GROUP
AUTOMATIC
TRANSMISSION
DATE

Technical Service Bulletin
AUGUST 2019

SUBJECT:

NUMBER
19-AT-015H
MODEL
Accent (RB), Azera (TG/HG),
Elantra (UD/MD/GD/JK),
Santa Fe (CM/AN/NC), Sonata
(YF/YF HEV, LF/LF HEV/PHEV),
Tucson (LM/TL 2.0L), Veloster
Turbo (FS)

AUTOMATIC TRANSAXLE SOLENOID DTC P0741, P0743,
P0748, P0753, P0758, P0763, P0768, P0773 & P2709

This TSB supersedes 15-AT-010 to add additional models.
Description: If you are servicing an applicable vehicle with a “Check Engine” light on and one
or more of the DTC listed below, follow the repair procedure and replace the related solenoid
and oil pressure harness.
NOTE: The 6-speed vehicles listed below are equipped with a Generation1 valve body with 8
solenoids. Newer 6-speed transmissions have a Generation2 valve body with 7 solenoids
(Refer to TSB 19-AT-016H).

Applicable Vehicles:
2012~17
2011
2012~17
2011~16
2013~17
2013~14
2010~12
2013~18
2013~16
2011~14
2015~19
2011~15
2016~19
2016~19
2010~15
2016~
2013~15

Accent (RB)
Azera (TG)
Azera (HG)
Elantra (MD/UD)
Elantra GT (GD)
Elantra Coupe (JK)
Santa Fe (CM)
Santa Fe (AN) 2.0L
Santa Fe (AN) 2.4L
Sonata (YF)
Sonata (LF)
Sonata Hybrid (YF HEV)
Sonata Hybrid (LF HEV)
Sonata Plug-in Hybrid (LF PHEV)
Tucson (LM)
Tucson (TL) 2.0L
Veloster (FS) 1.6T

Circulate To: Service Manager, Warranty Manager, Service Advisors, Technicians, Fleet Repair

ATM SOLENOID DTC P0741, P0743, P0748, P0753,
P0758, P0763, P0768, P0773, P1778 & P2709

SUBJECT:

Parts Information:
Refer to the PNC in the parts catalog to order the correct solenoid part number.
Model

2012~17
2011
2012~17
2011~16
2013~17
2013~14
2010~12
2013~18
2013~16
2011~14
2015~19
2011~15
2011~19
2010~15
2016~
2013~15

Accent (RB)
Azera (TG)
Azera (HG)
Elantra (MD/UD)
Elantra GT (GD)
Elantra Coupe (JK)
Santa Fe (CM)
Santa Fe (AN) 2.0L
Santa Fe (AN) 2.4L
Sonata (YF)
Sonata (LF)
Sonata Hybrid (YF HEV)
Sonata Hybrid(LF HEV/PHEV)
Tucson (LM)
Tucson (TL) 2.0L
Veloster (FS) 1.6T

Part

PNC

Part Number

Torque converter solenoid
(T/C)

46202A

46313-3B***

46313C

46313-3B***

Engine clutch solenoid (HEV)

46313C

46313-3B***

Shift solenoid C (35R)

46313B

46313-3B***

Shift solenoid B (26-B)

46313C

46313-3B***

Shift solenoid A (UD)

46313B

46313-3B***

Shift solenoid D (OD)

46313B

46313-3B***

Shift solenoid F (SS-B)

46313D

46313-3B***

Shift solenoid E (SS-A)

46313D

46313-3B***

Pressure control solenoid
(P/C)

46313A

46313-3B***

Valve body internal harness

46307

46307-3B***

45282E

45282-2****
45283-3B***
45283-3D***
45283-3F***

Plastic oil pan gasket

TSB #: 19-AT-015H

Page 2 of 11

ATM SOLENOID DTC P0741, P0743, P0748,,P0753,
P0758, P0763, P0768, P0773, P1778 & P2709

SUBJECT:

Warranty Information:
Model

OP Code

Operation

2012~17
2011
2012~17
2011~16
2013~17
2013~14
2010~12
2013~18
2013~16
2011~14
2015~19
2011~15
2016~19
2016~19
2010~15
2016~
2013~15

Accent (RB)
Azera (TG)
Azera (HG)
Elantra (MD/UD)
Elantra GT (GD)
Elantra Coupe (JK)
Santa Fe (CM)
Santa Fe (AN) 2.0L
Santa Fe (AN) 2.4L
Sonata (YF)
Sonata (LF)
Sonata Hybrid (YF HEV)
Sonata Hybrid (LF HEV)
Sonata Plug-in Hybrid (LF HEV)
Tucson (LM)
Tucson (TL) 2.0L
Veloster (FS) 1.6T

