Turn ignition ON > OFF > ON
ON

Step
55

Figure 32

122/146

NTB17-034L

56. Verify the before and after part numbers are different.

57. Print a copy of this screen (Figure 33) and attach it to the repair order.

58. Select Confirm.

Step
56

Step
57
Step
58

Figure 33

NOTE: If you cannot print the above screen:
a. Select Screen Capture.
b. Name the file.
c. Save the file in My Documents.


A copy of the screen is now saved in the CONSULT PC. It can be retrieved
and printed at a later time.

123/146

NTB17-034L

CONTROL VALVE REPLACEMENT

59. Navigate C-III plus to the screen shown in Figure 34.


Diagnosis (All Systems) > TRANSMISSION > Work support

60. Select CONTROL VALVE REPLACEMENT.

61. Select Start.

Step
60

Step
61

Figure 34

124/146

NTB17-034L

62. Follow the on-screen instructions while maintaining the following conditions:
a.
b.
c.
d.

Turn the ignition ON, with the engine OFF.
Press the brake pedal.
Press the accelerator pedal between ¼ and ½.
Put the shift selector in R.

63. Select Start.

Step
63

Figure 35

64. Release the accelerator and brake (shift selector remains in R).
65. Turn the ignition OFF, then wait 10 seconds.

Figure 36
125/146

NTB17-034L

66. Turn the ignition ON, then wait 10 seconds.

Figure 37

67. Turn the ignition OFF, then wait 10 seconds.

Figure 38

126/146

NTB17-034L

68. Turn the ignition ON.

69. Move the shift selector to P.

Figure 39

70. When COMPLETED is displayed, select End.

Step
70

Figure 40

127/146

NTB17-034L

71. Does the pop-up notification in Figure 41 display?
YES: TCM Programming is not correct for the installed Control Valve. Select OK, then
perform TCM Reprogramming, starting on page 104.
NO: Proceed to step 72 on page 129.

If this notification
displays, perform
TCM
Reprogramming on
page 104.

Figure 41

128/146

NTB17-034L

ERASE LEARNING VALUE

72. Navigate C-III plus to the screen shown in Figure 42.


Diagnosis (All Systems) > TRANSMISSION > Work support

73. Select ERASE LEARNING VALUE.

74. Select Start.

Step
73

Step
74

Figure 42

129/146

NTB17-034L

75. Follow the on-screen instructions; maintain the following conditions:
a.
b.
c.
d.

Parking brake set.
Turn ignition ON, with the engine OFF.
Put the shift selector in R.
Fully depress the accelerator pedal.

76. Select Start.

Step
76

Figure 43

77. When COMPLETED is displayed, select End.

Step
77

Figure 44

130/146

NTB17-034L

CONFORM CVTF DETERIORTN

78. Navigate C-III plus to the screen shown in Figure 45.


Diagnosis (All Systems) > TRANSMISSION > Work support

79. Select CONFORM CVTF DETERIORTN.
80. Select Start.

Step
79

Step
80

Figure 45

81. Select Start.

Step
81

Figure 46
131/146

NTB17-034L

82. Select Clear.

Step
82

Figure 47

83. Select Yes.

Step
83

Figure 48

132/146

NTB17-034L

84. When CVFT DETERIORATION DATE changes to “0”, select End.

0

Step
84

Figure 49

85. Start the engine.

86. Set the parking brake.

87. Turn OFF the A/C.

88. Bring the engine to normal operating temperature range.

89. Confirm the CVT fluid temperature is over 122°F (50°C).

133/146

NTB17-034L

Auxiliary gearbox clutch point learning
90. Navigate C-III plus to the screen shown in Figure 50.


Diagnosis (All Systems) > TRANSMISSION > Work support

91. Select Auxiliary gearbox clutch point learning.
92. Select Start.

Step
91

Step
92

Figure 50

93. Follow the on-screen instructions in Figure 51 and then select Start.

Step
93

Figure 51

134/146

NTB17-034L

94. With the brake pedal still applied, shift the CVT selector lever into the D position.


Figure 52 will be displayed after shifting into the D position.

NOTE: The Current status will show EXECUTING, but until the vehicle is shifted into the
D position Auxiliary gearbox clutch point learning will not begin.

Step
94

Figure 52
95. Continue to depress the brake pedal until the Current status shows “Completed” as
shown in Figure 54 on page 136.
NOTE: This may take several minutes to complete.

Figure 53
135/146

NTB17-034L

96. When COMPLETED is displayed, select End.

Step
96

Figure 54

97. Shift the vehicle into Park, turn the ignition OFF and release the brake pedal.
98. Perform Auxiliary Gearbox Clutch Point Learning (steps 85 to 97) one additional time
(a total of two times).

