NHTSA ID Number: 10171932
Manufacturer Communication Number: 15-236-18R
TSB/Document Date: 2020-03-03
Summary
The following information addresses reprogramming file availability and a software update installation procedure to provide optimization to the new Harman Gen 3.1 Audio and Navigation head units utilized in the models as listed.
ATTENTION:
CLAIMS PERSONNEL q
IMPORTANT - All
Service Personnel
Should Read and
Initial in the boxes
provided, right.
SERVICE MANAGER
© 2018 Subaru
of America, Inc. All rights reserved.
GENERAL MANAGER q
PARTS MANAGER
q
q
SERVICE BULLETIN
APPLICABILITY: 2019-20MY Impreza
2019-20MY Crosstrek (Including Hybrid Model)
2019-20MY Forester
2019MY Legacy/ Outback
2019-20MY WRX
2019-20MY BRZ- Navigation -equipped ONLY
2019-20MY Ascent
SUBJECT:
NUMBER: 15-236-18R
DATE: 12/04/18
REVISED: 02/19/20
Reprogramming File Availability for Optimization of
Harman Gen 3.1 Audio and Navigation Head Units
INTRODUCTION:
The following information addresses reprogramming file availability and a software update
installation procedure to provide optimization to the new Harman Gen 3.1 Audio and Navigation
head units utilized in the models as listed above. The procedure will involve either downloading
the software update files from Subarunet (or using those sent directly from Nuspire) and transferring
them onto a flash drive for head unit installation. These files do NOT include Map Update data. It is
VERY IMPORTANT to read and understand this information completely to understand all changes
from prior releases before proceeding.
A time line chart along with a complete list of all the conditions addressed by this and previous
Harman 3.1 software updates is provided in “Appendix A” located at the end of this bulletin.
IMPORTANT NOTES:
•
If a vehicle presents with a current blank or black screen condition, request an exchange unit.
•
Be sure to locate and re-format any existing USB drives used for updating Harman audio
units in order to fully clear them before adding these new files to them.
•
On BRZ models, this update applicable to HIGH / Navigation-equipped head units only.
•
If a Map update is pending, please follow the instructions posted on Subarunet: Service
Operations & Technical > Forms/Downloads > Navigation System Map Updates and select
the applicable link.
CAUTION: VEHICLE SERVICING PERFORMED BY UNTRAINED PERSONS COULD
RESULT IN SERIOUS INJURY TO THOSE PERSONS OR TO OTHERS.
Subaru Service Bulletins are intended for use by professional technicians ONLY. They
are written to inform those technicians of conditions that may occur in some vehicles,
or to provide information that could assist in the proper servicing of the vehicle. Properly
trained technicians have the equipment, tools, safety instructions, and know-how to
do the job correctly and safely. If a condition is described, DO NOT assume that this
Service Bulletin applies to your vehicle, or that your vehicle will have that condition.
Subaru of America, Inc. is
ISO 14001 Compliant
ISO 14001 is the international standard for
excellence in Environmental Management
Systems. Please recycle or dispose of
automotive products in a manner that is friendly
to our environment and in accordance with all
local, state and federal laws and regulations.
Continued...
Bulletin Number: 15-236-18R; Revised: 02/19/20
Page 1 of 17
PRODUCTION CHANGE INFORMATION:
These updates (December 2019) apply to the models listed
above equipped with Harman Gen 3.1 Audio and Navigation
head units only.
The latest software version (including all available updates) was
incorporated into production per the starting VIN table to the
right:
Model
Starting VIN
Legacy
TBD
Outback
TBD
Impreza 4-Door
TBD
Impreza 5-Door
TBD
Crosstrek
TBD
BRZ*
TBD
Forester
TBD
Ascent
TBD
*HIGH / Navigation - equipped head units only
PART INFORMATION:
Multimedia System Type
Descriptive Features
6.5 Inch Display Audio System (Base)
No CD slot / Eject Button
6.5 Inch Display Audio System (Base +)
Equipped with CD Player and Eject Button
8.0 Inch Display Audio System (Mid)
Phone Button
8.0 Inch Audio / Navigation System (High)
Map Button but no Phone Button
Reference photos of each head unit faceplate are supplied below:
BASE +
Uses MID
update file
Continued...
