L-SB-0037-20

October 8, 2020

2021 UX 200, UX 250h Pre-Delivery Service (PDS)
Service
Category

General

Section

Pre-Delivery Service

Market USA

Applicability
YEAR(S)

MODEL(S)

2021

UX200, UX250H

ADDITIONAL INFORMATION

Introduction

This bulletin contains the vehicle specific pre-delivery services for 2021 model year UX 200 and
UX 250h vehicles. Additionally, refer to the applicable Pre-Delivery Service (PDS) Check Sheet
for services to be performed.

Warranty Information
OP CODE

DESCRIPTION

TIME

OFP

T1

T2

N/A

Not Applicable to Warranty

–

–

–

–

Procedures



D/C Cut Fuse Installation ..................................................................................................... 2



Deletion of Vehicle Alert History ........................................................................................... 3



Tire Pressure Warning System (TPWS) Initialization ............................................................ 3



Seating Position Control ECU Initialization* ......................................................................... 4



Memorize Steering Angle Neutral Point ................................................................................ 4



Parking Support Brake System Calibration* .......................................................................... 4



Compass Calibration* .......................................................................................................... 4



Front and Rear Emergency Towing Eyelet Removal and Hole Cover Installation* ............... 5



Front License Plate and Mounting Bracket Installation* ........................................................ 8



Installation of Rubber Body Plugs* ..................................................................................... 10

*If Applicable

© 2020 Lexus, a division of Toyota Motor Sales, USA

Page 1 of 10

L-SB-0037-20

October 8, 2020

Page 2 of 10

2021 UX 200, UX 250h Pre-Delivery Service (PDS)
D/C Cut Fuse Installation

To minimize battery discharge during transportation and storage, the D/C cut fuse (30A) has
been removed at the assembly plant and temporarily stored in the blank space of the relay block
in the engine compartment. During PDS, reinstall the D/C cut fuse (30A) into its original location
and clear ALL related Diagnostic Trouble Codes (DTCs).
Figure 1.

A

B

C
2

2
1

1

A

Relay Block

1

Remove D/C Cut Fuse (30A)

B

Gasoline Vehicles

2

Install D/C Cut Fuse (30A) (Original Location)

C

Hybrid Vehicles

NOTE
While the vehicle is stored at the dealership, disconnect the negative (–) battery terminal to prevent
battery discharge. Refer to Service Bulletin No. L-SB-0017-20, Battery Maintenance During PDS, for
battery maintenance information.

© 2020 Lexus, a division of Toyota Motor Sales, USA

L-SB-0037-20

October 8, 2020

Page 3 of 10

2021 UX 200, UX 250h Pre-Delivery Service (PDS)
Deletion of Vehicle Alert History

As the D/C cut fuse is removed, the communication between the various ECUs is interrupted.
When the D/C fuse is reinstalled, the communication status is restored, but Lexus Enform
Service Connect may store malfunction history in the form of vehicle alert history.
Therefore, it is necessary to operate the multi-display and delete the vehicle alert history AFTER
installing the D/C cut fuse during PDS at the dealership.
Deletion Procedure

1. Turn the engine switch (power switch) to the ON position (ON mode).
2. Push the Menu switch on the remote touch device.
3. On the multi-display, enter the following menus: Info – Vehicle Alert History.
4. If there is vehicle alert history stored, perform the Delete History operation.
HINT
If there is no vehicle alert history stored, the system will display a message stating
“There is no vehicle alert history.”

5. When the vehicle alert history deletion confirmation screen is displayed, select Yes.
HINT
If there is no vehicle alert history stored, the system will display a message stating
“There is no vehicle alert history.”

6. Turn the engine switch (power switch) to the OFF position (OFF mode).

Tire Pressure Warning System (TPWS) Initialization

Refer to the applicable Repair Manual for the TPWS initialization procedure.
Note the spare tire does NOT have a TPWS sensor.
NOTE
To adjust the tire pressure correctly when the outside temperature is significantly colder than shop
temperature, perform a Health Check using Techstream and select the compensation tire pressure
checkbox. Compensation pressures will display on the Health Check results screen. Adjust the tire
pressure when the tires are cold.

© 2020 Lexus, a division of Toyota Motor Sales, USA

L-SB-0037-20

October 8, 2020

Page 4 of 10

2021 UX 200, UX 250h Pre-Delivery Service (PDS)
Seating Position Control ECU Initialization

Refer to the applicable Repair Manual for the seating position control ECU initialization
procedure (procedure 2).

Memorize Steering Angle Neutral Point

As a result of the removal of the D/C cut fuse, the power source to the steering angle sensor is
cut off. When the D/C cut fuse is reinstalled, the parking assist monitor system will be operative,
but it cannot display guidelines to assist parking operation because the center position
recognized by the steering angle sensor may not be in an initial position. Therefore, perform
steering angle neutral point initialization AFTER installing the D/C cut fuse during PDS.
Refer to the applicable Repair Manual for the steering angle neutral point
initialization procedure.

Parking Support Brake System Calibration

As a result of the removal of the D/C cut fuse, the steering angle sensor power source is cut off.
When the D/C cut fuse is reinstalled, the center position recognized by the steering angle sensor
may not be the appropriate position. Therefore, it is necessary to perform intelligent clearance
sonar system calibration AFTER installing the D/C cut fuse during PDS.
Refer to the applicable Repair Manual for the intelligent clearance sonar system
calibration procedure:


Driving Method



Techstream Method (procedure 4)

Compass Calibration

Refer to the applicable Repair Manual for the calibration procedure for vehicles equipped with
a compass.
NOTE
 Do not perform calibration of the compass in a place where the Earth's magnetic field is subject to
interference (underground parking, under a steel tower, between buildings, roof parking, near a
railroad crossing, near a large vehicle, etc.).
 During calibration, do not operate electric systems (moonroof, power windows, etc.) as they may
interfere with the calibration.
 The dot on the compass display disappears when calibration is completed.

© 2020 Lexus, a division of Toyota Motor Sales, USA

L-SB-0037-20

October 8, 2020

Page 5 of 10

2021 UX 200, UX 250h Pre-Delivery Service (PDS)
Front and Rear Emergency Towing Eyelet Removal and Hole Cover Installation

1. Remove the front and rear emergency towing
eyelets from the front and rear bumpers by
turning them counterclockwise.

Figure 2.

NOTE
If it is difficult to loosen the front emergency
towing eyelet, use a steel bar.
1

2

1

Front Emergency Towing Eyelet

2

Rear Emergency Towing Eyelet

© 2020 Lexus, a division of Toyota Motor Sales, USA

L-SB-0037-20

October 8, 2020

Page 6 of 10

2021 UX 200, UX 250h Pre-Delivery Service (PDS)
Front and Rear Emergency Towing Eyelet Removal and Hole Cover Installation

2. Place one of the removed emergency towing eyelets into the luggage tray in the
luggage compartment.
NOTE
Dispose of the other removed emergency towing eyelet.

Figure 3.

A

B