– Air guide (bottom), closed
– Torx tapping screw, TP5 x
16
– Radiator grille (center)

Torx tapping screw, TP5 x 16:
Tightening torque 2 Nm
(1.5 ftlb.)
2.9

3

Mar 4, 2020
Page 12 of 17

Figure 15

Route new electric wire harness in the front apron and connect it (  Workshop Manual
'971519 Removing and installing front wire harness').

Fit new SportDesign front apron

Tequipment

Installation and Conversion Instructions
3.1

Macan (95B)
2/19

ENU

6699

6

Work in the vehicle front area
1
2
3
3.1.1

– Plastic foam strip (front)
– Air flap (right)
– Air guide on charge-air cooler (right)
Replace plastic foam strip (front

 Figure 16 (Turbo) -1-) with new
plastic foam strip (  Workshop
Manual '631019 Removing and
installing front bumper').

4

3.1.2

Replace air flap (left/right  Figure
Figure 16 (Turbo)
16 (Turbo) -2-) with new air flap
(left/right) (  Workshop Manual '631019 Removing and installing front bumper')

3.1.3

Replace air guide for charge-air cooler (left/right  Figure 16 (Turbo) -3-) with new
air guide (left/right) (  Workshop Manual '211019 Removing and installing air
guide for charge-air cooler').

3.2

Install new SportDesign front apron with new underbody panelling (left/right) (  Workshop
Manual '631519 Removing and installing front apron').

3.3

Fit new license plate bracket on new SportDesign front apron (  Workshop Manual '668319
Removing and installing number plate cover';  Workshop Manual '668319 Removing and
installing number plate cover (USA)').

Convert rear apron
4.1

Remove rear skirt (  Workshop Manual '636819 Removing and installing rear skirt').
Information
Check fixing clips. They must not be bent or broken.
Make sure that all locking lugs have engaged correctly.

Tequipment

Mar 4, 2020
Page 13 of 17

6

Macan (95B)
6699

ENU

Installation and Conversion Instructions

2/19

Check that they are installed correctly.
4.2

Install new painted rear skirt in rear apron
( Figure 17;  Workshop Manual '636819
Removing and installing rear skirt')
1
2
3
4

–
–
–
–

Painted rear skirt
Rear apron
Installation position of reversing light
Painted rear panel

Check gap dimension in the visible area all the
way around and correct it if necessary.
4.3

ONLY for vehicles with reversing camera
Figure 17
(7XB/8A4):
Install reversing camera (  Workshop Manual '914319 Removing and installing reversing
camera').

4.4

Install reversing light (left/right) (  Workshop Manual '947419 Removing and installing
reversing light').
Check gap dimension in the visible area all the way around and correct it if necessary.

4.5

Install new painted rear panel ( Figure 17 -4-) (  Workshop Manual '635619 Removing
and installing rear panel')
Check gap dimension in the visible area all the way around and correct it if necessary.

4.6

Install rear apron with new underride guide
( Figure 18;  Workshop Manual '635519
Removing and installing rear apron').
1
2
3
4

4.7
5

6

Mar 4, 2020
Page 14 of 17

–
–
–
–

Underride guard
Painted rear panel
Painted rear skirt
License plate carrier

Convert license plate bracket.

Convert rear spoiler.
5.1

Remove rear spoiler (  Workshop Manual
'665819 Removing and installing rear spoiler').

5.2

Install new rear spoiler painted in exterior color.

ONLY for retrofitting SportDesign package (high-gloss Black - 2D6):
Convert door trim panels

Tequipment

Figure 18

Installation and Conversion Instructions

Coding:

7

Macan (95B)
2/19

ENU

6699

6

6.1

Remove cover on front door and install new painted cover (  Workshop Manual '662219
Removing and installing cover for front door').

6.2

Remove cover on rear door and install new painted cover (  Workshop Manual '664219
Removing and installing cover for rear door').

Enter SportDesign package (2D2 or 2D6) in the vehicle data
7.1

Preparatory work – Coding

NOTICE
Voltage drop
•

Risk of irreparable damage to control unit

•

Risk of damage to control unit

•

Fault entries in the control unit

•

Coding in the control unit is aborted

•

Malfunctions in control unit, even during programming



Switch off the ignition and remove the ignition key before disconnecting the control unit.



Ensure that the power supply is not interrupted during programming.



Connect a battery charger with a current rating of at least Nominal value 90 A to the vehicle
battery.
NOTICE

Control unit programming will be aborted if the Internet connection is unstable.
•

An unstable Internet connection can interrupt communication between PIWIS Tester III and the
vehicle communication module (VCI). As a result, control unit programming may be aborted.



During control unit programming, always connect PIWIS Tester III to the vehicle communication module (VCI) via the USB cable.
7.1.1

9900 - PIWIS Tester 3 must be connected to the vehicle and then switched on.

7.1.2

Switch on ignition AND hazard warning lights on the vehicle.
Information
The 9900 - PIWIS Tester III instructions take precedence since the description
may be different with later Tester releases.
The procedure described here has been structured in general terms; different text
or additions may appear on the 9900 - PIWIS Tester III.

