Release Date

Technical Service Bulletin

05/29/2020

97EF UPDATE
Vehicle Electrical System Module Software Update – (NVLW)

Applicable Vehicles

Country

Beginning Model Year

Ending Model Year

Vehicle

Vehicle Count

USA
CAN

2020
2020

2020
2020

A8
A8

165
14

Revision History
Revision

Date

Purpose

1

05/29/2020

Original publication

Technical Background
This Update has been proactively released to prevent the following condition(s) from occurring in the vehicle:
Criteria
H1

Technical Background
A rear light animation feature may be missing

Remedy
Criteria
H1

Remedy
Update Vehicle Electrical System Control Module (BCM/J519) software

This Update is in effect until removed.
Vehicle must meet all of the following criteria:
 Procedure is valid only for vehicles that show the 97EF code in the Elsa Campaign/Action Information screen
on the day of repair.
 Vehicle must be within the New Vehicle Limited Warranty.
 Procedure must be performed within the allotted time frame stated in this Technical Service Bulletin.
 Procedure must be performed on applicable vehicles in dealer inventory prior to sale.

The repair information in this document is intended for use only by skilled technicians who have the proper tools, equipment and training to correctly and safely maintain your vehicle. These
procedures are not intended to be attempted by “do-it-yourselfers,” and you should not assume this document applies to your vehicle, or that your vehicle has the condition described. To
determine whether this information applies, contact an authorized Audi dealer. 2020 Audi of America, Inc and Audi Canada All Rights Reserved.
May 2020

97EF Page 1 of 9

Release Date

05/29/2020

Technical Service Bulletin

97EF UPDATE
Vehicle Electrical System Module Software Update – (NVLW)

Service
NOTE:


Elsa is the only valid inquiry/verification source. Check Elsa on the day this vehicle UPDATE will be
performed to verify vehicle eligibility for the UPDATE. Status must show “open”. Attach an Elsa printout
showing the “open” status to the repair order.



If this UPDATE appears to have already been performed but the code still shows open in Elsa, contact
Warranty before proceeding further. Another dealer may have recently performed this UPDATE but not
yet entered a claim for it in the system.



Elsa may also show additional open action(s); if so, inform your customer - this work can be done while
the vehicle is in for this UPDATE.



Contact the Warranty Helpline (U.S.) or the Warranty Campaign Specialist (Canada) if you have any
questions.



Enter the VIN in Elsa and proceed to the
“Campaign/Action” screen.

TIP
On the date of repair, print this screen and keep a
copy with the repair order.


Confirm the Campaign/Action is open . If the status is closed, no further work is
required.



Note the Applicable Criteria ID for
use in determining the correct work to be done
and corresponding parts associated.
CRITICAL REPAIR STEP

STOP!
If multiple software update Campaign/Actions are
open, they must be performed in order of the Start
date . The oldest should be performed
first.


All Safety Recalls must be completed prior
to completing this campaign.

The repair information in this document is intended for use only by skilled technicians who have the proper tools, equipment and training to correctly and safely maintain your vehicle. These
procedures are not intended to be attempted by “do-it-yourselfers,” and you should not assume this document applies to your vehicle, or that your vehicle has the condition described. To
determine whether this information applies, contact an authorized Audi dealer. 2020 Audi of America, Inc and Audi Canada All Rights Reserved.
May 2020

97EF Page 2 of 9

Release Date

05/29/2020

Technical Service Bulletin

97EF UPDATE
Vehicle Electrical System Module Software Update – (NVLW)
SVM Update Instructions
NOTE
Prior to launching the VAS Diagnostic Tester and starting an update, ensure the following conditions are met;
The ODIS software is completely up to date.


Refer to the “Alerts” section on ServiceNet home page for the current ODIS version.

The battery charger is connected to the vehicle battery and remains connected for the duration of the
software update.


Battery voltage must remain above 12.5 volts for the duration of the software update. Failure to
do so may cause the update to fail, which could result in damage to the control module. Control
modules damaged by insufficient voltage will not be covered.

The screen saver and power saving settings are off.


Failure to do so may result in the tester entering power save mode during the software update,
which could result in damage to the control module.

The VAS Diagnostic Tester is plugged in using the supplied power adapters.


Under no circumstances should the tester be used on battery power alone during the software
update. Failure to do so may result in the tester powering off during the update, which could result
in damage to the control module.

Flash process through “Audi Flashing” not Guided Fault Finding (GFF).


DO NOT USE Guided Fault Finding (GFF) to perform this flash. Using GFF will cause the flash
to take longer. Requests for additional time will not be considered.