Bulletin Number: 15-236-18R; Revised: 02/19/20
Page 2 of 17
Materials Required:
An empty, USB 2.0 or 3.0 storage device (flash drive) will be needed to perform the update
procedure. The device should be dedicated to storing and transferring these updating files only. It
must be a minimum of 16GB or more in size and contain a NTFS file format before downloading the
update files onto it.
IMPORTANT NOTES:
•
NEVER change the update file names after downloading them.
•
NEVER save any other files on the same flash drive.
There are various types of USB flash drive available from many suppliers. If the head unit does
NOT recognize the USB drive during the reprogramming process, due to Controller IC type of USB
drive or Compatibility with the head unit, clear the file and re-format the flash drive for “FAT32” as
outlined below in Step 2 instead of “NTFS”. If a recognition problem persists, use a USB flash drive
from another manufacturer.
Recommended Flash Drives:
•
Kingston®: Data Traveler G3, G4, SE9 or the Hyper-X Series
•
SanDisk®: Cruzer Series, Ultra Flair
•
Transcend®: JetFlash 300, 600 or 790
•
Verbatim®: Store ‘n’ Go
Continued...
Bulletin Number: 15-236-18R; Revised: 02/19/20
Page 3 of 17
SERVICE PROCEDURE / INFORMATION:
REMINDER: Customer satisfaction and retention starts with performing quality repairs.
Step 1- Software Version Confirmation From the HOME screen, touch “Settings”.
After starting the engine, from the HOME screen, touch “Settings”.
•
From the Settings screen, scroll down to and then touch “System Information”.
•
The currently installed software version will be displayed. If the Software Version is
Rel_UE 19.22.70 or Rel_UE 19.25.70 (or before), proceed to Step 2. This version number
is the same for all 4 levels of head unit.
VERY IMPORTANT: If the current version is Rel_UA 19.36.70 or Rel_UA.19.42.70, STOP as the
latest version has already been installed and no update is required at this time.
Continued...
Bulletin Number: 15-236-18R; Revised: 02/19/20
Page 4 of 17
STEP 2- Prepare the USB:
CAUTION: Do not use any USB flash drive which utilizes file organizing software or an operating
system.
VERY IMPORTANT: Before attempting to download any data files, confirm the PC and flash drive
being used is not infected with any virus. The flash drive MUST be formatted for NTFS .
•
Make sure the USB flash drive contains no
other files.
•
Right click on the corresponding
“Removable Disk”.
•
Select “Format”.
•
From the File System drop-down menu,
select “NTFS”
•
Check the “Quick Format” box (if not
already done).
•
Click on “Start” to format the USB flash
drive.
STEP 3- Download the Update Files to the USB:
VERY IMPORTANT: When updating a “Base +” head unit, the “MID” update files must be used.
The files are available for download on Subarunet (see “A” below).
The applicable reprogramming files have also been sent directly to retailers by Nuspire in the same
way a Select Monitor Update would be pushed out. (see “B” below).
Follow “A” when using files downloaded from Subarunet.
Follow “B” when using the files sent directly to the SDS notebook from Nuspire.
Continued...
Bulletin Number: 15-236-18R; Revised: 02/19/20
Page 5 of 17
“A” When using update files downloaded from Subarunet:
Click Here to Access the Downloads for Audio/Navigation Information on Subarunet
IMPORTANT: Files downloaded from Subarunet will be .zip files and must be unzipped before
they can be used. Using the normal audio / navigation system file update download procedure: Go
to Subarunet, select Service Operations and Technical>>Forms/Downloads>>Gen 3/Harman for
Audio/Navi then click on the applicable Hyperlink to download the file(s) to your SDS Notebook or
PC:
BASE- 2019-20 Impreza_Crosstrek_Crosstrek Hybrid & 2019 Legacy-Outback HARMAN AUDIO
UPDATE - DECEMBER 2019
BASE PLUS or MID - 2019-20 Impreza_Crosstrek Crosstrek Hybrid_Forester_Ascent & WRX - 2019
Legacy-Outback HARMAN AUDIO UPDATE - DECEMBER 2019
HIGH - 2019-20 Impreza_Crosstrek_Crosstrek Hybrid_BRZ_Forester_Ascent_WRX & 2019 LegacyOutback HARMAN AUDIO UPDATE - DECEMBER 2019
•
Go to Downloads.
