2.3

Route electric wire harness as follows
( Figure 6):
Left A-pillar → main wire harness in
passenger compartment at the left →
cable duct in front of rear seat → main wire
harness in passenger compartment at
the right → left A-pillar → wire harness in
luggage compartment at the right → rear-end
electronics control unit

Figure 6
2.3.1

Push pin connector socket onto the
top guide ( Figure 7 -inset-) at the
connection point holder ( Figure 7
-arrow-).
1
2
3
4

–
–
–
–

Pin connector socket
Connection point holder
Guide, top
Ground pin 21

Secure cable ring eyelet to ground
pin 21 ( Figure 7).
Tightening torque 9 Nm
(6.5 ftlb.)
2.3.2

Figure 7

Open rear left cable duct ( Figure
8 -arrow-).

Figure 8

Mar 4, 2020
Page 6 of 17

Tequipment

Installation and Conversion Instructions
2.3.3

Macan (95B)
23/14

ENU

6807

6

Route electric wire harness along
the main wire harness in the
passenger compartment at the left
through the cable duct in front of the
rear seat to the right-hand side of
the vehicle ( Figure 9).
1
2
3

– Wire harness
– Main wire harness in
passenger compartment
– Cable duct
Figure 9

2.3.4

Close rear left cable duct ( Figure
10 -arrow-).

Figure 10
2.3.5

Route electric wire harness (YE/GY
line) along the main wire harness in
the passenger compartment to the
right A-pillar ( Figure 11).

Figure 11

Tequipment

Mar 4, 2020
Page 7 of 17

6

Macan (95B)
6807

ENU

Installation and Conversion Instructions

23/14
2.3.6

Insert pin contact of YE/GY line into
pin connector socket ( Figure 12
-a-).
1
2

– Pin contact of YE/GY line
– Secondary lock

Close secondary lock ( Figure 12
-b-).

Figure 12
2.3.7

Push pin connector socket onto the
top guide at the connection point
holder ( Figure 13).
1
2
3

– Pin connector socket
– Guide, top
– Ground pin 22

Secure cable ring eyelet to ground
pin 22 ( Figure 13 -3-).
Tightening torque 9 Nm
(6.5 ftlb.)
Figure 13
2.3.8

Route YE/GY line along the
wire harness in the luggage
compartment at the right to the
rear-end electronics control unit
( Figure 14).
1
2

2.4

– YE/GY line
– Control unit for rear-end
electronics

Connect YE/GY line to the rear-end electronics control unit.
Figure 14

Mar 4, 2020
Page 8 of 17

Tequipment

Installation and Conversion Instructions
2.4.1

Macan (95B)
23/14

ENU

6807

6

Disconnect electric plug connection
on the rear-end electronics control
unit ( Figure 15,  Workshop
Manual '578919 Removing and
installing control unit for rear-end
electronics').
1

– Plug connection

Figure 15
2.4.2

Open the locking mechanism (
Figure 16 -arrow-) and push the
grey plug socket out of the black
plug carrier ( Figure 16).
1
2

– Plug socket (grey)
– Plug carrier (black)

Figure 16
Information
Ensure socket contact is seated securely.
2.4.3

Insert socket contact into chamber
8 of the grey plug socket ( Figure
17 -arrow-).

2.4.4

Slide grey plug socket into the plug
carrier until the locking mechanism
engages.

Figure 17

Tequipment

Mar 4, 2020
Page 9 of 17

6

Macan (95B)
6807

ENU

Installation and Conversion Instructions

23/14
2.4.5

Connect electric plug connection
to the rear-end electronics control
unit ( Figure 18,  Workshop
Manual '578919 Removing and
installing control unit for rear-end
electronics').
1

2.5

– Plug connection for
rear-end electronics
control unit

Secure electric wire harness to the standard
wire harness with a tie-wrap.

Figure 18

Information
Some of the repair illustrations show only one side of
the vehicle. Naturally, some steps also have to be performed on the opposite side of the vehicle as
well. These must be carried out as a mirror image of the steps shown.
3

Install illuminated door entry guard in (inner) door sill
trim
3.1

Remove standard door entry guard.
3.1.1

Bend up tabs ( Figure 19
-arrow-).
1

– Tab on door entry guard

Figure 19

Mar 4, 2020
Page 10 of 17

Tequipment

Installation and Conversion Instructions
3.1.2

Macan (95B)
23/14

ENU

6807

6

Carefully lever off the standard door
entry guard from the (inner) door sill
trim using a POM (plastic) wedge
( Figure 20).
1
2
3

– POM wedge
– Door entry guard
(standard)
– (Inner) door sill trim

Figure 20
3.2

Drill cable hole (Ø = 18 mm) in the (inner) door
sill trim ( Figure 21).
x
y
d
s

3.3

–
–
–
–

426 mm
40 mm
Ø 18 mm
Point of intersection

3.2.1

Mark point of intersection ( Figure
21 -S-) of dimensions x and y on the
inner door sill trim.

3.2.2

Drill a hole with a diameter of 18
mm at this point.

Figure 21

Install illuminated door entry guard in (inner) door sill trim.
3.3.1

Pull protective film off the door
entry guard ( Figure 22).
1
2
3

– Line (flat conductor path)
– Protective film
– Tab

Guide connector and line (flat
conductor path) through the bore
hole.
Information
When installing the door entry
Figure 22
guard, make sure that the
sharp-edged tabs do not damaged the surface of the door sill trim.

Tequipment

Mar 4, 2020
Page 11 of 17

6

Macan (95B)
6807

ENU

Installation and Conversion Instructions

23/14

Position illuminated door entry guard over the (inner) door sill trim.
Carefully guide tabs on the illuminated door entry guard into the mounting points on
the (inner) door sill trim ( Figure 22).
3.3.2

Press illuminated door entry guard
and (inner) door sill trim together
and bend over the tabs ( Figure
23).
1

– Tab

Figure 23
3.3.3

Clean the bonding areas for the
flat conductor path ( Figure 24
-shaded area-) on the underside
of the (inner) door sill trim using
isopropanol to remove any grease
and dust.
1
2

– Protective film
– Flat conductor path

Pull protective film off the flat
conductor path ( Figure 24).
Figure 24
3.3.4

Lift up insulating material and affix
flat conductor path to the (inner)
door sill trim ( Figure 25).
1
2

4