Ferrari North America
Technical Information

Date:
Bulletin #:
Campaign #:
Supersedes:
Section:

March 2020
2655
10

Model:
Subject:

Pre-Delivery Inspection – PDI procedures

Please find enclosed the new procedures and relative list of inspections to be performed at all times
before the vehicle is delivered to the customer.
The following procedures must be performed exactly as indicated and in the order given, providing the
factory with the information requested.
- IMPORTANT This Pre-Delivery Inspection (PDI) procedure may only be performed with a PC-Tester DEIS
updated to at least the following software version (or subsequent release):
- Module 0

Portal and Troubleshooting

54

- Module 1

DEIS Diagnostic software

88

- Module 2

Technical Documentation

12

- Module 3

Tools

8

Check the software number and, if necessary, update your DEIS Tester immediately.
After updating the DEIS, the first vehicle diagnostic cycle must be performed using a cable
connection.

Procedure.

1.

Visually inspect condition of vehicle paintwork; repair if necessary (use the specific “Bodywork
defects” form annexed on page 9).

2.

If disconnected, connect the negative pole of the battery and reset the vehicle auto-adaptive
parameters (as described in paragraph F3.01 of the Workshop Manual).

3.

Activate the Key-ON status and check which letter appears on the DOT MATRIX display:
- if letter “P” (Park Lock) is displayed, go to point 5.
- if letter “N” (Neutral) is displayed, go to point 4.

© 2020. Ferrari North America, Inc.
Technical Department
www.ferrari.com

All rights reserved. Reproduction or translation in
whole or in part is not permitted without
authorization from the publisher. Printed in USA.

Ferrari North America
4.

Re-enable the Park Lock – Gearbox lock device (as described in paragraph C2.07 of the
Workshop Manual).

5.

Remove the engine compartment cosmetic shields (as described in paragraph E3.03 of
the Workshop Manual); Perform the “Battery Certification” procedure (TI 2079 /
2230), and compile the relative form. If necessary, remove the battery from the vehicle
and charge using the “SLOW charge ” procedure (TI 2078).

6.

Using the DEIS tester, disable the “Logistic Mode” function with diagnostic cycle “150
Complete Logistic Mode” on the NBC ECU (Body Computer Node).

7.

Test the keys and the anti-theft system.

8.

Check that the daytime lights work correctly (depending on market).

9.

Check that the low beams work correctly: also check that the AFS system (adaptive front
lights - if applicable) works correctly by turning the steering wheel.

10. Check that the vehicle front lift (if present) is working: check the AFS system is working
(low beam orientation). With the car raised, the height of the light beam must be equal
to the height with the car lowered.
11. Check that the high beams work correctly.
12. Check that the stop lights work correctly.
13. Check that the turn indicators and license plate lights work correctly.
14. Check that the door lights, vehicle interior light and luggage compartment lights work
correctly.
15. Check that the button backlights on the dashboard, driver side door, center console,
ceiling light unit and USB socket light work correctly.
16. Try the horn.
17. Check that the power windows and “BackLite” rear screen work correctly.
18. Check that the windscreen and headlight wipers work correctly.
2
© 2020. Ferrari North America, Inc.
Technical Department
www.ferrari.com

TI-2655

All rights reserved. Reproduction or translation in
whole or in part is not permitted without
authorization from the publisher. Printed in USA.

Ferrari North America
19. Check that the mechanical/electrical steering adjustment mechanism works correctly.
20. Check that the seats work correctly.
21. Check that the electric parking brake (EPB) works correctly; test manual and automatic
modes.
22. Check that the Hi-Fi (if applicable) / Navigation system (if applicable) work (see point
35); set the relative roadside assistance numbers for your market.
23. Check the coolant level and top up if necessary.
24. Check the brake fluid level and top up if necessary.
25. Check the headlight washer/windscreen washer fluid level and top up if necessary.
26. Check tire pressure calibration with the TPMS system.
27. Check the tightening of the wheel studs with a torque wrench (as described in paragraph
D2.01 of the Workshop Manual).
28. Check that the tow hook can be fitted correctly.
Start engine and perform the following:
29. Perform two complete roof open/close cycles.
30. Check that the air conditioning and heating system works correctly (static test).
31. Check that the electric rear view mirrors work correctly.
32. Check that the internal electrochromic mirror and the electrochromic RH and LH rear
view mirrors (if installed) work correctly.
33. Check that the parking sensors and rear and front camera (if installed) work correctly.
34. Using the DEIS tester, perform the “Cancel all DTCs from all ECUs” procedure from the
“Vehicle functions” menu.
3
© 2020. Ferrari North America, Inc.
Technical Department
www.ferrari.com

TI-2655

All rights reserved. Reproduction or translation in
whole or in part is not permitted without
authorization from the publisher. Printed in USA.

