NHTSA ID Number: 10181356
Manufacturer Communication Number: SCB 11 M 090
TSB/Document Date: 2020-10-20
Summary
Vehicle Software Update to Platform 9.5
10
9
ECM Software Update:
31. Select ECM_02 (1), then Reprogramming (2), the software variant applicable to your market will be displayed (3). Proceed to the
software download by selecting the arrow button (4).
2
3
4
1
32. Cycle the ignition (off on off on) and wait for 30 seconds.
10/08/2016
14
33. Press the stop/start button with the brake pedal depressed to start the engine and allow it to idle until fully warm.
Care Point: The Air conditioning must be switched on and the engine coolant temperature must be above 80°C before
proceeding with the camshaft adaption procedure.
34. Select ECM (5), then Actual Values (6), select the following values as per the screenshot below (7), then select the play button
to access the required data screen.
35. The inlet camshaft values should be between 1 and 4 and exhaust values should be between -9 and -12 both values will
fluctuate slightly. If all values are correct no further action is required proceed to step 37. If any values are incorrect proceed to
step 36 to carry out the camshaft adaption.
6
7
5
10/08/2016
15
36. Switch the engine off, wait 30 seconds, restart the engine and recheck the values. Repeat this procedure until the target values
are achieved.
Care point: The fuel level must be above 1/4 before you proceed to the Diagnostic Module Leakage Test (DMTL).
Care point: The DMTL test can take up to eight minutes to complete the 20 thou and 40 thou leak test
37. Select Sequences (8), then DMTL Diagnostic Module Leakage Test (9), followed by the arrow button to proceed (10).
8
10
9
38. End the current MDS session to allow session feedback to be sent and stored at McLaren.
10/08/2016
16
Care Point: Navigation software update only needs to be performed on vehicles that have not previously had platform 8.5
campaign completed. This can be confirmed by checking the application software level part number suffix does not end in .46.
IRIS AIS Application Software:
Care Point: The Application Software will be supplied via USB to dealers.
Care Point: Do not turn off the engine or change the ignition state during the update process unless stated within this update
procedure.
39. Switch the ignition ON to ignition state 5 and start the engine.
40. Make a note of the options displayed on the Home Screen as this information will be required to configure the head unit.
Example screen below of the home page (1).
1
41. Insert the USB drive with the application software into the USB socket (2).
2
10/08/2016
17
42. Once the USB has been inserted, the system should provide a message stating a USB device has been detected.
43. Press the Settings hard button on the IRIS console.
44. Select About (3) and then Update Product (4).
4
3
45. On the following screen select Update by USB Stick (5). A pop up message will be displayed. Press OK (6) to start the loading
operation.
5
6
10/08/2016
18
46. The following screen will be displayed (7) and the system will reboot.
7
47. After the system has rebooted it will search for and check the update file (8). Once the installation has finished the following
screen will be displayed (9) and the system will reboot.
8
10/08/2016
9
19
48. Following the reboot the system will start to update the individual system components (10), (11). During the update the
system may reboot multiple times. This is normal, do not attempt a manual reset.
11
10
Care Point: In case the system should get stuck on the update screen if one of the component updates has failed, press and hold
the home button for 45s to force the system to reboot.
49. Once all components have been updated and the system has fully rebooted, press the Settings hard button on the IRIS
console.
50. Select About (12) and then select Versions (13).
13
12
10/08/2016
20
51. Confirm that the McLaren
Software Part Number matches the Part Number listed in Table at Page 2 of this document.
52. Press the Home button on the IRIS console to return to the Home screen and remove the USB drive.
Care Point: For vehicles where the Learn Vehicle Model process has been completed previously the option will not be available on
the Home screen. In this case go to step 54.
53. Select Learn Vehicle Model (14) from the Home Screen. The system will perform a configuration update and reboot. Wait until
the system has fully booted to the Home screen before proceeding to the next step.
14
Care Point: The VCI must be connected to the MDS with the USB cable to perform the next steps.
54. Start a new MDS session in the MDS Offline mode, refer to Service Information Bulletin 11 S 011 McLaren Diagnostic System
(MDS) Offline, and proceed to complete the remaining procedures.
55. Select HU_02 (15), then select Sequences (16), select Align Vehicle Configuration (17), followed by the arrow key (18).
56. Select Programme VIN (19), followed by the arrow key (18).
16
18
17
19
15
10/08/2016
21
57. Select Head Unit Configuration (20), followed by the arrow key (21).
21
20
58. The following screen will appear, select OK ( 22).
22
10/08/2016
22
59. Select the relevant country followed by OK (23).
23
Care Point: The following screen will appear only if Canada is selected above. For any other countries proceed to step 61.
60. Select the relevant radio frequency option, followed by OK (24).
24
10/08/2016
23
61. Is rear view camera fitted, select Yes or No (25).
25
Care Point: McLaren Track Telemetry is not available option for McLaren 650S and 625C.
