Revised June 2020
Dealer Service Instructions for:

Emissions Recall V86
Catalytic Converter Efficiency
NOTE: The Subject has been revised.

Remedy Available
2015-2017 (LA) Dodge Challenger Hellcat
2015-2017 (LD) Dodge Charger Hellcat
NOTE: This recall applies only to the above vehicles equipped with a 6.2L
supercharged engine (sales code ESD).
NOTE: Some vehicles within the above build period may have been identified as
not involved in this recall and therefore have been excluded from this recall.
IMPORTANT: Some of the involved vehicles may be in Dealer vehicle
inventory. Dealers should complete this recall service on these vehicles before
retail delivery. Involved vehicles can be determined by using the VIP inquiry
process.

Subject
Degradation of the catalytic converter on about 25,180 of the above vehicles may
result in those vehicles exceeding the emissions standards for Non-Methane
Organic Gas (NMOG) and Nitrogen Oxide (NOx).

 Copyright 2020, FCA US LLC, All Rights Reserved

(tdb)

Emissions Recall V86 -- Catalytic Converter Efficiency

Page 2

Repair
Update the Powertrain Control Module (PCM) with the latest available software.
Replace the catalytic converters and the oxygen sensors.

Parts Information
Part Number

Description

CEAHV861AA

Catalyst - Right Side

Each package contains the following components:
Quantity
1

Description
Catalyst - Right Side

Part Number

Description

CEAHV862AA

Catalyst - Left Side

Each package contains the following components:
Quantity
1

Description
Catalyst - Left Side

Part Number

Description

CEAHV863AA

Campaign Kit - Parts Package

Each package contains the following components:
Quantity
4
4
1
1
2

Description
Catalyst Nut - 2 per catalyst
Double Ended Stud - 2 per catalyst
O2 sensor – Left Side Upstream
O2 sensor – Right Side Upstream
O2 sensor – Left Side/Right Side Downstream

Emissions Recall V86 -- Catalytic Converter Efficiency

Page 3

Parts Information [Continued]
Part Number

04275086AE – Authorized Modification Label
Ordering Additional Authorized Modification labels:
The labels may be ordered using the Marketing Materials link within
DealerCONNECT.
Process Steps to Order Additional labels and extended warranty information
kits:
1. Access the “DealerCONNECT” website.
2. Select the “Marketing” link in the header of DealerCONNECT.
3. Locate the “Product Information” section heading on the Marketing page.
4. Select the “Literature and Merchandising Materials” link in the product
information section.
5. Locate the “MOPAR” section heading on the Literature and Merchandising
Materials page.
6. Select the “Recall Labels / Cards” link listed in the MOPAR section.
7. Select Item > Update Cart > Submit Order.

Parts Return
Return the Catalyst to the Mopar Core Return Center for core credit.
Refer to Section E under Service Procedure for proper Core Return preparation.

Emissions Recall V86 -- Catalytic Converter Efficiency

Special Tools
The following special tools are required to perform this repair:
 NPN

wiTECH micro pod II

 NPN

Laptop Computer

 NPN

wiTECH Software

Page 4

Emissions Recall V86 -- Catalytic Converter Efficiency

Page 5

Service Procedure
A. Reprogram the ECM with the Latest Available Software
NOTE: The wiTECH scan tool must be used to perform this recall. If the
reprogramming flash for the PCM is aborted or interrupted, repeat the
procedure.
CAUTION: the PCM software must be at the latest software calibration
level after completing this recall.
1. Open the hood and install a battery charger. Verify that the charging rate
provides 13.0 to 13.5 volts. Do not allow the charger to time out during the
flash process. Set the battery charger timer (if so equipped) to continuous
charge.
NOTE: Use an accurate stand-alone voltmeter. The battery charger volt
meter may not be sufficiently accurate. Voltages outside of the specified
range will cause an unsuccessful flash. If voltage reading is too high, apply
an electrical load by activating the park or headlamps and/or HVAC
blower motor to lower the voltage.
2. Connect the wiTECH micro pod II to the vehicle data link connector.
3. Place the ignition in the “RUN” position.
4. Open the wiTECH 2.0 website.
5. Enter your “User id” and “Password” and your “Dealer Code”, then select
“Sign In” at the bottom of the screen. Click “Accept”.
6. From the “Vehicle Selection” screen, select the vehicle to be updated.
7. From the “Action Items” screen, select the “Topology” tab.