Erase DTCs

99. Use C-III plus to Erase any transmission DTCs that may have stored.
100. Turn OFF C-III plus.
101. Disconnect C-III plus from the vehicle.
102. Verify the CVT operates normally and no abnormal noises are heard during a test
drive.

Procedure complete.

136/146

NTB17-034L

PARTS INFORMATION

IMPORTANT: The parts lists apply to both Versa Sedan and Versa NOTE unless otherwise
stated.

Belt and Pulley with Control Valve Repair (Sub-Assembly Repair)
DESCRIPTION

PART #

QUANTITY

KIT-CONTROL VALVE
KIT-PULLEY
KIT-OIL PUMP
Loctite 5460 Sealant (1) (2)
Nissan NS-3 CVT Fluid (1) (2)
Additional Engagement Tool O-Rings (5)
Lens Swab packet

3170E-X428B
31214-X429D
31340-X429E
999MP-LT5460P
999MP-CV0NS3
11440
J-51963

1
1
1
(3) (4)
As needed
As needed
(6)

****Single use parts that are not included in the above kits****
DESCRIPTION
GASKET - INTAKE MANIFOLD
(throttle body gasket) (Versa NOTE only)
GASKET - INTAKE MANIFOLD
PIN - COTTER
NUT - LOCK, FRONT WHEEL BEARING
NUT (steering knuckle)
NUT (stabilizer connecting rod to front strut)
NUT (outer socket)
CLAMP (CVT oil cooler hose)
CLAMP (for water hose) (Versa NOTE only)
SEAL - O RING (fill tube)
WASHER – SPRING (manual plate)
NUT - HEX (manual plate)
WASHER-DRAIN
(CVT Oil Pan Drain Plug Gasket)

PART # PREFIX QUANTITY
16175

1

14035
40073
40262
01223
01225
01223
21639
16439
31084
08915
08911

1
2
2
2
2
2
2
2
1
1
1

11026

1

Refer to the footnotes on page 139.

137/146

NTB17-034L

PARTS INFORMATION (continued)

IMPORTANT: The parts lists apply to both Versa Sedan and Versa NOTE unless otherwise
stated.

Control Valve only Repair
DESCRIPTION
KIT-CONTROL VALVE
Nissan NS-3 CVT Fluid (1) (2)
Additional Engagement Tool O-Rings (5)
Lens Swab packet

PART #
QUANTITY
3170E-X428B
1
999MP-CV0NS3 As needed
11440
As needed
J-51963
(6)

****Single use parts that are not included in the above kit****
DESCRIPTION
WASHER – SPRING (manual plate)
NUT - HEX (manual plate)
SEAL– O Ring (secondary speed sensor)
WASHER-DRAIN
(CVT Oil Pan Drain Plug Gasket)

PART # PREFIX QUANTITY
08915
1
08911
1
31526
1
11026

1

Refer to the footnotes on page 139.

138/146

NTB17-034L

PARTS INFORMATION (continued)

IMPORTANT: The parts lists apply to both Versa Sedan and Versa NOTE unless otherwise
stated.

CVT Assembly Replacement
DESCRIPTION

PART #

QUANTITY

CVT Assembly

(7)

1

Nissan NS-3 CVT Fluid (1) (2)

999MP-CV0NS3 As needed

****Single use parts that are not included with the CVT Assembly****
DESCRIPTION
GASKET - INTAKE MANIFOLD
(throttle body gasket) (Versa NOTE only)
GASKET - INTAKE MANIFOLD
PIN - COTTER
NUT - LOCK, FRONT WHEEL BEARING
NUT (steering knuckle)
NUT (stabilizer connecting rod to front strut)
NUT (outer socket)
CLAMP (CVT oil cooler hose)
CLAMP (for water hose) (Versa NOTE only)
SEAL - O RING (fill tube)
WASHER-DRAIN
(CVT Oil Pan Drain Plug Gasket)

PART # PREFIX QUANTITY
16175

1

14035
40073
40262
01223
01225
01223
21639
16439
31084

1
2
2
2
2
2
2
2
1

11026

1

(1) For warranty repairs, Nissan NS-3 CVT Fluid and Loctite 5460 Sealant must be used.
For customer pay repairs, Nissan NS-3 CVT Fluid and Loctite 5460 Sealant or their
equivalents are recommended.
(2) Nissan NS-3 CVT Fluid and Loctite 5460 Sealant can be ordered through the Nissan
Maintenance Advantage program: Phone: 877-NIS-NMA1 (877-647-6621) or Website:
Order via link on dealer portal www.NNAnet.com and click on the “Maintenance
Advantage” link.
(3) One container of Loctite 5460 Sealant is good for approximately 5 repairs. This sealant
is not included in any kit.
(4) Bill out Loctite 5460 Sealant (or equivalent) under expense code 008. Do not include
the Loctite 5460 Sealant part number on the claim.