•
CAUTION: After download is complete, NEVER change the file or folder names.
•
Once the files have been downloaded from Subarunet, click on the Downloads folder and then
sort by Date Modified to bring the most recent files to the top of the list.
•
Open / display the contents of File folder, for example (HIGH - 2019-20 Impreza_Crosstrek_
Crosstrek Hybrid_BRZ_Forester_Ascent_WRX & 2019 Legacy-Outback HARMAN AUDIO
UPDATE - DECEMBER 2019).
•
Click on “Extract All Files”.
•
From the dialog box, browse to My Documents then click on “Extract”.
•
Double-click on the required file (for this example, select the file entitled “HIGH - 2019-20
Impreza_Crosstrek_Crosstrek Hybrid_BRZ_Forester_Ascent_WRX & 2019 Legacy-Outback
HARMAN AUDIO UPDATE - DECEMBER 2019”).
•
Copy ONLY the “update” folder then paste (or click / drag) it to the “clean” USB flash drive
as listed (Removable Disk) in the directory.
•
To avoid confusion, label the flash drive with the file contents (e.g. BASE 3.1, BASE PLUS
or MID 3.1 or HIGH 3.1).
•
Go to Step 4.
Bulletin Number: 15-236-18R; Revised: 02/19/20
Continued...
Page 6 of 17
“B” When using update files sent directly from Nuspire:
•
Go to My Documents on the GUI screen to display the list of available update files shown
below.
•
CAUTION: After download is complete, NEVER change the file or folder names.
•
Sort by Date Modified to bring the most recent files to the top of the list. The folder is named:
_Harman Audio-Navi Update Files.
•
Double-click on the required file (for this example, select the file entitled “HIGH - 2019-20
Impreza_Crosstrek_Crosstrek Hybrid_BRZ_Forester_Ascent_WRX & 2019 Legacy-Outback
HARMAN AUDIO UPDATE - DECEMBER 2019”) and the update file will display as
shown.
•
Select the update folder and either copy / paste or click / drag it to the USB flash drive.
NOTE: Do not copy the entire “HIGH-20…” File folder. Copy ONLY the File folder named
“update” to the flash drive
•
Once the folder named “update” is loaded onto the USB flash drive, right click on the drive
and select “Eject”.
•
Remove the USB flash drive after the prompt appears that says “Safe to Remove Hardware”.
•
Mark the USB to indicate the head unit it will update (HIGH 3.1 in this example).
•
Repeat the above steps to create the BASE PLUS or MID 3.1 and HIGH 3.1 USB flash drives
as needed using a separate USB drive for each update folder.
STEP 4- IMPORTANT: Confirm the update folder on the USB flash drive is for the head unit being
reprogrammed ONLY. NEVER install multiple update folders onto the same flash drive at the same
time.
IMPORTANT REMINDER: When updating a “Base +” head unit, the “BASE PLUS or MID 3.1”
update files must be used.
Continued...
Bulletin Number: 15-236-18R; Revised: 02/19/20
Page 7 of 17
•
After confirmation, move to the car and either start the engine or follow the procedure as
outlined in document GR8-1100 on STIS for use of the GR8’s Power Supply Mode.
HIGH - 2019-20 Impreza_Crosstrek_Crosstrek Hybrid_BRZ_Forester_Ascent_WRX & 2019 Leg...
Copy ONLY the folder named “update” to the USB.
•
Never change the folder name from “update”.
•
Confirm there is only a folder named “update” on the flash drive.
CAUTION: Confirm one final time the head unit you are about to update matches the update file
selected. Attempting to install the incorrect update file will disable the head unit.
STEP 5- Update Installation:
IMPORTANT: Always record the customer’s radio station presets and navigation favorites (where
applicable) before proceeding further as they will most likely need to be reset once the update and
re-boot procedures are completed. In addition, some customizable system settings may need to be
reset as they may return to the default setting during the update.
•
With the engine idling (or GR8 connected), plug the flash drive into the USB Port.
