8/3/2020

Content creation stages KC-2033

Volvo Chassis - Bendix ABS Fault SPN 807 FMI 13
Blink code 19-4




Volvo Trucks without HSA (Hill Start Assist)
Remove the mushroom vent from ATR6 valve control port and run 3/8 line from
the valve to open port in manifold mounted on the dash panel.

Related links and
attachments
No content available

Air Line Fitting P/N Reference
Fitting Size
P/N
1/8 - 27 NTF X 3/8
8397698
1/4 -18 NTF X 3/8
8397700

Program ABS controller
"Con guration” operation found in Tech Tool. The operation will
download a con guration le for the connected vehicle and initiate
con guration of the ESP feature via the Bendix®
Vendor Con guration Program (VCP).
A speci c Bendix® VCP package for Tech Tool must be installed on the
PC prior to performing an ESP con guration. This software is not
installed as part of Tech Tool and therefore must be downloaded and
installed separately.
The Bendix® VCP installation can be found on the Trucks Dealer Portal
website.
NOTE - This installation le may be updated at any time and should be
downloaded only from the Trucks Dealer Portal website.
Download Instructions:
1. Login to Trucks Dealer Portal (TDP)

https://volvo-trkna-prod1.pegacloud.net/prweb/PRAuth/iNPUIKpeinqPJi2G0hH930k43USdE1gb*/!TABTHREAD7?pyActivity=%40baseclass.pzProcess…

1/8

8/3/2020

Content creation stages KC-2033

2. Under the UPTIME tab select the Software Downloads option or
click here

3. Select Bendix VCP link to download the latest installation

https://volvo-trkna-prod1.pegacloud.net/prweb/PRAuth/iNPUIKpeinqPJi2G0hH930k43USdE1gb*/!TABTHREAD7?pyActivity=%40baseclass.pzProcess…

2/8

8/3/2020

Content creation stages KC-2033

4. Save the .zip le in a location on the PC that is easy to nd - for
example, "C:\Temp" or the Desktop.
Software Installation:
CAUTION: If the Bendix® Vendor Con guration Program or ABS6
Vendor Con guratio Program is already installed on PC - it must be
removed prior to installing a new version.
Removal Instructions:
1. Go to the ‘Control Panel’ in Windows – double click on ‘Add or Remove
Programs’.
2. In the list of currently-installed programs nd Bendix® ABS6 Vendor
Con guration Program or Bendix® vendor con guration Program right click and select 'Remove/Uninstall'
3. Follow the prompts guiding you through the uninstall process.- Once
the old version has been removed – the new version can be installed.
Bendix (VCP) Installation:
1. Go to the location where the .zip was saved
2. Open the zip le and double - click the BendixSoftware.exe le.
https://volvo-trkna-prod1.pegacloud.net/prweb/PRAuth/iNPUIKpeinqPJi2G0hH930k43USdE1gb*/!TABTHREAD7?pyActivity=%40baseclass.pzProcess…

3/8

8/3/2020

Content creation stages KC-2033

Note: It may be necessary to extract the le to a temporary location
before running the .exe le.
1. Right lick on the .zip le and "extract" it to a temporary location.
2. Go to the temp location, nd the Bendix Vendor Con guration
Program VM.exe le and double- click it.
3. Follow the installation instructions used in the default settings.
(Additional components used by Bendix® VCP will be installed if they are
not on the PC)
Note: A message will be shown if an additional required component is
not installed on the PC. [see gure 2]

Figure 2
1. Click ‘Install’ to install the component; selecting ‘Cancel’ will abort the
installation.
2. When the component installation nishes, the installation will
continue. Click ‘Next’ to proceed. [see gure 3]

https://volvo-trkna-prod1.pegacloud.net/prweb/PRAuth/iNPUIKpeinqPJi2G0hH930k43USdE1gb*/!TABTHREAD7?pyActivity=%40baseclass.pzProcess…

4/8

8/3/2020

Content creation stages KC-2033

Figure 3
Network Connection at the Vehicle
In order to perform the ESP Control Unit Con guration operation, it must
be possible to connect to the vehicle and
the Central Systems at the same time. Therefore, it must be possible for
the PC to have a network (LAN or Wi-Fi) connection while also connected
to the vehicle’s diagnostic connector.
Performing ESP Control Unit Con guration
After performing the actions outlined in the Preparation section above,
connect the PC to the vehicle’s diagnostic connector and complete the
vehicle identi cation process displayed in Tech Tool’s ‘PRODUCT’ tab.
(Make sure that the PC has the possibility to connect to Central Systems
via a network/internet connection).Select the “Calibrate” tab and expand
group ‘5 – Brakes’ and open the ‘ESP Control Unit
Con guration’ operation. [see gure 4]

https://volvo-trkna-prod1.pegacloud.net/prweb/PRAuth/iNPUIKpeinqPJi2G0hH930k43USdE1gb*/!TABTHREAD7?pyActivity=%40baseclass.pzProcess…

5/8

8/3/2020

Content creation stages KC-2033

Figure 4
The ESP Control Unit Con guration operation is structured as a checklist
of actions, similar to
control unit software programming operations. [see gure 5]

Figure 5

Start the operation by clicking the start button in the toolbar. After the
conditions are con rmed, the operation will read data from the vehicle. A
connection to Central Systems will be made in order to download the
ESP system con guration le for the connected vehicle.
After the ESP system con guration le is downloaded, a con guration
window containing a status bar will appear while the ESP control unit is
con gured. [see gure 6]

https://volvo-trkna-prod1.pegacloud.net/prweb/PRAuth/iNPUIKpeinqPJi2G0hH930k43USdE1gb*/!TABTHREAD7?pyActivity=%40baseclass.pzProcess…

6/8

8/3/2020

Content creation stages KC-2033

Note: On some occasions, the status bar window may appear blank.
Although it appears that no action is occurring, the process is
proceeding. In this case, allow the process to continue. The ABS ECU will
be restarted and the con guration window will disappear when its task is
complete and the process will continue in the main operation window.

Figure 6
After the con guration is complete, the con guration window will
be closed and another connection to Central Systems will be made
in order to send a con rmation that the con guration has
been completed successfully.
Once the con guration has been completed verify that the sysyem air is
fully charged. Apply ignition power and wait 30 seconds. Perform a full
application of service brake and hold for 5 seconds. Release the service
brake. Check for fault codes with ACOM.

a

Tags

19-4

VCP

SPN 807 FMI 13

https://volvo-trkna-prod1.pegacloud.net/prweb/PRAuth/iNPUIKpeinqPJi2G0hH930k43USdE1gb*/!TABTHREAD7?pyActivity=%40baseclass.pzProcess…

7/8

8/3/2020

Content creation stages KC-2033

Feedback
Give feedback to help improve the content of this article

https://volvo-trkna-prod1.pegacloud.net/prweb/PRAuth/iNPUIKpeinqPJi2G0hH930k43USdE1gb*/!TABTHREAD7?pyActivity=%40baseclass.pzProcess…

8/8