The ’Choose Components’ window appears next. All of the components are automatically selected. If there
are components you do not want to install, remove the check mark beside the component(s) and select
’Next’ as shown in Fig. 11.

15.

A window will open to choose the install location. Allow it to install in the default directory or the application
may not work correctly. Select ’Install.’ See Fig. 12.

05/06/2020

f120744

Fig. 11, Choose Components Window

05/06/2020

Fig. 12, Choose Install Location Window

16.

A bar shows the progress of the Kvaser installation. See Fig. 13.

17.

A window will appear when the installation is complete. Select ’Close.’ See Fig. 14.

05/06/2020

Fig. 13, Kvaser Installation Progress Bar

Page 7

f120745

f120746

05/06/2020

f120747

Fig. 14, Kvaser Installation Complete Window

Daimler Trucks
North America LLC

Field Service Campaign

June 2020
SF606

18.

Go back to www.DTNAConnect.com and select ’Support,’ then select ’Download Center.’ See Fig. 1 ref. B
and ref. C. Select ’8.0L LPG Engine Calibration Update’ then select the engine calibration link, shown in
Fig. 15.
Select the down arrow beside save. See Fig. 16.

05/05/2020

f120719

Fig. 15, Engine Calibration Link

05/07/2020

f120720

Fig. 16, Calibration Save Window

19.

Choose ’Save As’ from the drop-down list shown in Fig. 17.

05/06/2020

f120748

Fig. 17, Choosing Save As

20.

Browse through the directory where the Agility service link calibration folder was installed earlier
[C:\AgilityServiceLink] and double click the Agility Service Link folder. See Fig. 18.

07/06/2020

f120788

Fig. 18, Directory Window
Page 8

Daimler Trucks
North America LLC

Field Service Campaign

June 2020
SF606

21.

Once the folder is open, save the calibration program in the RPG folder. See Fig. 19.

07/06/2020

f120789

Fig. 19, Saving the Calibration in the RPG Folder

Page 9

Daimler Trucks
North America LLC

Field Service Campaign

June 2020
SF606

Opening Agility Service Link
IMPORTANT: If the raptor screen, shown in Fig. 20 appears, do not run the application. Close and then right
click on the application icon and select ’Run as administrator.’ See Fig. 21. The technician may need help from
their IT department to use administrator rights.
1.

Double click the Agility icon on the desktop. See Fig. 22.

07/06/2020

f120790

Do not run the application if this screen appears.
Close and then right click on the application icon
and select ’Run as administrator.’
Fig. 20, Raptor Screen

05/05/2020

f120729

Fig. 22, Agility Icon on the Desktop

07/06/2020

Fig. 21, Selecting Run as Administrator

Page 10

f120792

Daimler Trucks
North America LLC

Field Service Campaign

June 2020
SF606

2.

When the Agility tool opens, select ’Help,’ and then select ’License Viewer.’ See Fig. 23.

05/05/2020

f120730

Fig. 23, Help Window

Page 11

Daimler Trucks
North America LLC

Field Service Campaign

June 2020
SF606

NOTE: A unique machine code was automatically created when the program was installed. Write down the machine code for the next step. You will have to provide this code when contacting agility. See Fig. 24.
3.

The ’License Viewer’ window will open. See Fig. 24. You will need to contact Agility at 1-949-207-5364
between 8 A.M. to 5 P.M. eastern standard time and provide the machine code noted earlier, and then ask
for the license code. Any phone call after this time will go to voicemail.

IMPORTANT: Agility will charge a fee for each license code. The code can only be used for one vehicle identification number (VIN). Technicians should have a credit card or purchase order available when they call Agility.
4.

Once the license code is created by Agility, enter it in the ’Apply a New License Code’ section shown in
Fig. 24, then select ’Apply’ and close the window.

05/05/2020

f120731

Fig. 24, Raptor-Service License Viewer Window

Interface Selection
IMPORTANT: Ensure that the Nexiq box (or other communication interface) has a solid green lamp. This indicates that the communication interface will detect the program information.
1.

Connect an RP1210B compliant vehicle diagnostic adaptor to the laptop and the vehicle diagnostic port.

2.

Open the Agility service tool.

Page 12

Daimler Trucks
North America LLC

Field Service Campaign

June 2020
SF606

3.

Right click the ’Virtual 1(250k)’ box, then select ’CAN Settings.’ See Fig. 25.

4.

Select ’RP1210’ or ’Kvaser’ from the ’Driver’ options as applicable, shown in Fig. 25.

NOTE: The user may have to restart the Agility service tool to ensure that the changes made were saved.
5.

Select the ’Channels’ drop-down list, then select the interface being used and select ’Save.’ See Fig. 25.

05/07/2020

f120732

Fig. 25, Virtual 1(250k) Window

Programming Software or Calibration
IMPORTANT: Never perform the calibration with a vehicle battery that has a low charge or a battery charger
that is set too high.
1.

Connect a battery charger to the vehicle battery.

2.

Turn the ignition to the RUN position.

Page 13

Daimler Trucks
North America LLC

Field Service Campaign

June 2020
SF606

3.

Select ’Find Modules’; all of the available modules appear in the window. See Fig. 26.

05/05/2020

f120721

Fig. 26, Find Modules Window

4.

Write down the ’Software ID and Calibration ID’ (near the ECU image). See Fig. 26.

Page 14

Daimler Trucks
North America LLC

Field Service Campaign

June 2020
SF606

5.

Select ’Flash,’ then double click the module you want to flash (it has the ECU image beside it). See
Fig. 27.

05/05/2020

f120722

Fig. 27, Selecting Flash and the Module to be Flashed

6.

A browse window will open in the bottom left of the screen. Select AgilityEC_234006007_P1.rpg, then select ’Open.’ This will begin the calibration programming.

7.

The instrument panel will produce a chime, indicating that the ECU is reprogramming.

Page 15

Daimler Trucks
North America LLC

Field Service Campaign

June 2020
SF606

8.

A bar shows the progress of the ECU as it is reprogrammed. See Fig. 28.

IMPORTANT: The ignition must be turned off for a minimum of 15 seconds in order for the update to take effect.
9.

Turn the ignition off for a minimum of 15 seconds.

10.

The ’Persisted Values Have Been Restored’ window appears. Select ’OK’. See Fig. 29.

05/05/2020

f120724

Fig. 29, Persisted Values Have Been Restored Window

05/05/2020

f120723

Fig. 28, Progress Bar Window

11.

The ’Programming Successful’ window will appear. Select ’OK.’ See Fig. 30.

05/05/2020

f120725

Fig. 30, Programming Successful Window

IMPORTANT: The ignition must be turned off for a minimum of 15 seconds in order for the update to take effect.
12.

When programming is complete, turn the ignition to the OFF position for a minimum of 15 seconds and
then back to the RUN position.

13.

Clean a spot on the base label (Form WAR259) and attach a campaign completion sticker for SF606
(Form WAR261) indicating this work has been completed.

Page 16