7.1.3

Select the "Diagnostics" menu item on the PIWIS Tester.

Tequipment

Mar 4, 2020
Page 15 of 17

6

Macan (95B)
6699

ENU

2/19
7.1.4

7.2

Installation and Conversion Instructions
If 9900 - PIWIS Tester 3 is connected correctly, a connection to the vehicle will be
established: "Macan model line" is detected.

Enter the new vehicle equipment in the vehicle data
7.2.1

Press •F7“ in the control unit overview to switch to the “Additional menu”.
Press •F12“ to confirm the question "Create Vehicle Analysis Log (VAL)?".

7.2.2

Select the “Management of vehicle order” function. Continue pressing •F12“ until
“PR numbers” is displayed in the Value group column.

7.2.3

Look for the option "2D2 – SPORT DESIGN PACKAGE WITHOUT SILL COVERS" or
"2D6 – SPORT DES. PACKAGE W/O DOOR SILLS, BLACK" in the "Family" column.
Select the relevant option from the drop-down menu in the "Value" column.

7.3

7.2.4

Press •F12“ to continue. A table containing coding values (old and new value) is
displayed in the overview.

7.2.5

Press •F8“ to continue. Data is then written/stored.

7.2.6

Wait until the message “Creation of vehicle data has been completed.” appears.
Press •F12“ to go to Report management.

7.2.7

Press •F10“ to open the log. Check that the selected vehicle equipment has been
entered and close the log.

Code/program the new vehicle equipment.
7.3.1

Select ALL control units (•CTRL+A“) in the control unit overview and switch to
the “Coding/programming” column.

7.3.2

Select the coding mode "Automatic coding". Press •F12“ to continue.

7.3.3

Once "Automatic coding" is complete, the message “Coding was completed
successfully. Press •F12“ to continue.” appears in the header.
Switch to the control unit overview.

51 01 71 05:

Mar 4, 2020
Page 16 of 17

7.4

Read out the fault memory of all systems, work through any existing faults and erase the fault
memory (  Workshop Manual '0X03IN Diagnostic maintenance: Diagnostic system and
maintenance inter...').

7.5

Switch off ignition and disconnect 9900 - PIWIS Tester 3.

7.6

Disconnect battery charger. (  Workshop Manual '2X00IN Battery trickle charging').

–Preparing body paintwork–
Includes:
Order-based
Painting of new parts, Step 1
Plastic component

Tequipment

Labor time: 130 TU

Installation and Conversion Instructions

Macan (95B)
2/19

ENU

6699

6

66 99 61 51:

–Painting new parts in SportDesign package (1 x), complete
Includes:
Painting new parts, Step 1:
Front apron, towing hook cover, front spoiler, radiator grille
(center), air grille (left/right), vane (left/right), trim on direction
indicator/auxiliary headlights (left/right), trim panel (left/right)
and front camera trim;
roof spoiler, rear skirt and rear panel.
Materials: 38 MU

Labor time: 510 TU

66 99 23 10:

–Installing SportDesign package (1 x)–
Includes:
Removing and installing front and rear apron.
Assembling new front apron and converting rear apron.
Removing rear spoiler and installing new rear spoiler.

Labor time: 630 TU

03 35 00 50:

–On-board diagnosis–
Includes:
Coding SportDesign package (I-no. 2D2 or I-no. 2D6) in the
vehicle data using the PIWIS Tester.

Additional
working times:

ONLY for retrofitting SportDesign package (high-gloss Black – 2D6):

Labor time: 12 TU

66 22 61 51: Painting new front door trim panel

Labor time: 20 TU

66 42 61 51: Painting new rear door trim panel

Labor time: 20 TU

66 22 56 00: Replacing front door trim panel (left/right)

Labor time: 75 TU

66 42 56 50: Replacing rear door trim panel (left/right)

Labor time: 58 TU

ONLY for vehicles with Lane Change Assist/Lane Keep Assist (7Y2/7Y3/7Y7):
97 70 25 53: Programming Lane Change Assist control unit.
Includes:
Calibrating calibration plate on the vehicle.

Labor time: 47 TU

ONLY for vehicles with Surround View (8A4):
91 72 25 50: Programming Surround View camera control unit

Labor time: 62 TU

Important Notice: Technical Bulletins issued by Porsche Cars North America, Inc. are intended only for use by professional automotive technicians who have attended Porsche service training
courses. They are written to inform those technicians of conditions that may occur on some Porsche vehicles, or to provide information that could assist in the proper servicing of a vehicle. Porsche special
tools may be necessary in order to perform certain operations identified in these bulletins. Use of tools and procedures other than those Porsche recommends in these bulletins may be detrimental to the
safe operation of your vehicle, and may endanger the people working on it. Properly trained Porsche technicians have the equipment, tools, safety instructions, and know-how to do the job properly and
safely. Part numbers listed in these bulletins are for reference only. The work procedures updated electronically in the Porsche PIWIS diagnostic and testing device take precedence and, in the event of a
discrepancy, the work procedures in the PIWIS Tester are the ones that must be followed.

© 2020 Porsche Cars North America, Inc.

Tequipment

Mar 4, 2020
Page 17 of 17