63. Proceed and select No (26).
26
10/08/2016
24
64. Operation successful will be displayed. Select the back arrow (28) to exit the sequence.
27
10/08/2016
25
Care Point: Performing Factory Data Reset will delete the stored radio stations and paired phones.
65. Press the Settings hard button on the IRIS console.
66. Select Advanced Settings (28) and then Privacy (29) in order to access the Factory Data Reset.
29
28
67. Select Factory Data Reset (30) followed by Reset (31) and then Erase Everything (32).
30
32
31
68. The system will reboot. The Factory Data Reset will be completed once the system has returned to the Standby Screen.
69. Wait until the system has fully rebooted, then switch the engine off and ignition back on.
10/08/2016
26
Navigation Software Update:
Care Point: The Navigation maps have been provided via USB stick as part of a previous software update and should be reused.
Care Point: Navigation software update only needs to be performed on vehicles that have not previously had platform 8.5
campaign completed. This can be confirmed by checking the application software level part number suffix does not end in .46.
Care Point: Navigation software update needs to be performed in China/Hong Kong vehicles irrelevant to the previous application
software level installed.
Care Point: The Navigation map for China and Hong Kong has not been sent via USB drive to the dealers and has not been
installed at production. The installation and activation needs to be completed at the local dealer, please contact your regional
office for further assistance.
Care Point: The Navigation map installation is only applicable for markets with navigation support. Please refer to Table at Page 2
of this document to determine whether navigation is available for the respective market.
Care Point: Do NOT turn off the engine or change the ignition state during the update process unless stated within this update
procedure.
70. Switch the ignition ON to ignition state 5 and start the engine.
71. Insert the USB drive with the Navigation Maps into the USB socket (1).
72. Once the USB has been inserted, the system should provide a message indicating that a USB device has been detected.
1
10/08/2016
27
73. After 1-2 minutes the screen below will be displayed. Select Update (2).
74. The following screen (3) will appear when old files have been detected and need to be removed before new files are loaded.
2
3
75. The following screen (4) will be displayed, stating the number of files to be copied and the current progress. Depending on the
map region to be installed, the number of files may differ from the example below.
76. Press Done to complete the installation (5) and remove the USB drive.
5
4
77. Complete a Factory Data Reset by following steps 65-69 in the IRIS AIS Application Software Installation section.
78. Wait until the system has fully rebooted, then turn the engine and ignition off.
10/08/2016
28
IRIS Electronic User Manual Installation:
Care Point: The Electronic User Manual is only available for McLaren 650S and 625C models and is not supported on McLaren 12C
model.
79. Access the McLaren Marketing Toolkit Website https://www.mclarenmarketingsuite.com to download the required owner
manual.
80. If you are a registered user enter your Username and Password to sign in. Proceed to Step 84.
81. If you are not a registered user click at “Click here to register for access” (1) to register.
1
82. Complete the form with your details and where it asks to select “which best applies to you” select McLaren Technical (2).
2
83. Submit the form and a request will be sent to McLaren. As soon as the request has been approved you will receive an email and
you will then be able to sign in to the McLaren Marketing Toolkit Website.
84. Click on Read More (3) under Owners Manual and Installation section.
3
10/08/2016
29
85. To download Owner Manuals click at the zip file (4) required based on the market. Please refer to Table at Page 2 of this
document to determine the correct user manual versions for each market.
4
86. A File Download pop-up will appear, select Save (5) to save the file to your local hard drive.
5
Care Point: The USB drive must be formatted to FAT32 before used.
87. Extract the zip file and copy the folder named user_manual into a blank USB drive. Please note that only one user manual can
be installed at a time.
Care Point: Do not turn off the engine or change the ignition state during the update process unless stated within this update
procedure.
10/08/2016
30
88. Switch the ignition ON to ignition state 5 and start the engine.
89. Insert the USB drive with the User Manual into the USB socket (6).
6
90. Once the USB has been inserted, the system should provide a message indicating that a USB device has been detected.
91. After 1 to 2 minutes another screen will be displayed indicating “New Files Found”. Select Update (7) to erase any existing user
manual files and to install the new files.
7
10/08/2016
31
92. If any old files are detected, these files will be removed before the new files are loaded. A status bar will be displayed showing
the progress (8).
93. Once the old files have been removed, the system will start to download the new files and the progress will be displayed on the
screen (9). Please note that the number of files that have been copied may be different from the example below.
8
9
94. Press DONE to complete the installation (10) and remove the USB drive.
95. Complete a Factory Data Reset by following steps 65-69 in the IRIS AIS Application Software Installation section.
96. Wait until the system has fully rebooted, then turn the engine off and ignition back on.
97. The user manual can be accessed via the Apps menu. Press the Apps Icon on the Home screen then select User Manual (11) to
confirm that the User Manual has been correctly installed.
