

8. Exposure Controls/Personal Protection
Respiratory Equipment (Specify Type)

If workplace exposure limit(s) of product or any component is exceeded, a NIOSH/MSHA approved air supplied
respirator is advised in absence of proper environmental control. OSHA regulations also permit other
NIOSH/MSHA respirators (negative pressure type) under specified conditions. Engineering or administrative
controls should be implemented to reduce exposure. If needed use a NIOSH/MSHA jointly approved dust
respirator.
Eye Protection

Chemical splash goggles in compliance with OSHA regulations are advised; however, OSHA regulations also
permit other type safety glasses.
Protective Gloves

Wear resistant gloves such as neoprene, nitrile rubber, polyvinyl chloride.
Other Protective Clothing

To prevent repeated or prolonged skin contact, wear impervious clothing and boots.
Engineering Controls (Ventilation etc.)

Provide sufficient mechanical (general and/or local exhaust) ventilation to maintain exposure below TLV(s).
Work/Hygienic/Maintenance Practices

No data available.

9. Physical and Chemical Properties
Physical States:

[ ] Gas

Melting Point:

No data.

Licensed to Excelda Manufacturing, Inc.

[ X ] Liquid

[ ] Solid

ANSI Z400.1 format

MATERIAL SAFETY DATA SHEET
HD GO-5 50/50 Coolant
Boiling Point:

No data.

Autoignition Pt:

No data.

Flash Pt:

> 200.00 F (93.3 C)

Specific Gravity (Water = 1):

1.07 - 1.08

Vapor Pressure (vs. Air or mm Hg):

No data.

Vapor Density (vs. Air = 1):

No data.

Evaporation Rate:

No data.

Solubility in Water:

Complete

Percent Volatile:

No data.

pH:

7.5 - 8.5

Page: 4
Printed: 10/28/2013
Revision: 10/28/2013

at 77.0 F (25.0 C)

Appearance and Odor

Yellow liquid with bitter taste.

10. Stability and Reactivity
Stability:

Unstable [

]

Stable [ X ]

Conditions To Avoid - Instability

None known.
Incompatibility - Materials To Avoid

Strong oxidizing agents.
Hazardous Decomposition Or Byproducts

Carbon dioxide, carbon monoxide, and various hydrocarbons.
Hazardous Polymerization:

Will occur [

]

Will not occur [ X ]

Conditions To Avoid - Hazardous Polymerization

Will not occur.

11. Toxicological Information
Toxicological Information

No data available.
Chronic Toxicological Effects

No data available.
Carcinogenicity/Other Information

Ethylene glycol has caused birth defects in animal studies at high oral doses.
Carcinogenicity:

NTP? No

IARC Monographs? No

OSHA Regulated? No

12. Ecological Information
General Ecological Information

No data available.

13. Disposal Considerations
Waste Disposal Method

Dispose of in accordance with all applicable local, state and federal regulations. Destruction by liquid
incineration is recommended.

14. Transport Information
LAND TRANSPORT (US DOT)
DOT Proper Shipping Name

Not Regulated

Additional Transport Information

The Reportable Quantity (RQ) for Ethylene Glycol is 5539 lbs.
The information contained in Section 14 applies only to the material when packaged in non-bulk containers with
Licensed to Excelda Manufacturing, Inc.

ANSI Z400.1 format

Page: 5

MATERIAL SAFETY DATA SHEET
HD GO-5 50/50 Coolant

Printed: 10/28/2013
Revision: 10/28/2013

a capacity of less than 5000 lbs. If this product is shipped in bulk other regulations may apply.

15. Regulatory Information
US EPA SARA Title III
Chemical Name
1.

Ethylene glycol

2.

Diethylene glycol

3.

Benzenemethanaminium,
N-[2-[(2,6-Dimethylphenyl)amino]-2-oxo

4.

Boron sodium oxide (B4Na2O7)

CAS #

Sec.304 RQ

Sec.313 (TRI)

Sec.110

107-21-1 No

Sec.302 (EHS)

Yes 5000 LB

Yes

No

111-46-6 No

No

No

No

3734-33-6 No

No

No

No

1330-43-4 No

No

No

No

CAS #

US EPA CAA, CWA, TSCA
EPA CWA NPDES

EPA TSCA

CA PROP 65

1.

Chemical Name
Ethylene glycol

107-21-1 HAP

EPA CAA

No

Inventory, 4 Test

No

2.

Diethylene glycol

111-46-6 No

No

Inventory

No

3.