Emissions Recall V86 -- Catalytic Converter Efficiency

Page 6

Service Procedure [Continued]
8. From the “Topology” tab, select the “PCM” module icon.
9. From the “Flash” tab, compare the “Current Electronic Control Unit (ECU)
Part Number” with the “New ECU Part Number” listed.
 If the “Current ECU part Number” is the same as the “New Part
Number”, proceed to Step 15.
 If the “Current ECU part Number” is NOT the same as the “New Part
Number”, continue with Step 10.
10. From the PCM tab, select the PCM flash part number. Read the flash special
instructions page. Select “OK” to continue.
NOTE: 2015 model year vehicles only will receive updated software for the
TCM while flashing the TCM as a combined flash. It will not be necessary
to flash the TCM separately, follow the screen instructions to complete the
flash.
11. From the flash ECU agreement page, agree to terms by checking the box.
12. Select “Flash ECU” and then follow the wiTECH screen instructions to
complete the flash.
13. Confirm the software is at the latest available calibration level.
14. Click “View DTCs”, select “Clear All DTCs”, click “Continue” and then
click “Close”.
15. Place the ignition in the “OFF” position and then remove the wiTECH micro
pod II device from the vehicle.
16. Remove the battery charger from the vehicle.
17. Proceed to Section B. Replace Catalytic Converters.

Emissions Recall V86 -- Catalytic Converter Efficiency

Page 7

Service Procedure [Continued]
B. Replace Catalytic Converters
1. Make sure ignition switch is in “OFF” position and all accessories are turned
OFF.
2. Remove the rear compartment floor, trim panel to gain access to the battery.

3. Loosen the M6 captive nut (1)
securing the battery negative
cable clamp to the battery
negative post (Figure 1).
NOTE: Do not remove the
M6 captive nut, doing so will
cause the M6 stud on IBS
pole clamp to break.

Figure 1 – Battery Negative Terminal Nut

4. Disconnect the Intelligent
Battery Sensor (IBS) electrical
connector (1) (Figure 2).

Figure 2 – IBS Electrical Connector

Emissions Recall V86 -- Catalytic Converter Efficiency

Page 8

Service Procedure [Continued]
5. Remove the M8 hex nut (1)
securing the battery negative
cable eyelet to the IBS
(Figure 3).

Figure 3 – Negative Cable Eyelet Nut

6. Remove the battery negative
cable eyelet (2) from the IBS
M8 stud (Figure 4).

Figure 4 – Negative Cable Eyelet

7. Raise and support the vehicle.

Emissions Recall V86 -- Catalytic Converter Efficiency

Page 9

Service Procedure [Continued]
8. Saturate all exhaust bolts and nuts with Mopar® Rust Penetrant. Allow five
minutes for penetration.
WARNING: The normal operating temperature of the exhaust system is
very high. Therefore, never attempt to service any part of the exhaust
system until it is cooled. Special care should be taken when working near
the catalytic converter. The temperature of the converter rises to a high
level after a short period of engine operation time.
CAUTION:
When
disconnecting the oxygen
sensor electrical connector,
do not pull directly on the
wire going into the sensor.
The sensor wiring can be
damaged resulting in sensor
failure.
9. Disconnect the oxygen sensor
wire harness connector (1) and
remove the harness from the
retainer (2) (Figure 5).

Figure 5 – Oxygen Sensors

10. Remove the oxygen sensor (3)
from the exhaust manifold
(Figure 5).

11. Disconnect the oxygen sensor
wire harness connector (2) and
remove the harness from the
retainer (Figure 6).

Figure 6 – Oxygen Sensors

Emissions Recall V86 -- Catalytic Converter Efficiency

Service Procedure [Continued]
12. Remove the catalytic converter
to manifold flange nuts (2) and
separate
the
catalytic
converters (1) from the
exhaust manifolds (Figure 7).

Figure 7 – Flange Nuts

13. Loosen the front exhaust pipe
to muffler and resonator
assembly band clamps (1)
(Figure 8).

Figure 8 – Band Clamps

Page 10

Emissions Recall V86 -- Catalytic Converter Efficiency

Page 11

Service Procedure [Continued]
14. Separate the muffler and
resonator assembly from the
catalytic converters.

15. Remove the left (1) and/or
right (2) catalytic converters
(Figure 9).

16. Position the left (1) and/or
right (2) catalytic converter
onto the exhaust manifold
flange, and install the flange
nuts finger tight (Figure 9).

Figure 9 – Catalytic Converters

17. Insert the muffler and resonator assembly onto the front exhaust pipe, without
tightening the band clamps (1) at this time (Figure 8).
18. Tighten the catalytic converter (1) to exhaust manifold flange nuts (2) to
30 N·m (22 ft. lbs.) (Figure 7).

19. Tighten the band clamps to 50 N·m (37 ft. lbs.) (Figure 8).

NOTE: The threads of the new oxygen sensors are factory coated with
anti-seize compound to aid in removal. Do not add any additional anti-seize
compound to threads of a new oxygen sensor.
20. Install the oxygen sensor (3) into the exhaust manifold and tighten to 52 N·m
(38 ft. lbs.) (Figure 5).

21. Connect the oxygen sensor wire harness connector (1) and secure the wire
harness in the retainer (2) (Figure 5).

Emissions Recall V86 -- Catalytic Converter Efficiency

Page 12