Ferrari North America
Test drive.
35.

Check that the navigation system works correctly (if applicable); set route before setting off.

36. Test drive the vehicle (approx. 20 minutes).
37. Check that Stop&Start system works correctly.
38. While driving, check that the “Suspension damping decoupling” button and
“Manettino” dial on the steering wheel work correctly.
39. Check that the telemetry kit works (if applicable).
40. While driving, check that the air conditioning and heating system works correctly
(dynamic test).
41. For USA/CND Version only. Take the vehicle into a location with a clear view of the sky
and activate Sirius XM as per FNA 165.
Return to workshop.
42. Check the engine oil level (engine warm and at idle speed) and top up if necessary (as
described in paragraph B8.02 in the Workshop Manual).
43. With the DEIS tester, check that the VIN number read with the tester matches the VIN
number of the vehicle; if necessary, the VIN number read with the tester may be modified
using the “100 VIN Writing” diagnostic function (password-protected) on the NCM
ECU (engine control node). Any faults must be reported in an ROL.
44. Check and cancel the errors on all ECUs.
45. Enter the warranty start date (Check that the language setting on the TFT display is
correct).
46. Perform the “SCAN OUT” procedure from the “Vehicle functions” menu with the DEIS
tester before carrying out any further diagnostic operations.
47. Remove the complete aerodynamic undertray, the engine compartment cosmetic shields
and the RHT container tub from the vehicle (as described in paragraphs E3.01 and E3.03
of the Workshop Manual).
4
© 2020. Ferrari North America, Inc.
Technical Department
www.ferrari.com

TI-2655

All rights reserved. Reproduction or translation in
whole or in part is not permitted without
authorization from the publisher. Printed in USA.

Ferrari North America
48. Visually check for coolant and/or oil leaks in the underbody area and engine
compartment.
49. Visually inspect engine compartment lines.
50. Visually inspect the engine compartment wiring harnesses.
51. Visually inspect underbody lines.
52. Visually inspect exhaust pipes.
53. Visual inspection of fuel tanks.
54. Check visually that the following are fitted correctly: Suspension components, steering
box and axle shaft flanges.
55. Check visually that the following are fitted correctly: Vehicle ground and engine-chassis
ground.
56. Visually inspect condition of brake pads and discs (DO NOT remove wheels).
57. Check condition of tires and wheels.
58. Visually check that the water drain holes in the rear window seal are not obstructed.
59. Refit the aerodynamic floor and the engine compartment panels and the RHT container
tub (as described in paragraph E3.01 and E3.03 of the Workshop Manual).
60. Check that the door and lid locks work correctly; adjust if necessary.
61. Check that the fuel filler flap emergency release works correctly; adjust if necessary.
62. Visually inspect condition of vehicle interior; repair if necessary.
63. Thoroughly clean interior and wash car.

5
© 2020. Ferrari North America, Inc.
Technical Department
www.ferrari.com

TI-2655

All rights reserved. Reproduction or translation in
whole or in part is not permitted without
authorization from the publisher. Printed in USA.

Ferrari North America
64. Ensure that the vehicle is delivered complete with the following:
- identification and type approval plates
- license plate holder
- tool kit
- on-board documentation (Owner's Manual, Quick Reference Guide, Warranty
Booklet, Safety Device Booklet and Battery Conditioner Quick Guide card), second
vehicle key and code card, and any material related to options.
65. Check that the battery conditioner provided with the vehicle works correctly, referring to
the relative manual.

