2.3.2

Route GPS antenna line  Figure 6
-1- along the wire harness for the
dashboard (glove compartment).

Figure 6

Tequipment

Mar 5, 2020
Page 5 of 18

9

982
9122

Installation and Conversion Instructions

ENU 25/19

2.3.3

Route GPS antenna line  Figure 7
-1- to the PCM central connector.

Figure 7
The GPS antenna line  Figure 8
-1- must protrude approx. 7 cm
beyond the PCM central connector
 Figure 8 -2-.
X

– 7 cm

Figure 8

2.4

2.3.4

Clip three clip-on tie-wraps  Figure
9 -2- into the A-pillar.

2.3.5

Pull GPS antenna line  Figure 9
-1- back and fold it to form a loop
close to the A-pillar.
Secure GPS antenna line using the
two upper tie-wraps.

Carry out concluding work for installing GPS
antenna and GPS antenna line.
2.4.1

Install A-pillar trim panel at the right.

 Workshop Manual '705719
Removing and installing A-pillar trim
panel'

Mar 5, 2020
Page 6 of 18

Figure 9

2.4.2

Install front roof trim panels at the sides.  Workshop Manual '708319 Removing
and installing front roof trim panel'

2.4.3

Install front lock.  Workshop Manual '610519 Removing and installing front lock'

Tequipment

Installation and Conversion Instructions

982
25 / 19 ENU

9122

9

2.4.4

Install center roof trim panel.  Workshop Manual '708319 Removing and
installing front roof trim panel'

2.4.5

Install sun visors and sun visor holders.  Workshop Manual '682319 Removing
and installing sun visor'

3

For vehicles with UI2, continue with Step 6.

4

Install connecting line 9P1.979.002 (USB interface → connection point in center console).
4.1

Disconnect connector from 12-volt plug
socket and secure it to the center console
with adhesive tape  Figure 10 -1-.

4.2

Remove 12-volt plug socket from center
console.  Workshop Manual '905819
Removing and installing plug socket'

Figure 10
4.3

Clip USB interface  Figure 11 -1- into
center console  Figure 11 -2- ( Figure 11
-a-).

Figure 11

Tequipment

Mar 5, 2020
Page 7 of 18

9

982
ENU 25/19

9122

4.4

Installation and Conversion Instructions

Connect electric plug connection  Figure
12 -4- ( Figure 12 -a-).
Secure connecting line (USB interface →
connection point in center console)  Figure
12 -1- to the standard wire harness using a
tie-wrap  Figure 12 -2- and adhesive tape
 Figure 12 -3-.
It must project  Figure 12 -A- by approx. 40
mm on the standard connector  Figure 12
-5-.

5

Install connecting line 9P1.979.004 (USB/iPod
control unit → glove box).
5.1

Figure 12

Install USB/iPod control unit holder.
5.1.1
5.1.2

Unscrew screw  Figure 13 -1from drawer at the top.
Insert USB/iPod control unit holder

 Figure 13 -2- and secure with
screw  Figure 13 -1-.

Figure 13

Mar 5, 2020
Page 8 of 18

Tequipment

Installation and Conversion Instructions
5.2

Release USB line  Figure 14 -3- as well as
RD line  Figure 14 -1- and BU line  Figure
14 -2- from the standard wire harness for the
multimedia interface (PCM → glove box).

5.3

Install connecting line 9P1.979.004
(USB/iPod control unit → glove box).

982
25 / 19 ENU

9122

9

Figure 14
5.3.1

Route connecting line  Figure
15 -1- from PCM drawer  Figure
15 -3- parallel to the standard
wire harness for the multimedia
interface (PCM → glove box) 
Figure 15 -2-.

Figure 15
5.3.2

Pull back connecting line  Figure
16 -a- until the violet connector 
Figure 16 -1- is at the USB/iPod
control unit holder  Figure 16 -2-.

Figure 16

Tequipment

Mar 5, 2020
Page 9 of 18

9

982
9122

Installation and Conversion Instructions

ENU 25/19

5.3.3

Secure the released USB line, RD
line, BU line and extra length of the
connecting line to the standard wire
harness  Figure 17 -2- using a
tie-wrap.
1
3
4

5.4

– Connecting line
– Ventilation duct
– Instrument panel bracket

Install power supply wire harness.

Figure 17
5.4.1

Route power supply wire harness

 Figure 18 -1- from USB/iPod
control unit holder  Figure 18 -2to the PCM central connector.

Figure 18
5.4.2

Release green plug socket 
Figure 19 -1- ( Figure 19 -a-)
and press it out of the PCM central
connector  Figure 19 -2- (
Figure 19 -b-).

Figure 19

Mar 5, 2020
Page 10 of 18

Tequipment

982

Installation and Conversion Instructions
5.4.3

25 / 19 ENU

9122

9

Open secondary lock  Figure 20
-1- ( Figure 20 -arrow-).
Release socket contacts using
a suitable press-out tool and
press lines out of the PCM central
connector.

Figure 20
Color of wire

Chamber

RD (USB+)

C3

BU (USB-)

C4

Secure the RD and BU lines you pressed out to the standard wire harness using
wrapping tape.
5.4.4

Crimp RD line  Figure 21 -1- from
power supply wire harness and new
socket contact  Figure 21 -2together.
Information
Ensure socket contact is seated
securely.
Insert socket contact into chamber
C3.
Close secondary lock  Figure 21
-3-.

5.4.5

Figure 21

Insert green plug socket into the central connector.

Tequipment

Mar 5, 2020
Page 11 of 18

9

982
9122

ENU 25/19

5.4.6

Installation and Conversion Instructions
Release socket contact using a
suitable press-out tool  Figure 22
-3- and press line out of the PCM
central connector  Figure 22 -a-.

Figure 22
Color of wire

Chamber

BN

D17

RD/YE

D18

Information
Ensure socket contact is seated securely.
5.4.7

Crimp pressed-out BN line  Figure
23 -1- and BN/WH line  Figure
23 -2- from the power supply wire
harness together using a new
socket contact (double connector)
and insert them into chamber D17
on the central connector.
Information
Ensure socket contact is seated
securely.
Figure 23
Crimp pressed-out RD/YE line
and RD/YE line from the power supply wire harness together using a new socket
contact (double connector) and insert them into chamber D18 on the central
connector.

Mar 5, 2020
Page 12 of 18

Tequipment

Installation and Conversion Instructions
5.4.8

982
25 / 19 ENU

9122

9

Secure yellow connector from
standard wire harness for the
multimedia interface (PCM →
glove box)  Figure 24 -1- to
the standard wire harness with
wrapping tape.
Secure power supply wire harness
to the standard wire harness 
Figure 24 -2- with wrapping tape.

Figure 24
5.5

Install USB/iPod control unit.
5.5.1