D

Select “ECU Reprogramming”

D

Select :Database File Display−CAN”

D

Confirm the database number displayed at the
top right of the chart is N13112 or higher

(1) If the database number displayed on your
MUT−III is N13112 or greater, continue to the
Reprogramming Procedure on page 5.
(2) If the reprogramming database number
displayed on your MUT−III is lower than
N13112, locate the
reprogramming CD
containing database N13112 and follow the
instructions on the CD label to update your
MUT−III.

Page 5 of 15
SC−13−004

REPROGRAMMING PROCEDURE
CONNECT A BATTERY CHARGER TO THE VEHICLE’S BATTERY DURING THE
REPROGRAMMING PROCEDURE. DO NOT ALLOW THE BATTERY CHARGER TO TIME OUT.
BATTERY VOLTAGE (AS MEASURED AT THE BATTERY POSTS WITHOUT ELECTRICAL LOAD)
MUST BE KEPT AT 12.4V OR HIGHER IN ORDER TO REPROGRAM THE ECM. MEASURE THE
BATTERY VOLTAGE AND CHARGE AS NECESSARY.
NOTE:

VCI Stand−alone reprogramming is not available for this procedure. The laptop and
the VCI must remain connected for the entire procedure.

Connect the equipment as follows:
USB CABLE
VCI − LAPTOP

MEDIC−II / MUT−III
MAIN HARNESS

BLUE END

VCI

MEDIC 3 / MUT−III LAPTOP

D

Turn the laptop computer on. If you’re running on battery power and the charge indicator in the lower
right hand corner of the screen does not show a full charge, it is recommended that either the laptop
battery be charged prior to beginning, or that reprogramming be completed with the A/C power adaptor connected to the laptop.

D

Connect the USB cable to the VCI (or VCI−LITE).

D

When the laptop displays the MUT−III main screen, connect the USB cable to the laptop.

D

Connect the MUT−III main harness (blue DLC connector) to the VCI.

D

Connect the blue connector of the MUT−III main harness to the vehicle’s data link connector.

D

Turn the VCI power switch ON. Verify the indicator lamp in the upper right corner of the screen is green.

CAUTION

DO NOT DISTURB THE HARNESS CABLES OR CONNECTIONS.
INTERRUPTION DURING THE REPROGRAMMING PROCESS COULD CAUSE
THE CONTROL UNIT TO LOSE DATA OR PREVENT FUTURE
REPROGRAMMING. IF THE USB CABLE IS DISONNECTED DURING THIS
PROCEDURE, A WARNING MESSAGE WILL DISPLAY.

Page 6 of 15
SC−13−004

ECU reprogramming
1. Conduct the following steps to reprogram the ECM.
a. Turn the ignition switch to the ON position. If the
vehicle is equipped with the F.A.S.T. System, the
transmitter must remain in the vehicle for the entire
procedure.

Ver. 29

For vehicles equipped with OSS, press the
START/STOP button twice without applying the
brake. The LED in the button should be green.
b. If using MEDIC 3, from the main page, click the
MUT−III STV icon at the top center of the screen.
c. From the MUT−III Main Menu, select “Special
Function.”
d. Select “ECU Reprogramming.”

e. Select “Automatic Reprogramming (CAN).”

Page 7 of 15
SC−13−004

f. Click on the car icon at the bottom of the page.

g. If the VIN or vehicle description displayed does not
match the vehicle you are working on, click on the
eraser icon at the bottom of the page to erase
vehicle data.
Then click on the VIN button.

h. Click the icon in the lower RH corner of the screen
to have MUT−III automatically read the VIN. If a
message appears saying the VIN cannot be input
automatically, manually type the 17 digit VIN into
the VIN field at the top of the page.
Make sure the VIN is correct and click on the check
mark.

Page 8 of 15
SC−13−004

i. Confirm all data matches the vehicle and click the
check mark at the bottom of the page.

j. MFI should be highlighted as the default. If not, click
on it to highlight it.
Click the check mark at the bottom of the page.

k. A message will advise the system will “Automatic
search the data.”
Click the check mark to continue.

Page 9 of 15
SC−13−004

ECM TO LATEST VERSION
If a “Complete Reprogramming” message does not
appear, continue with step l.
If the message seen at left is displayed, the ECM
software as already at the most current level. Do not
continue with the reprogramming procedure. This
Service Campaign Bulletin does not apply.
Click the check mark to clear the window, then click the
Home icon at the lower left corner of the screen to return
to the System Select main page.
Turn the ignition switch to the OFF position and
disconnect the MUT−III. Turn off and disconnect the
battery charger. Conduct normal diagnosis per the
service manual.
l. The Automatic Reprogramming (CAN) database
screen will display.
Confirm the database number at the top right of the
table is N13112 or higher.
If more than one row is displayed in the table, refer
to the ECM Reprogramming Chart on Page 2 to
select the correct row.
Click on the row to highlight it.
Click the check mark to continue.
m. A message will ask you to “Check reprogramming
data.”
n. Click the check mark to begin reprogramming.
Reprogramming will take up to 5 minutes to
complete.