- IMPORTANT Confirm that the operations listed above have been carried out correctly with the “Pre-Delivery
Inspection - PDI” form (enclosed on pages 7 and 8, compiled in full and signed by the Aftersales
Manager of your Service Center.
After the inspection procedures, ALWAYS open an ROL (Red On Line) specifying “PDI Form
Info” as the description, and attach the duly compiled “PDI Pre-Delivery Inspection” form
together with the printout files of the parameters and errors requested in points 34 and 46.
You will also be required to open a separate individual ROL with the description "PDI Fault
Info" for each fault encountered during the inspection procedure, indicating the respective
operation number as cited in the “PDI Pre-Delivery Inspection” form; Attach all necessary
documentation, including photographs if needed.

Thank you for your co-operation.

6
© 2020. Ferrari North America, Inc.
Technical Department
www.ferrari.com

TI-2655

All rights reserved. Reproduction or translation in
whole or in part is not permitted without
authorization from the publisher. Printed in USA.

Pre-Delivery Inspection - PDI form

Page 01 of 02

Model

Updated on
February 2020

Chassis number:

Dossier creation date:

Job order no.:
Notes:
Description of inspection / operation:
1. - Condition of vehicle paintwork.
2. - Connect battery and reset vehicle parameters.
3. - Check Park Lock device.
4. - Reset Park Lock device.
5. - “Battery Certification” procedure.
6. - Disable “Logistic Mode”.
7. - Test the keys and the anti-theft system.
8. - Daytime running lights.
9. - Low beams.
10. - Check vehicle front lift system (if applicable).
11. - High beams.
12. - Stop lights.
13. - Turn indicators and license plate lights.
14. - Door lights, vehicle interior light and luggage compartment light .
15. - Button backlights on dashboard, center tunnel console
and door, ceiling light unit and USB socket light.
16. - Horn.
17. - Power windows and BackLite rear screen.
18. - Windscreen and headlight wipers.
19. - Steering wheel adjustment.
20. - Seats.
21. - Electric parking brake (EPB); manual/auto.
22. - Hi-Fi system / Navigation system (if applicable) (see point 36).
23. - Coolant level.
24. - Braking system fluid level.
25. - Windscreen washer/headlight washer fluid level.
26. - Tire pressure calibrated with TPMS.
27. - Tightening of wheel stud bolts.
28. - Tow hook.
29. - *Complete retractable hard top open/close cycles.
30. - *Air conditioning and heating system (static test).
31. - *Electric rear-view mirrors.
32. - *Electrochromic rear view mirrors (if applicable).
33. - *Parking sensors and rear/front camera.
34. - Cancel all DTCs from all ECUs.
35. - Navigator (if applicable): Set route.
36. - Test drive (20 min.).
37. - Stop&Start.
(*) With engine running

Technical Service Department
Page 7 of 9

Performed
OK















Performed
NOT OK

































































R.O.L. N°
(if NOT OK)

Pre-Delivery Inspection - PDI form

Page 02 of 02

Model

Updated on
February 2020

38. - Suspension damping decouple button and “Manettino”.
39. - Telemetry kit (if applicable).
40. - Air conditioning and heating system (dynamic test).
41. - for USA / CND ONLY _ Sirius XM Activation
42. - Engine oil level (warm engine – at idle speed).
43. - Verify VIN from NCM parameters.
44. - Check and cancel ECU errors.
45. - Enter warranty start date.
46. - Perform “SCAN OUT” procedure.
47. - Removal of flat undertray, engine compartment shields and
RHT tub.
48. - Water and/or oil leaks in vehicle underbody .
49. - Engine compartment lines.
50. - Engine compartment wiring.
51. - Underbody lines.
52. - Exhaust pipes.
53. - Visual inspection of fuel tanks.
54. - Visual inspection: Suspension components, etc.
55. - Visual inspection of ground connections: vehicle and
engine-chassis ground.
56. - Condition of brake pads and discs (DO NOT remove wheels).
57. - Condition of tires and wheel rims.
58. - Visual inspection to check that water drain holes are not
obstructed.
59. - Reassembly of flat undertray, engine compartment shields
and RHT tub.
60. - Door and lid locks.
61. - Petrol filler flap emergency opening.
62. - Condition of vehicle interior.
63. - Clean interior and wash car.
64. - Material provided with vehicle: Identification plates, toolkit, etc.
65. - Functional test of battery conditioner









































































Task performed by (Dealer):
Technical Manager:
First name

Last Name
(Print)

(Print)

Company stamp

Full signature
Vehicle delivery date:
Technical Service Department
Page 8 of 9

Bodywork Defects Form

Technical Service Department
Page 9 of 9