The VAS Diagnostics Interface MUST ONLY be connected to the tester with a USB cable.


Performing a software update using a Bluetooth or WiFi connection increases the risk of losing
connection during the update, which could result in damage to the control module.
It also greatly increases the time required to perform the update. Requests for additional time or
parts will be denied if the GFF log shows the update was performed using Bluetooth or WiFi.

The repair information in this document is intended for use only by skilled technicians who have the proper tools, equipment and training to correctly and safely maintain your vehicle. These
procedures are not intended to be attempted by “do-it-yourselfers,” and you should not assume this document applies to your vehicle, or that your vehicle has the condition described. To
determine whether this information applies, contact an authorized Audi dealer. 2020 Audi of America, Inc and Audi Canada All Rights Reserved.
May 2020

97EF Page 3 of 9

Release Date

05/29/2020

Technical Service Bulletin

97EF UPDATE
Vehicle Electrical System Module Software Update – (NVLW)
NOTE


All campaign software updates must be completed during a single, standalone ODIS Diagnostic Session.
You must fully complete this campaign and send all logs before beginning any other campaigns or
operations.



If there are any ODIS “Hot-Fix” patches installed, they must be removed from the scan tool before
beginning this operation. ODIS “Hot-Fix” patches may affect the update process.

WARNING
Radiator Fan(s) may cycle ON high speed during the Update Process! There is a serious risk that personal injury
may result if contact is made with spinning fan blades. Keep hands and all objects away from Radiator Fan(s)
during Update Process!
TIP
To Update-Programming using SVM, review and follow instructions in Technical Bulletin 2014603: Software
Version Management (SVM) Operating Instructions.
The SVM Process must be completed in its entirety so the database receives the update confirmation response.
A warranty claim may not be reimbursed if there is no confirmation response to support the claim.


Open the hood.



Open the battery cover.



Attach the GRX3000VAS Tester/Charger (or
equivalent) to the vehicle battery or
underhood charging posts.
NOTE

When connecting the charger directly to the battery,
connect the positive cable to the positive terminal of
the battery and connect the negative cable to the
grounding lug on the chassis. DO NOT connect the
ground cable directly to negative terminal of the
battery.


Switch on the hazard warning lights.

CAUTION
The procedure may cancel itself if the hazard
warning lights are not switched on. The hazard
warning lights prevent the system from switching to
bus sleep mode during the update.


Connect
the
VAS6150X/VAS6160X
Diagnostic Tester to the vehicle.



Start the ODIS program.

The repair information in this document is intended for use only by skilled technicians who have the proper tools, equipment and training to correctly and safely maintain your vehicle. These
procedures are not intended to be attempted by “do-it-yourselfers,” and you should not assume this document applies to your vehicle, or that your vehicle has the condition described. To
determine whether this information applies, contact an authorized Audi dealer. 2020 Audi of America, Inc and Audi Canada All Rights Reserved.
May 2020

97EF Page 4 of 9

Release Date

05/29/2020

Technical Service Bulletin

97EF UPDATE
Vehicle Electrical System Module Software Update – (NVLW)



Confirm that scan tool is communicating with
the diagnostic head by USB cable.
o

If the Bluetooth or WiFi symbol is
shown,
then
disconnect
the
diagnostic head from the vehicle and
reconnect the USB cable to the
diagnostic head and then reattach to
the vehicle.



From the home screen of the scan tool
highlight “Flash” .



Follow the on-screen prompts.
NOTE

Operating mode “Flash” must be used. Performing
this software update using “Diagnosis” (Guided
Fault Finding) could result in non-payment of the
claim.



Select “Starting Flashing” and follow the onscreen prompts.

The repair information in this document is intended for use only by skilled technicians who have the proper tools, equipment and training to correctly and safely maintain your vehicle. These
procedures are not intended to be attempted by “do-it-yourselfers,” and you should not assume this document applies to your vehicle, or that your vehicle has the condition described. To
determine whether this information applies, contact an authorized Audi dealer. 2020 Audi of America, Inc and Audi Canada All Rights Reserved.
May 2020

97EF Page 5 of 9

Release Date

05/29/2020

Technical Service Bulletin

97EF UPDATE
Vehicle Electrical System Module Software Update – (NVLW)



Select “No RO”.



Highlight “SVM – Code Input”.



Select “Perform test”.