45775R00

2011~15
2016~19

Sonata Hybrid (YF HEV)
Sonata Hybrid (LF HEV/PHEV)

45775RH1 Additional

All

TSB #: 19-AT-015H

45775RQ0

OP Time

Causal
Part

Replace
solenoid
valve and
Refer to
Refer to
valve
WEBLTS
Parts
body
for
Informaharness
current
tion table
LTS time on Page 2

Nature Cause
Code Code

T74

ZZ3

GDS

Page 3 of 11

SUBJECT:

ATM SOLENOID DTC P0741, P0743, P0748, P0753,
P0758, P0763, P0768, P0773, P1778 & P2709

Service Procedure:
1.

Attach a GDS and select DTC Analysis and A/T menu. Record the DTC and description.
Delete the DTC.

2.

From the GDS home screen, select Data Analysis and A/T menu and the solenoid parameters
shown below. If the solenoids show:
 Continuous and changing output while driving, the wiring currently has no open/short
circuits. Go to Step 4.
 No continuous and changing output, go to Step 3.

3.

Visually check the wiring harness between the PCM and transmission for a damaged wire or
open/short circuit. Check for a damaged pin or pin not fully inserted into the connector.
 If damage exists, repair or replace the control wiring and drive the vehicle to confirm the
repair.
 If no damage or open/short circuit, go to Step 4.

TSB #: 19-AT-015H

Page 4 of 11

ATM SOLENOID DTC P0741, P0743, P0748,,P0753,
P0758, P0763, P0768, P0773, P1778 & P2709

SUBJECT:

4.

Refer to the DTC recorded in Step 1 and follow the repair procedure shown below:
P0741
P1778
P0743
P0763
P0758
P0753
P0768
P2709
P0773
P0748

DTC
Torque converter clutch system
Engine clutch solenoid (HEV)
Torque converter (T/C)
Shift solenoid C (35R)
Shift solenoid B (26-B)
Shift solenoid A (UD)
Shift solenoid D (OD)
Shift solenoid F (SS-B)
Shift solenoid E (SS-A)
Pressure control solenoid (P/C)

Repair Procedure
Replace the T/C solenoid if no other DTC found.

Go to Step 5 and replace the related solenoid and
valve body harness

5.

Record the preset radio stations.
Remove the battery and battery tray.

6.

Remove the undercover below the transmission.

7.

Drain the radiator and remove the lower radiator hose from the radiator, if necessary.
Drain the ATF.

8.

Use a screwdriver to release the tab and
remove the solenoid connector on top of the
case.
Remove the bolt that secures the connector
and push the connector into the transmission.
Disconnect the vent hose on the top of the oil
pan.

9.

Remove the oil pan bolts and remove the pan.

CAUTION
Use rubber hammer to tap the oil pan
cover on a corner until the cover is
loose.

TSB #: 19-AT-015H

Page 5 of 11

SUBJECT:

ATM SOLENOID DTC P0741, P0743, P0748, P0753,
P0758, P0763, P0768, P0773, P1778 & P2709

10. Use a small screwdriver to pry the connector
from the oil temperature sensor (except for
transmissions with integrated temperature
sensor and harness).

11. Remove three bolts to the solenoid valve
connector.

12. Pull the solenoid connector outward and move
the connector out of position.

TSB #: 19-AT-015H

Page 6 of 11

ATM SOLENOID DTC P0741, P0743, P0748,,P0753,
P0758, P0763, P0768, P0773, P1778 & P2709

SUBJECT:

13. Remove the bolt that secures the detent spring
and remove the spring.
Torque: 8~11 lb.ft (1.2~1.5 kgf.m/10~13 N.m)

14. Remove the valve body bolts in the order
shown and remove the valve body.

CAUTION
Place the valve body on a clean paper
towel. Placing the valve body on a rag
may cause lint to enter the valve body.