Benzenemethanaminium,
N-[2-[(2,6-Dimethylphenyl)amino]-2-oxo

3734-33-6 No

No

Inventory

No

4.

Boron sodium oxide (B4Na2O7)

1330-43-4 No

No

Inventory

No

SARA (Superfund Amendments and
Reauthorization Act of 1986) Lists:
Sec.302:

EPA SARA Title III Section 302 Extremely Hazardous Chemical with TPQ. * indicates 10000
LB TPQ if not volatile.

Sec.304:

EPA SARA Title III Section 304: CERCLA Reportable + Sec.302 with Reportable Quantity. **
indicates statutory RQ.

Sec.313:

EPA SARA Title III Section 313 Toxic Release Inventory. Note: -Cat indicates a member of a
chemical category.

Sec.110:

EPA SARA 110 Superfund Site Priority Contaminant List

TSCA (Toxic Substances Control
Act) Lists:
Inventory:

Chemical Listed in the TSCA Inventory.

5A(2):

Chemical Subject to Significant New Rules (SNURS)

6A:

Commercial Chemical Control Rules

8A:

Toxic Substances Subject To Information Rules on Production

8A CAIR:

Comprehensive Assessment Information Rules - (CAIR)

8A PAIR:

Preliminary Assessment Information Rules - (PAIR)

8C:

Records of Allegations of Significant Adverse Reactions

8D:

Health and Safety Data Reporting Rules

8D TERM:

Health and Safety Data Reporting Rule Terminations

12(b):

Notice of Export

Other Important Lists:
CWA NPDES:

EPA Clean Water Act NPDES Permit Chemical

CAA HAP:

EPA Clean Air Act Hazardous Air Pollutant

CAA ODC:

EPA Clean Air Act Ozone Depleting Chemical (1=CFC, 2=HCFC)

CA PROP 65:

California Proposition 65

International Regulatory Lists:
EPA Hazard Categories:

This material meets the EPA 'Hazard Categories' defined for SARA Title III Sections 311/312 as indicated:

Licensed to Excelda Manufacturing, Inc.

ANSI Z400.1 format

MATERIAL SAFETY DATA SHEET
HD GO-5 50/50 Coolant

Page: 6
Printed: 10/28/2013
Revision: 10/28/2013

[X] Yes [ ] No Acute (immediate) Health Hazard
[X] Yes [ ] No Chronic (delayed) Health Hazard
[ ] Yes [X] No Fire Hazard
[ ] Yes [X] No Sudden Release of Pressure Hazard
[ ] Yes [X] No Reactive Hazard
Regulatory Information

TSCA: All ingredients in this product are listed on the TSCA Inventory or are otherwise exempt.
CA Prop 65: This product is not known to contain any chemicals known to the State of California to cause
cancer, birth defects or other reproductive harm.
Regulatory Information Statement

The information contained herein is based on data considered accurate. However, no warranty is expressed or
implied regarding the accuracy of this data or the results to be obtained from the use thereof. Vendor assumes no
responsibility for injury to vendee or third person proximately caused by the material if reasonable safety
procedures are not adhered to as stipulated in the data sheet. Additionally, vendor assumes no responsibility for
injury to vendee or third persons proximately caused by abnormal use of the material even if reasonable safety
procedures are followed. Furthermore, vendee assumes all risk in use of the material.

16. Other Information
Company Policy or Disclaimer

THIS INFORMATION IS FURNISHED WITHOUT WARRANTY, EXPRESSED OR IMPLIED, EXCEPT
THAT IS ACCURATE TO THE BEST KNOWLEDGE OF HINO MOTOR SALES USA. THE DATA ON
THIS SHEET RELATES ONLY TO THE SPECIFIC MATERIAL DESIGNATED HEREIN. HINO MOTOR
SALES USA. ASSUMES NO LEGAL RESPONSIBILITY FOR USE OR RELIANCE UPON THIS DATA.

Licensed to Excelda Manufacturing, Inc.

ANSI Z400.1 format

Page: 1

MATERIAL SAFETY DATA SHEET
Ceramic Anti-Seize
Flammability

Health

1

1

Instability

Printed: 10/28/2013
Revision: 10/25/2013

1

Date Created: 10/24/2012

Special Hazard

1. Product and Company Identification
Product Code:

GSC-0034-12

Product Name:

Ceramic Anti-Seize

Manufacturer/Supplier/Distributor Information
Company Name:

Hino Motor Sales USA, Inc.
41180 Bridge St.
Novi, MI 48375

Phone Number:

(248)699-9300

Fax Number:

(248)699-9310

Part Number: