Rev.00

The information and procedures published below are strictly confidential and intended exclusively for authorized operators and individuals. All copyrights are the property of Automobili Lamborghini S.p.A based on copyright law. The company reserves the right to make
updates and modifications. The reprinting, reproduction, forwarding to unauthorized people and/or to third parties and partial or entire
translation thereof are prohibited without written authorization from Automobili Lamborghini S.p.A.
doc. nr: L/V6_M06 Rev.[06]

6/12

L73XA.09.19

To:
Subject:
Date:
Pages

Official After Sales Network
Pydos ECU replacement and instrument cluster update
06 September 2019
12

NOTE:

NOTE:

If previously the value read was expressed in miles
before proceed please convert the value into kilometers. The next service must be entered in km.
Clicking the “Adopt” button it is possible to check if
the value updates correctly, both from the instrument
cluster and from the “Value” field of the Odis Service
dialogue screen.

After clicking the “Adopt” button it is possible to
check if the value updates correctly, both from the
instrument cluster and from the “Value” field of the
Odis Service dialogue screen.

23. Enter "54" in the text box at the top right and click on
"Select Channel" to select the channel to set the remaining days to the next service.

The configuration of the expiration date of the Pydos control unit is necessary for all the vehicles involved in this
campaign.

V.

Configuration of the expiration date of the Pydos
control unit

25. From the guided function of the control unit 17 select
the function “17 - Pydos ECU replacement” and click
“Execute”.

24. In the "Input" box, enter the days read from the instrument cluster and previously annotated. To the next
service (E.g. 365 = 365 days) and click on "Apply".

26. Click the “Done/Continue” button to continue.

Rev.00

The information and procedures published below are strictly confidential and intended exclusively for authorized operators and individuals. All copyrights are the property of Automobili Lamborghini S.p.A based on copyright law. The company reserves the right to make
updates and modifications. The reprinting, reproduction, forwarding to unauthorized people and/or to third parties and partial or entire
translation thereof are prohibited without written authorization from Automobili Lamborghini S.p.A.
doc. nr: L/V6_M06 Rev.[06]

7/12

L73XA.09.19

To:
Subject:
Date:
Pages

Official After Sales Network
Pydos ECU replacement and instrument cluster update
06 September 2019
12
28. Click on "-1-" (Yes) and proceed with the manual procedure.

27. Click the button -2- and perform the manual operation.
29. Check the date and time of the instrument cluster.
Click on "Yes" if the date and time of the instrument
cluster are correct, otherwise click "No" and set the
correct values as described in the car's use and
maintenance manual.

NOTE:
The expiry of the Pydos battery must be set according to
the production year of the Pydos control unit fitted in the
car and previously annotated. Refer to the following image
to identify the position of the production data label.

Rev.00

30. Click the “Done/Continue” button to initialize the
expiration of the Pydos battery.

The information and procedures published below are strictly confidential and intended exclusively for authorized operators and individuals. All copyrights are the property of Automobili Lamborghini S.p.A based on copyright law. The company reserves the right to make
updates and modifications. The reprinting, reproduction, forwarding to unauthorized people and/or to third parties and partial or entire
translation thereof are prohibited without written authorization from Automobili Lamborghini S.p.A.
doc. nr: L/V6_M06 Rev.[06]

8/12

L73XA.09.19

To:
Subject:
Date:
Pages

Official After Sales Network
Pydos ECU replacement and instrument cluster update
06 September 2019
12

31. Check the production date indicated on the label of the
Pydos control unit and insert it in the appropriate field
on the ODIS screen, then click on "Adopt".

VI.

NOTE:
The format of the date to be inserted is the one shown in
the example, and require to input only the year, e.g.
"2018".
32. Click on "Yes" if the inserted date is correct, "No" to
interrupt the procedure.

Erase fault memories:

34. Once the previous steps has been completed, go back
to the tab “Special Functions” and select “Erase fault
memory – overall system” to clear all the faults stored.
The complete guide in order to erase all fault memories is available in the workshop manual, chapter
10.00.B: Deleting the data in the fault memory of
control units.
/* Diagnosis protocol saving */
At the end of the procedure, save the diagnostic protocol
as described in chapter 10.00.ODIS Saving the diagnostic
protocol.

IMPORTANT:
The diagnosis protocol has to be attached to the related
Warranty Claim (in order to insert the claim on the Web
Portal, please refer to Warranty Claim Manual you can
find under the Portal, Warranty section).
33. The number of days for the Pydos battery validity is
displayed. Click "Done/Continue" to complete the
Pydos battery life setting procedure.

Rev.00

The information and procedures published below are strictly confidential and intended exclusively for authorized operators and individuals. All copyrights are the property of Automobili Lamborghini S.p.A based on copyright law. The company reserves the right to make
updates and modifications. The reprinting, reproduction, forwarding to unauthorized people and/or to third parties and partial or entire
translation thereof are prohibited without written authorization from Automobili Lamborghini S.p.A.
doc. nr: L/V6_M06 Rev.[06]

9/12

To:
Subject:
Date:
Pages

L73XA.09.19

Official After Sales Network
Pydos ECU replacement and instrument cluster update
06 September 2019
12

/* Trouble shooting */
i.