Page 10 of 15
SC−13−004

o. This message will display when ECM
reprogramming is successfully completed. Confirm
the “New S/W P/N” displayed matches the table at
the beginning of this Service Campaign Bulletin.
Then click the check mark to clear the message.
2. Click the home icon at the lower left corner of the
page to return to the MUT−III main page.

3. Using MUT−III, check and erase ALL DTCs from all
systems as follows.
a.

Select “Special Function.”

b.

Select “All DTCs,” then select “ERASE AND
READ ALL DTCS.”

Page 11 of 15
SC−13−004

c.

d.

The “System List” on the left side of the screen will
have all selections checked. Do not change
these selections. DTCs may be set if the vehicle
is equipped with options that are unchecked.
If the check mark at the bottom of the screen is
highlighted, click it and proceed to step 4. If not,
proceed to step e.

NOTE: A “Loading Options Setup” list on the RH side
of the screen must be completed for Lancer
based models. For those models, the check
mark at the bottom of the page is not
highlighted (inactive) at this time. It will
activate when step e is completed.
e.

f.

In the left column, scroll to and click
FAST/IMMOB/KEYLESS/TPMS.
In the right
column, check the correct option code (VF#) from
the Loading Options Setup list. This will activate
the check mark at the bottom of the page.
D

Vehicles with regular keyless entry (buttons on
a multi−function key), select VF2.

D

Vehicles with F.A.S.T. Key, select VF3.

In the left column, scroll to and select METER. A
window will display. Check the correct display
type for the vehicle.
Click the check mark to continue.

4. A window will pop up asking you to confirm DTC
erasing. Click the check mark for DTC erasing and
reading to begin.
5. When DTC erasing is completed, a window will display.
a.
b.

If DTCs return after reprogramming, click the
check mark to clear the window. Diagnose and
repair per the Service Manual.
If DTCs do not return, click the check mark to
clear the window, then click the home icon at the
lower left of the screen to return to the main
menu.

6. Turn off the ignition switch and disconnect the MUT−III.
Turn off and disconnect the battery charger.
7. Using a ball−point pen, enter the appropriate Engine Control Module (ECM) part number, Software
Part Number (ROM ID#), this Service Campaign Bulletin number (SC−13−004), your dealer code, and
the current date on the Engine Compartment / Control Module Label (p/n MSSF024G00). The Vendor
Code is not applicable. The label is available from your facing PDC.

Page 12 of 15
SC−13−004

1860C045

N/A

1860C04501

SC−13−004

99332

12/19/13

The Control Module Label is NOT used for this reflash. It should be discarded.
8. Carefully remove all dirt and oil from a vacant area near the VECI label on the underside of the hood
and affix the Engine Compartment Label (LH side, above) to that area.
9. Test drive the vehicle to confirm proper operation and the MIL does not illuminate. Diagnose and
correct any DTCs that return.

PARTS INFORMATION
Use only the Genuine Mitsubishi Parts listed below.
Description

Model

Part Number

Label, Engine Compartment

All

MSSF024G00

Page 13 of 15
SC−13−004

WARRANTY / SERVICE CAMPAIGN CLAIM INFORMATION
Enter all claims as claim type ’C’ − Recall/Campaign Claims
Please follow the campaign instructions when entering each claim in order to select the
applicable operation code that correctly match up with the work that was actually performed. A
claim example to follow is provided below.
Certain 2008 − 2014 MY − Lancer Evolution, Ralliart, and Ralliart Sportback Vehicles
Required Operation to be performed
1. Reprogram the ECM

Labor Operation
C1311W01

Total Labor Time
.3 hrs.

Claim Header Section: 2008−2014MY Lancer Evolution, Ralliart and Ralliart Sportback ECM Reprogramming

Enter in the first 6 characters of
this campaign labor operation:
C1311W__.

C1311W_ _
45000
JA…………..….

This campaign is for the reprogramming the ECM on
certain 2008−2014MY Lancer Evolution, Ralliart and
Ralliart Sportback vehicle models only.
Check the Open Recall area of the Superscreen each time
to be certain of a vehicle’s eligibility. Only VINs showing
C1311W as open are involved in this campaign.

Page 14 of 15
SC−13−004

After entering the required customer data, vehicle information, Campaign Operation number
and hitting “Save and Continue”, the “Repair Performed” fields will be automatically filled in as
there is only one possible repair scenario for this campaign.

Campaign Claim Example:
Follow these instructions for performing the required 2008−2014MY Lancer Evolution, Ralliart
and Ralliart Sportback ECM reprogramming on involved vehicles.
−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−
PARTS:
No parts are required or allowed to be claimed for this campaign. Leave this page blank.

−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−
LABOR:
The full campaign labor operation number of C1311W01 and the allowed labor time of .3 hours
will be automatically entered as a result of your ’Repair Performed’ selection from the “Vehicle”
page.

−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−
OTHER CHARGES − Only if necessary:

Page 15 of 15
SC−13−004