Installation and Conversion Instructions

Macan (95B)
36/16

ENU

9193

9

Apple CarPlay® Interface incl. Voice Control

Revision:

This bulletin replaces bulletin Group 9, 36/16, dated September 26, 2019.
Work procedures have been revised and content has been updated.

Model Year:

As of 2017 up to 2018

Information:

Retrofitting

Figure 1
Notes:

After enabling the Apple CarPlay® interface in the vehicle, iPhone® apps can also be used in the Porsche
Communication Management (PCM) of the vehicle.
The following requirements must be met in order to use this function:
•
•

At least iPhone® 5 or a newer device with iOS® 7.1 or later software
Availability of Apple CarPlay®

You will find information about the available regions at https://support.apple.com.
Different work must be carried out and/or additional parts must be ordered, depending on vehicle
equipment.

Parts Info:

95B.044.900.07

 License key for Apple CarPlay®

Order the following parts in accordance with vehicle equipment:

Tequipment

May 5, 2020
Page 1 of 12

9

Macan (95B)
9193

ENU

Installation and Conversion Instructions

36/16

Vehicles WITHOUT navigation (I-no. 7Q0):
7PP.035.504.A

1x

GPS antenna

95B.035.550.DD

1x

GPS antenna line

999.513.076.40

10 x

Tie-wrap

955.606.838.00

5x

Tie-wrap with clip

Vehicles WITHOUT Voice control (I-no. QH0).
N .910.207.01

1x

Multiple-tooth screw, M18 x 1.5 x 26

95B.953.50x.x

1x

Steering-column switch (see table)

Installed steering-column switch

Required steering-column switch

Part No.

Part No.

95B.953.502.A

95B.953.502.C

95B.953.502.D

95B.953.502.F

95B.953.502.N

95B.953.502.B

95B.953.502.E

95B.953.502.H

95B.953.502.J

95B.953.502.L

95B.953.502.K

95B.953.502.M

95B.953.502.P

95B.953.502.S

95B.953.502.R

95B.953.502.T

Alternatively, the following instructions will help you to identify the required steering-column switch.
1.

1

Tools:

2.

Look for the standard steering-column switch in the Porsche Electronic Parts Catalogue (PET). To
do this, activate the VIN filter in the PET1 .
Take note of the I-nos.

3.

Replace I-no. QH0 (Without voice control) with I-no. QH1 (Voice control).

If the VIN filter in the PET does not work, the standard steering-column switch must be identified based
on the I-no. in the vehicle information (PIWIS information system).

9900 - PIWIS Tester 3
Nr.32 - Multiple-tooth socket-wrench insert
3438 - Hook

Installing:

May 5, 2020
Page 2 of 12

1

Connect battery charger (  Workshop Manual '2X00IN Battery trickle charging').

2

ONLY for vehicles WITHOUT navigation (I-no. 7Q0):
Install GPS antenna and GPS antenna line

Tequipment

Installation and Conversion Instructions

Macan (95B)
36/16

ENU

9193

9

2.1

Remove PCM display and operator control unit (  Workshop Manual '911019 Removing
and installing PCM display and operator control unit').

2.2

Remove glove compartment (  Workshop Manual '681519 Removing and installing glove
compartment').

2.3

Remove air guide (air duct) at the right (
Figure 2 -1-).
1
2
3

2.4

– Air guide (air duct)
– Internal Torx screw
– Hexagon-head bolt

2.3.1

Unscrew hexagon-head bolt.

2.3.2

Release connector ( Figure 2 -a-)
and disconnect it.

2.3.3

Unscrew internal Torx screw and
remove air guide.

Figure 2

Expose A/B-pillar area (at the right)
2.4.1

Remove (right) A-pillar trim panel (  Workshop Manual '705719 Removing and
installing A-pillar trim panel').

2.4.2

Remove front (right) grab handle (  Workshop Manual '683519 Removing and
installing front grab handle').

2.4.3

Remove rear (right) grab handle (  Workshop Manual '683719 Removing and
installing rear grab handle')

Tequipment

May 5, 2020
Page 3 of 12

9

Macan (95B)
9193

ENU

Installation and Conversion Instructions

36/16
2.4.4

Detach upper part of B-pillar trim
panel (at the right) ( Figure 3
,  Workshop Manual '706719
Removing and installing upper part
of B-pillar trim panel').
1

2.5

– Upper part of B-pillar trim
panel

Expose front roof area
2.5.1

Remove roof console (  Workshop
Manual '708319 Removing and
installing front roof trim panel').

2.5.2

Remove cover over the interior
rear-view mirror (  Workshop
Manual '682719 Removing and
installing interior rear-view mirror')

2.5.3

Figure 3
Remove sun visor at the right and
center bearing (  Workshop Manual '682319 Removing and installing sun visor').

2.5.4

Remove center bearing for sun visor at the left.

2.5.5

Remove screw (2 x) in the roof
console area ( Figure 4 ).
1

– Screw on roof console

Figure 4
Information
Check that the fixing clips are not bent or broken.
Replace missing or damaged fixing clips with new ones.
Make sure that all fastening clips are engaged securely.

May 5, 2020
Page 4 of 12

Tequipment

Installation and Conversion Instructions

Macan (95B)
36/16

ENU

9193

9

Check that they are seated correctly. Check gap and joint dimensions.
2.5.6

ONLY for vehicles with panoramic
roof system:
Unclip roof trim panel at the front
and side areas at the fixing clips
( Figure 5 ).

Figure 5
Information
Make sure that the roof cover does not buckle.
2.5.7

Carefully pull front roof trim panel
down as far as required ( Figure 6
-arrow a-) until the clip is no longer
installed in position (roof) ( Figure
6 -arrow b-).
1

– Clip

Figure 6

Tequipment

May 5, 2020
Page 5 of 12

9

Macan (95B)
9193

ENU

Installation and Conversion Instructions

36/16

2.6

Insert GPS antenna into the holder ( Figure
7 ).
1
2

– GPS antenna holder
– Clip

Press GPS antenna up ( Figure 7 -arrow a-)
until the clips (2 x) lock securely ( Figure 7 ).
2.7

Route GPS antenna line as follows:
GPS antenna → roof console → roof →
A-pillar → behind glove compartment → PCM
installation slot
2.7.1

Figure 7
Connect GPS antenna line
connector to the GPS antenna and move locking mechanism.
Information
Make sure that the roof cover does not buckle.

2.7.2

Route GPS antenna line along
the standard wire harness for the