15. Use a screwdriver to depress the locking tab
and pull outward on the connector to the input
and output speed sensor.

TSB #: 19-AT-015H

Page 7 of 11

SUBJECT:

ATM SOLENOID DTC P0741, P0743, P0748, P0753,
P0758, P0763, P0768, P0773, P1778 & P2709

16. Remove two bolts that secure the valve body
harness to the case.
Pull the connector downward out of the case.
Install a new harness and insert the connector
into the case. Attach the retainer and bolt on
top of the case as shown in Step 9.
Install the bolts that secure the harness.
Torque: 7~9 lb.ft (1.0~1.2 kgf.m/10~12 N.m)

17. Use a 5mm hex socket and remove 9 Allen
bolts that secure the solenoid support.
Remove the solenoid support.

18. Refer to the DTC recorded in Step 1 and
replace the related solenoid.
DTC
P0741 T/C
P0743 T/C
P1778 T/C
P0763 35R
P0758 26B
P0753 UD
P0768 OD
P2709 SS-B
P0773 SS-A
P0748 P/C

Solenoid
TC solenoid (T/C)
TC solenoid (T/C)
Engine clutch solenoid (HEV)
Shift solenoid C (35R)
Shift solenoid B (26-B)
Shift solenoid A (UD)
Shift solenoid D (OD)
Shift solenoid F (SS-B)
Shift solenoid E(SS-A)
Pressure Control solenoid

Reinstall the solenoid support.

TSB #: 19-AT-015H

Page 8 of 11

SUBJECT:

ATM SOLENOID DTC P0741, P0743, P0748,,P0753,
P0758, P0763, P0768, P0773, P1778 & P2709

19. Confirm the O-rings are installed correctly in
the case.
Reconnect the input and output speed sensor
connector to the harness (see Step 15).

20. Align the manual shaft to the shift lever and
install the valve body.

21. Install the valve body bolts and torque the bolts
to specification in the order shown.
Torque: 7~9 lb.ft (1.0~1.2 kgf.m/10~12 N.m)
Reinstall the bolt and detent spring.
Torque: 8~11 lb.ft (1.2~1.5 kgf.m/10~13 N.m)

TSB #: 19-AT-015H

Page 9 of 11

SUBJECT:

ATM SOLENOID DTC P0741, P0743, P0748, P0753,
P0758, P0763, P0768, P0773, P1778 & P2709

22. Reconnect the solenoid harness to the
solenoids and oil temperature sensor.
Install the bolts to the solenoid harness
connector and torque to specification.
Torque: 7~9 lb.ft (1.0~1.2 kgf.m/10~12 N.m)

23. PLASTIC OIL PAN:
Install a new gasket to the oil pan, reinstall the
pan and tighten the bolts to specification.
Torque: 6~7 lb.ft (0.9~1.0 kgf.m/8~9 N.m)

STEEL OIL PAN:
Use RTV Silicon Gray, P/N 00232-19061 and
a small caulking gun, P/N 00232-19064, or
equivalent and apply sealant to the oil pan.
Reinstall the pan.
Torque: 9~11 lb.ft (1.3~1.5 kgf.m/12~15 N.m)

24. Attach the lower radiator hose. Add ethylene glycol engine coolant to the radiator and check the
level according to the appropriate shop manual, “Engine” Section.
25. Reconnect the battery.
Input the radio stations recorded in Step 5.

TSB #: 19-AT-015H

Page 10 of 11

ATM SOLENOID DTC P0741, P0743, P0748,,P0753,
P0758, P0763, P0768, P0773, P1778 & P2709

SUBJECT:

26. Remove the transaxle fill plug.
Use a funnel to add approximately 5~6 quarts
of SP-IV ATF through the fill plug opening.
Reinstall the fill plug.
Attach the GDS to the DLC and select Data
Analysis, A/T menu and Oil Temperature
Sensor.
Start the engine and shift to Park. When the
ATF is 122°F~140°F (50~60°C), remove the
level checking plug. The level is correct when
oil flows out of the level checking plug in a thin
steady stream.
Collect and dispose of any excess fluid in
accordance with local regulations.
27.

Clear the DTC and test drive the vehicle for two key-on/key-off driving cycles, including 12-3-4-5-6 upshifts and 6-5-4-3-2-1 downshifts. If the DTC returns, perform the following
repairs.
DTC
P0741
P0743
P1778
P0753
P0758 
P0763
P0768
P0773 .
P2709
P0741
P0748

Repair Procedure
Replace the transmission

Replace the control wiring harness between the PCM and transmission.
 If the solenoid DTC does not return, return the vehicle to the customer.
 If the solenoid DTC returns again, replace the PCM.

28. Clear the DTC in the Blue Link system per instructions of TSB 12-BE-005-2.
29. Drive the vehicle to confirm the transmission is operating as designed.

TSB #: 19-AT-015H

Page 11 of 11