IMPORTANT NOTE: If the head unit does not recognize the USB flash drive during the
reprogramming process, this may be due to an incompatible Controller IC in the USB flash drive or
it is otherwise incompatible with the head unit. If this occurs, delete all files from the flash drive and
re-format it to “FAT32”, instead of “NTFS” and reload the appropriate “update” folder to the USB
flash drive. If the USB flash drive is still not recognized, please discontinue the use of that drive and
instead use a USB flash drive from a different manufacturer.
Continued...
Bulletin Number: 15-236-18R; Revised: 02/19/20
Page 8 of 17
•
After the unit “authenticates” the USB flash drive, press “Next” and after the second screen is
displayed, press “Next” again.
NOTE: If an attempt is made to install the wrong “grade” file into the wrong grade head unit
(EXAMPLE: “Base” update file into a “Base Plus or Mid” or “High” head unit), the USB
Authentication error screen below will be displayed:
If the PDF is very large, it may not load in the preview below.
Some older TSBs had multiple PDFs — visit the NHTSA Website to view all PDFs.
If the TSB PDF does not show, download or view it on the NHTSA Website.
Click on the (+) Plus Sign
Then Click on Associated Document(s)
Search NHTSA Database for Recalls
Search NHTSA Database for Vehicle Investigations
View Latest Vehicle Investigations
Search NHTSA Database for Vehicle Complaints
View Latest Vehicle Complaints
TSB/Document ID: 15-236-18R
Replacement Service Bulletin Number:
MFR Communication Date: 2020-02-19
MFR Internal Campaign ID/Software Version:
Communication Type: Service Bulletin/Repair Instructions
NHTSA Components: ELECTRICAL SYSTEM
MFR Component System:
MFR Component Subsystem:
Previous TSB | Next TSB |
- [Notice] When you receive a used device, it may be a customer return resold by Amazon without inspection. You can exchange it for a new one through Amazon. As this situation is unavoidable, we sincerely apologize. For any issues, contacting us via Amazon's "Messages" is the best way. THINKSCAN 689BT Bidirectional Scan Tool Can Be Used Immediately After It is Turned On, Without Complicated Registration Process, Which is More Convenient & Quick.
- Full Bi-Directional Control & 3000+ Active Tests: Take control and test components like actuators, fuel injectors, relays, and cooling fans in real time. You’ll quickly see if the problem is in the part itself or the control module — saving you hours of guesswork and frustrating trial-and-error.
- Advanced ECU Coding Capabilities: Handle module matching and hidden feature activation with confidence. When you replace an ECU or want to customize settings, this obd2 scanner diagnostic bi directional tool gives you the professional-level capabilities you need without the dealership price tag.
- 34+ Useful Reset and Maintenance Functions: Complete everyday service tasks smoothly with a wide range of helpful reset and maintenance functions. Whether you’re keeping up with regular upkeep or tackling a specific job, this scanner makes maintenance simpler and less stressful for both DIYers and pros.
- Comprehensive Full System Diagnostics: Diagnose every major system — Engine, Transmission, ABS, SRS, TPMS, and more — all in one place. Finally stop wondering if you’re missing something important; get the full picture and clear codes with ease.