The repair information in this document is intended for use only by skilled technicians who have the proper tools, equipment and training to correctly and safely maintain your vehicle. These
procedures are not intended to be attempted by “do-it-yourselfers,” and you should not assume this document applies to your vehicle, or that your vehicle has the condition described. To
determine whether this information applies, contact an authorized Audi dealer. 2020 Audi of America, Inc and Audi Canada All Rights Reserved.
May 2020

97EF Page 6 of 9

Release Date

05/29/2020

Technical Service Bulletin

97EF UPDATE
Vehicle Electrical System Module Software Update – (NVLW)
NOTE
Using Bluetooth or WiFi for this action is
PROHIBITED!
Damage caused to electronic components (e.g.
ECM, TCM, etc.) during the SVM flash process is
not covered.


Enter the corrective action code (SVM code)
as listed below.

SVM code

97EFA890


Select “Accept” .



Follow the on-screen prompts.



After receiving confirmation that the flash
completed successfully, select “Send”
to send the diagnostic protocol
online.



Follow the on-screen prompts.



Click “Flash” to exit the flash session.

TIP
Various event memory entries may be generated
after the flashing procedure on some vehicles. Put
the vehicle in a corresponding bus sleep mode
after performing the update in order to clear the
faults.
To put the vehicle in bus sleep mode, disconnect
the diagnostic tester, remove the key from the
vehicle and lock the vehicle with the remote for 5
minutes.

The repair information in this document is intended for use only by skilled technicians who have the proper tools, equipment and training to correctly and safely maintain your vehicle. These
procedures are not intended to be attempted by “do-it-yourselfers,” and you should not assume this document applies to your vehicle, or that your vehicle has the condition described. To
determine whether this information applies, contact an authorized Audi dealer. 2020 Audi of America, Inc and Audi Canada All Rights Reserved.
May 2020

97EF Page 7 of 9

Release Date

Technical Service Bulletin

05/29/2020

97EF UPDATE
Vehicle Electrical System Module Software Update – (NVLW)

Warranty
Claim Entry Instructions
After Update has been completed, enter claim as soon as possible to help prevent work from being duplicated
elsewhere. Attach the Elsa screen print showing action open on the day of repair to the repair order.
If customer refused campaign work or vehicle is out of the specified warranty parameter for this Update:


U.S. dealers: Submit the request through Audi Warranty Online under the Campaigns/Update option.



Canada dealers: Upload the repair order to Audi WIN/Operations/Campaign Closure.
Service Number

97EF

Damage Code

0099

Parts Vendor Code
Claim Type

002
Sold vehicle: 7 10
Unsold vehicle: 7 90

Causal Indicator
Vehicle Wash/Loaner
Criteria I.D.

Mark labor as causal
Do not claim wash/loaner under this action
01
LABOR
Labor Op

Time Units

Description

2706 89 50

10

Connect battery charger

9710 25 99

Time stated on
diagnostic protocol

Update Vehicle Electrical System
Control Module (BCM) software

Additional Actions Some of the affected vehicles may be involved in additional Actions. Please check your
Elsa Campaign/Action Information screen so that any additional required work can be
done simultaneously.
Verifying Vehicle
Eligibility

To verify vehicle eligibility for this Update, always check the Elsa Campaign/Action
Information screen. The Elsa system is the only binding inquiry and verification system;
other systems are not valid and may result in non-payment of a claim.

Help for Claim
Entry

For questions regarding claim entry, contact Audi Warranty.

Required
Customer
Notification

Inform your customer in writing by recording on the Repair Order any and all work that
was conducted on the vehicle, including any and all updates completed under this Update.

The repair information in this document is intended for use only by skilled technicians who have the proper tools, equipment and training to correctly and safely maintain your vehicle. These
procedures are not intended to be attempted by “do-it-yourselfers,” and you should not assume this document applies to your vehicle, or that your vehicle has the condition described. To
determine whether this information applies, contact an authorized Audi dealer. 2020 Audi of America, Inc and Audi Canada All Rights Reserved.
May 2020

97EF Page 8 of 9

Release Date

Technical Service Bulletin

05/29/2020

97EF UPDATE
Vehicle Electrical System Module Software Update – (NVLW)

Required Special Tools
Battery Tester/Charger

Diagnostic Tester

- GRX3000VAS-

-VAS6150X/VAS6160X-

(or equivalent)

(or equivalent)

Additional Information
All parts and service references provided in this Update are subject to change and/or removal. Always check Elsa
for the most current version of this document.

The repair information in this document is intended for use only by skilled technicians who have the proper tools, equipment and training to correctly and safely maintain your vehicle. These
procedures are not intended to be attempted by “do-it-yourselfers,” and you should not assume this document applies to your vehicle, or that your vehicle has the condition described. To
determine whether this information applies, contact an authorized Audi dealer. 2020 Audi of America, Inc and Audi Canada All Rights Reserved.
May 2020

97EF Page 9 of 9