If the following error page is shown, you shall
abort the procedure clicking on “Cancel Test” and
contact the Technical Support.

ii.

If the error message regarding the VAS5054 interface and the two icons for status of on board connection and key ON are shown as in the picture
below:
-

iii.

If one of the connection error screens is shown as
in the pictures below:
-

Rev.00

Click “Cancel”;
Repeat the VAS5054 HW interface installation following the procedure (*) “VCI Manager v2.0”, by entering in the menu “Extras” on
the right side and clicking on “Diagnostic interface”.

it is not possible to establish a connection with
the central server. Please check carefully that
the diagnosis laptop is properly connected to
the internet network and retry clicking “Yes”
or “Done/Continue”.

iv.

If the loss of connection happens during the target/actual comparison during SVM procedure:
-

v.

It is not possible to connect to central server,
check the working connection of internet and
retry by clicking “1”.

If the incorrect identification message is shown as
in the picture below (error code: ODS1007E):
-

be sure that your Geko account is valid;

The information and procedures published below are strictly confidential and intended exclusively for authorized operators and individuals. All copyrights are the property of Automobili Lamborghini S.p.A based on copyright law. The company reserves the right to make
updates and modifications. The reprinting, reproduction, forwarding to unauthorized people and/or to third parties and partial or entire
translation thereof are prohibited without written authorization from Automobili Lamborghini S.p.A.
doc. nr: L/V6_M06 Rev.[06]

10/12

To:
Subject:
Date:
Pages

L73XA.09.19

-

-

Official After Sales Network
Pydos ECU replacement and instrument cluster update
06 September 2019
12

be sure that the label “Geko” is written on
the token that you are using for the authentication;
be sure the Password inserted is correct;
click on Cancel and perform the application test (see document
“ODIS_Checking_ConnectionServer_SV
M_2.0” (*)).

-

-

re-Start ODIS Service under following conditions:
1. Network connection available;
2. ODIS connection set on “Internet”;
Retry the application test and the SVM with
your GeKO Token.

IMPORTANT REMARK:
In the case an error is still present, retry the procedure with
a second GeKO token, if available.

vi.

If the infrastructure error message is shown as in
the picture below (error code: ODS9212E):
-

-

be sure that your Geko account is valid
be sure that the label “Geko” is written on the
token that you are using for the authentication
verify in ODIS settings you have “Internet”
instead
of
“CPN”
(see
document
“ODIS_Initial_Setup_2.0” (*))
click on Cancel and perform the application
test (see document
“ODIS_Checking_ConnectionServer_SVM_2
.0” (*))

vii.

In the case the flash container is not detected (see
figure):
-

-

Make sure to be recently synchronized with
Mirrorserver by checking the last date of Sync
under:
http://mirrorserver/maintenance/diagnosis.py
or under
http://[IP_address]/maintenance/diagnosis.py
if you don’t have previously defined the “mirrorserver” IP address alias.
Make sure to be correctly connected with Mirrorserver.

If the same error is present during the application
test, try the following procedure:
-

-

Rev.00

quit ODIS;
Enter
the
folder
C:\Program
Files
(x86)\Offboard_Diagnostic_Information_Syst
em_Service\.automatic_sessions on your diagnosis laptop;
delete the only file present in that folder.
The information and procedures published below are strictly confidential and intended exclusively for authorized operators and individuals. All copyrights are the property of Automobili Lamborghini S.p.A based on copyright law. The company reserves the right to make
updates and modifications. The reprinting, reproduction, forwarding to unauthorized people and/or to third parties and partial or entire
translation thereof are prohibited without written authorization from Automobili Lamborghini S.p.A.
doc. nr: L/V6_M06 Rev.[06]

11/12

L73XA.09.19

viii.

To:
Subject:
Date:
Pages

Official After Sales Network
Pydos ECU replacement and instrument cluster update
06 September 2019
12

If an error occurs during the SVM calibration
phase on the channel “55”, please perform the following actions.

Enter in the "Input" box the value “0” and click on
the “Apply” button to set the entered value.

Select “Self-diagnosis” from the “Operating
modes”.

After this operation switch back to “Diagnosis”
from the “Operating modes” and execute again the
SVM declared at the step 10.
Select the dashboard control unit, ECU 17 and
from the drop-down menu select “Adaption”, then
click on the green arrow to start the function.
NOTE:
ODIS technical documentation can be retrieved on the
Lamborghini web portal, under ODIS section.

IMPORTANT REMARK:
The documents to be mandatory attached to the claim
are:

Enter "55" in the text box at the top right and click
on "Select Channel" to access to the channel.

-

Job order done;

-

Diagnosis Protocol saved.

Failure to follow the procedures may lead to the rejection of the request.
Your Area Manager is at full disposal for further information

Rev.00

The information and procedures published below are strictly confidential and intended exclusively for authorized operators and individuals. All copyrights are the property of Automobili Lamborghini S.p.A based on copyright law. The company reserves the right to make
updates and modifications. The reprinting, reproduction, forwarding to unauthorized people and/or to third parties and partial or entire
translation thereof are prohibited without written authorization from Automobili Lamborghini S.p.A.
doc. nr: L/V6_M06 Rev.[06]

12/12