- Top Reasons to Choose the D7S OBD2 Scanner: XTOOL D7S car scan tool, an upgrade of XTOOL D7, offers comprehensive features for automotive technicians, workshops, and DIY enthusiasts 1. Upgraded Hardware: 2+64GB memory, rear camera, intuitive interface, foldable bracket 2. Complete Diagnostics: FCA
Autoauth, OE-level all system scan, 39+ maintenance services, 4K+ bidirectional, CANFD/DoIP protocol 3. Advanced Capabilities: ECU coding, PMI functions 4. Wide Compatibility: Support 10,000+ models, covering 99% vehicle brands 5. Multi-language: Available in 22+ languages, No IP Restrictions 6. 3-Year Updates: Save 300 bucks on software updates for the latest features and optimizations - 2026 Upgraded D7S Car Scanner Features: The newly 2026 D7S V2.0 scanner for car brings exciting features for advanced vehicle diagnostics and enhanced user experience 1. FCA AutoAuth: Now supports FCA SGW module for Chrysler, for Jeep, for Dodge (2018+), for Fiat (2017+), enabling faster vehicle communication without gateway restrictions 2. PMI (Offline ECU Programming): Allows for Ford, for Lincoln, and for Mazda ECU programming for new modules 3. Optimized Diagnostic Report 2.0: Personalized reports with logos and customer info for auto shops. Note: Compatibility varies by cars, please check before order
- Cost-effective ECU Coding Scan Tool for Specific Brands: Enhance your vehicle's performance with XTOOL D7S! This obd2 scanner all systems bidirectional offers advanced capabilities at an affordable price, supports online for BMW, for Benz and offline for BENZ, for MIT, along with PMI functions for Ford, for Mazda, and for Lincoln. Ideal for technicians and DIY enthusiasts, this automotive scanner diagnostic tool optimizes vehicle performance and enhances the driving experience. Note: Not for all cars and modules, please send car VIN to check the compatibility before purchase
- OE All System Diagnostic & 8 Pids Graphing: XTOOL D7S is a comprehensive all system bi directional obd2 scanner that delivers dealer-level diagnostics, completely controlling over your vehicle’s performance and health. This automotive scan tool can read and clear DTCs, view live data and ECU information, retrieve freeze frames, and perform active tests and full obd2 functions. This bi-directional scan tool can can identify your vehicle's make, model, and year information with just one click and show up to 8 PIDs live data with options for CSV viewing, playback, and recording for in-depth analysis. It is easy-to-use for both professionals and beginners, helping pinpoint issues efficiently
- 3 Years Software Update, Value for Money: With 3 years of software updates and 22+ languages(no IP restrictions), XTOOL D7S auto scanner code scanner ensures ongoing compatibility for the latest car models and improved diagnostic functions. This all system vehicle diagnostic scanner comes with a 30-day return policy and a 24-month repair for dependable performance. XTOOL are dedicated to your satisfaction, so enjoy seamless support and lifetime expert assistance. Should you encounter any issues or concerns, don’t hesitate to reach out XTOOL. D7S with newest update with 22 languages freely transfer without authorization, check details from setting-language or from XTOOL
- 🔥 Historical lowest pr-ice now on sa-le--hot se-lling.
- 【🎈𝗜𝗙𝟳𝟰𝟱 𝗽𝗲𝗿𝗳𝗼𝗿𝗺𝘀 𝟲 𝗲𝘀𝘀𝗲𝗻𝘁𝗶𝗮𝗹 𝗿𝗲𝘀𝗲𝘁 𝗳𝘂𝗻𝗰𝘁𝗶𝗼𝗻𝘀—𝗔𝗕𝗦 𝗕𝗹𝗲𝗲𝗱𝗶𝗻𝗴, 𝗢𝗶𝗹 𝗥𝗲𝘀𝗲𝘁, 𝗘𝗣𝗕, 𝗦𝗔𝗦, 𝗧𝗵𝗿𝗼𝘁𝘁𝗹𝗲 𝗥𝗲𝗹𝗲𝗮𝗿𝗻, 𝗮𝗻𝗱 𝗕𝗠𝗦—𝗽𝘂𝘁𝘁𝗶𝗻𝗴 𝗽𝗿𝗼𝗳𝗲𝘀𝘀𝗶𝗼𝗻𝗮𝗹-𝗴𝗿𝗮𝗱𝗲 𝗺𝗮𝗶𝗻𝘁𝗲𝗻𝗮𝗻𝗰𝗲 𝗯𝗮𝗰𝗸 𝗶𝗻 𝘆𝗼𝘂𝗿 𝗵𝗮𝗻𝗱𝘀.】Spongy brakes? Stuck oil light? Parking brake won't release? Off-center steering? Rough idle after battery disconnect? Draining battery? IF745 handles all with a few taps. One tool covers six dealer-level resets, saving hundreds in labor costs. ❗ NOTE: Does NOT support bidirectional control, coding, or programming.