11
10
10/08/2016
32
Adaptions Requirements:
98. Select ECM (1), then Sequences (2), then Clear Misfire adaptations (3), followed by the arrow button (4) to proceed.
2
4
1
3
99. Select Actual Values (5), select the following values as per the screenshot below (6), then select the play button to access the
required data screen.
5
6
10/08/2016
33
100. Misfire adaptations are performed whilst the car is driven with the gearbox set to manual mode and with the A/C off.
Perform eleven successive fuel cuts from above 4000rpm for a 5 second duration (a fuel cut off will occur when the accelerator
pedal is fully released).
101. Once the Fuel off Adaption Counter reaches 11, the Fuel off Adaption Finished Counter will display 1; the misfire adaptions
have been learned. The Fuel off Adaption Counter will display Zero and then start to count again when further fuel cut offs occur,
this is correct operation and no further action is required.
Please contact your Regional Aftersales Manager should you have any questions relating to the information contained in this
bulletin.
10/08/2016
34
Warranty Information: An additional time of 0.25 hours to update the Navigation software (if required) can only be claimed in
the Additional Costs section of the warranty claim.
WARRANTY INFORMATION
DESCRIPTION
RESOLUTION CODE
TOTAL REPAIR TIME
Software Platform Update to 9.5
M0M30110A33I4A07
2.2hours
PARTS INFORMATION
DESCRIPTION
PART NUMBER
QUANTITY
ORDER PROCESS
N/A
N/A
N/A
N/A
10/08/2016
35
If the PDF is very large, it may not load in the preview below.
Some older TSBs had multiple PDFs — visit the NHTSA Website to view all PDFs.
If the TSB PDF does not show, download or view it on the NHTSA Website.
Click on the (+) Plus Sign
Then Click on Associated Document(s)
Search NHTSA Database for Recalls
Search NHTSA Database for Vehicle Investigations
View Latest Vehicle Investigations
Search NHTSA Database for Vehicle Complaints
View Latest Vehicle Complaints
TSB/Document ID: SCB 11 M 090
Replacement Service Bulletin Number:
MFR Communication Date: 2016-08-10
MFR Internal Campaign ID/Software Version:
Communication Type: Service Bulletin/Repair Instructions
NHTSA Components: ENGINE AND ENGINE COOLING
MFR Component System:
MFR Component Subsystem:
Previous TSB | Next TSB |
- [Notice] When you receive a used device, it may be a customer return resold by Amazon without inspection. You can exchange it for a new one through Amazon. As this situation is unavoidable, we sincerely apologize. For any issues, contacting us via Amazon's "Messages" is the best way. THINKSCAN 689BT Bidirectional Scan Tool Can Be Used Immediately After It is Turned On, Without Complicated Registration Process, Which is More Convenient & Quick.
- Full Bi-Directional Control & 3000+ Active Tests: Take control and test components like actuators, fuel injectors, relays, and cooling fans in real time. You’ll quickly see if the problem is in the part itself or the control module — saving you hours of guesswork and frustrating trial-and-error.
- Advanced ECU Coding Capabilities: Handle module matching and hidden feature activation with confidence. When you replace an ECU or want to customize settings, this obd2 scanner diagnostic bi directional tool gives you the professional-level capabilities you need without the dealership price tag.
- 34+ Useful Reset and Maintenance Functions: Complete everyday service tasks smoothly with a wide range of helpful reset and maintenance functions. Whether you’re keeping up with regular upkeep or tackling a specific job, this scanner makes maintenance simpler and less stressful for both DIYers and pros.
- Comprehensive Full System Diagnostics: Diagnose every major system — Engine, Transmission, ABS, SRS, TPMS, and more — all in one place. Finally stop wondering if you’re missing something important; get the full picture and clear codes with ease.