- 【✨ 𝗜𝗙𝟳𝟰𝟱 𝗴𝗼𝗲𝘀 𝗯𝗲𝘆𝗼𝗻𝗱 𝗯𝗮𝘀𝗶𝗰 𝗰𝗼𝗱𝗲 𝗿𝗲𝗮𝗱𝗶𝗻𝗴 𝘄𝗶𝘁𝗵 𝟭𝟬 𝗶𝗻𝘁𝗲𝗴𝗿𝗮𝘁𝗲𝗱 𝗳𝘂𝗻𝗰𝘁𝗶𝗼𝗻𝘀—𝗗𝗧𝗖 𝗟𝗼𝗼𝗸𝘂𝗽, 𝗜/𝗠 𝗥𝗲𝗮𝗱𝗶𝗻𝗲𝘀𝘀, 𝗙𝗿𝗲𝗲𝘇𝗲 𝗙𝗿𝗮𝗺𝗲, 𝗟𝗶𝘃𝗲 𝗗𝗮𝘁𝗮, 𝗢𝟮𝗦, 𝗢𝗕𝗠, 𝗘𝗩𝗔𝗣, 𝗮𝗻𝗱 𝗺𝗼𝗿𝗲. 】Pulling a code tells you something is wrong. IF745 tells you what the code means, when the fault happened, and what data surrounds it. Pass emissions with one I/M Readiness tap. Freeze the fault moment with Freeze Frame. Monitor live sensor data in real time. Turn cryptic codes into clear answers.
- 【🛒 𝗜𝗙𝟳𝟰𝟱 𝗽𝗲𝗿𝗳𝗼𝗿𝗺𝘀 𝗳𝘂𝗹𝗹-𝘀𝘆𝘀𝘁𝗲𝗺 𝗱𝗶𝗮𝗴𝗻𝗼𝘀𝘁𝗶𝗰𝘀 𝗮𝗰𝗿𝗼𝘀𝘀 𝗮𝗹𝗹 𝗺𝗼𝗱𝘂𝗹𝗲𝘀—𝗲𝗻𝗴𝗶𝗻𝗲, 𝗔𝗕𝗦, 𝗮𝗶𝗿𝗯𝗮𝗴, 𝘁𝗿𝗮𝗻𝘀𝗺𝗶𝘀𝘀𝗶𝗼𝗻, 𝘀𝘁𝗲𝗲𝗿𝗶𝗻𝗴, 𝘀𝘂𝘀𝗽𝗲𝗻𝘀𝗶𝗼𝗻, 𝗯𝗼𝗱𝘆 𝗲𝗹𝗲𝗰𝘁𝗿𝗼𝗻𝗶𝗰𝘀, 𝗮𝗻𝗱 𝗺𝗼𝗿𝗲. 】Warning lights on but you don't know why? Skip the $100+ diagnostic fee at the shop. Run a complete self-check from your driveway. IF745 reads and clears fault codes, retrieves ECU info, and displays live data from every accessible module—delivering a full vehicle health report in minutes, without leaving home.
- 【✅𝗜𝗙𝟳𝟰𝟱 𝗳𝗲𝗮𝘁𝘂𝗿𝗲𝘀 𝗮 𝟳-𝗶𝗻𝗰𝗵 𝗱𝗶𝘀𝗽𝗹𝗮𝘆, 𝗲𝗿𝗴𝗼𝗻𝗼𝗺𝗶𝗰 𝗱𝗲𝘀𝗶𝗴𝗻, 𝗪𝗶-𝗙𝗶 𝘂𝗽𝗱𝗮𝘁𝗲𝘀, 𝗮𝗻𝗱 𝘇𝗲𝗿𝗼 𝘀𝘂𝗯𝘀𝗰𝗿𝗶𝗽𝘁𝗶𝗼𝗻 𝗳𝗲𝗲𝘀 𝗳𝗼𝗿 𝗵𝗮𝘀𝘀𝗹𝗲-𝗳𝗿𝗲𝗲 𝗱𝗶𝗮𝗴𝗻𝗼𝘀𝘁𝗶𝗰𝘀.】Large screen means no squinting. Intuitive navigation and customizable data displays put key info at your fingertips. Wi-Fi delivers lifetime free updates without a computer. No recurring fees. No hidden costs. Just a reliable tool that works as hard as you do.
This product presentation was made with AAWP plugin.