- Top Reasons to Choose the D7S OBD2 Scanner: XTOOL D7S car scan tool, an upgrade of XTOOL D7, offers comprehensive features for automotive technicians, workshops, and DIY enthusiasts 1. Upgraded Hardware: 2+64GB memory, rear camera, intuitive interface, foldable bracket 2. Complete Diagnostics: FCA
Autoauth, OE-level all system scan, 39+ maintenance services, 4K+ bidirectional, CANFD/DoIP protocol 3. Advanced Capabilities: ECU c0ding, PMI functions 4. Wide Compatibility: Support 10,000+ models, covering 99% vehicle brands 5. Multi-language: Available in 22+ languages, No IP Restrictions 6. 3-Year Updates: Save 300 bucks on software updates for the latest features and optimizations - 2026 Upgraded D7S Car Scanner Features: The newly 2026 D7S V2.0 scanner for car brings exciting features for advanced vehicle diagnostics and enhanced user experience 1. FCA AutoAuth: Now supports FCA SGW module for Chrysler, for Jeep, for Dodge (2018+), for Fiat (2017+), enabling faster vehicle communication without gateway restrictions 2. PMI (Offline ECU Pr0gramming): Allows for Ford, for Lincoln, and for Mazda ECU pr0gramming for new modules 3. Optimized Diagnostic Report 2.0: Personalized reports with logos and customer info for auto shops. Note: Compatibility varies by cars, please check before order
- 39+ Services/Resets/Adaptations/Relearns/Calibrations: XTOOL D7S full system car scanner diagnostic tool tackles 99% of common car issues through its 36+ special functions, including Oil Reset, EPB, SAS, BMS, Throttle Reset, Injector C0ding, ABS Bleed, TPMS Reset, Power Balance, etc and also covers specific-vehicle functions like Crank Sensor Relearn, ABS Initialization, Cylinder Power Balance, Fuel Trim Reset, Idle Relearn etc. This car diagnostic scanner enhances efficiency, making repairs and maintenance hassle-free. Tip: DO NOT for All vehicles, please check compatibility first
- Cost-effective ECU C0ding Scan Tool for Specific Brands: Enhance your vehicle's performance with XTOOL D7S! This obd2 scanner all systems bidirectional offers advanced capabilities at an affordable price, supports online for BMW, for Benz and offline for BENZ, for MIT, along with PMI functions for Ford, for Mazda, and for Lincoln. Ideal for technicians and DIY enthusiasts, this automotive scanner diagnostic tool optimizes vehicle performance and enhances the driving experience. Note: Not for all cars and modules, please send car VIN to check the compatibility before purchase
- OE All System Diagnostic & 8 Pids Graphing: XTOOL D7S is a comprehensive all system bi directional obd2 scanner that delivers dealer-level diagnostics, completely controlling over your vehicle’s performance and health. This automotive scan tool can read and clear DTCs, view live data and ECU information, retrieve freeze frames, and perform active tests and full obd2 functions. This bi-directional scan tool can can identify your vehicle's make, model, and year information with just one click and show up to 8 PIDs live data with options for CSV viewing, playback, and recording for in-depth analysis. It is easy-to-use for both professionals and beginners, helping pinpoint issues efficiently
- 【✅Compared to BOSSCOMM IF742, IF745 Offers Full-System Diagnostics】The BOSSCOMM IF745 car diagnostic scanner is an upgraded model of IF742. In addition to supporting all OBD2 Code Reader functions and 6 reset options (ABS/EPB/SAS/BMS/Oil/Throttle), it expands diagnostics from 4 systems (Check Engine/ABS/SRS/Transmission) to vehicle All systems, including Steering, Suspension, and Body Electronics. This provides deeper, more comprehensive diagnostic capabilities.
- 【✨10 OBD2 Functions】The BOSSCOMM IF745 scan tool’s DTC Lookup instantly translates fault codes into user-friendly explanations, its I/M Readiness feature streamlines emissions testing with a single tap, and Freeze Frame lets you pinpoint the exact moment of a fault for in-depth root-cause diagnosis. Combined with a live data dashboard and advanced diagnostics (O2S, OBMon, EVAP), it delivers comprehensive insights for confident troubleshooting.
- 【✨Deep Diagnostics for All Vehicle System Modules】Beyond code reading/clearing and ECU information retrieval, our all-in-one data stream feature lets you inspect all current fault codes and their locations across the vehicle’s systems. This vehicle code reader helps you turn off dashboard warning lights and perform a comprehensive self-check of your car at home—no more back-and-forth trips to the repair shop or hefty inspection fees.
- 【✨6 Essential Resets: ABS Bleeding, Oil, EPB, SAS, Throttle, BMS】The BOSSCOMM IF745 obd2 scanner diagnostic tool swiftly purges air from brake lines to restore braking sensitivity, fine-tunes maintenance cycles to eliminate false alerts, resolves parking brake issues with one-click control, recalibrates steering sensors for stability, optimizes engine idling/acceleration for smoother performance, and deeply resets battery systems to extend lifespan and range via precise parameter adjustments.❗NOTE: Does NOT support bidirectional control, coding, or programming.
- 【✨10,000+ Car Models, AutoVIN, 13 Languages】The BOSSCOMM IF745 vehicle scanner diagnostic tool covers 73+ global car brands and offers support in 13 languages, making it perfect for DIYers, auto mechanics, or as a thoughtful gift. With a single-click AutoVIN feature, it instantly retrieves vehicle serial numbers, streamlining diagnostics for users globally. This adaptable tool balances user-friendliness with precision, catering to both personal and professional requirements.✅Unsure about compatibility? Compatibility will vary on vehicles' model and year, pls reach us via 📧 [email protected] 📧 before purchase.
This product presentation was made with AAWP plugin.