To:
Subject:
Date:
Pages

L636A.08.19

Official After-Sales Network
Gateway ECU connectivity configuration
02 September 2019
33

Campaign code:
L636-A.08.19.
Campaign Name:
Gateway ECU connectivity configuration.
Model:
Urus.
Model year:
MY 2019
Special or limited editions:
All versions
Markets:
Australia, Hong Kong, Malaysia, New Zealand, Singapore, Taiwan, Turkey.
VIN identification:

N.B.
Procedure A will be available only when the instructions require a preliminary check to be performed to
determine whether or not the vehicle actually needs
updating.
Network information notice.
As a result of continuous product monitoring, Automobili Lamborghini S.p.A. has detected that in some
markets a warning messege about missing data connection may appear on the infotainment display.
Solutions for the network:
Replacement and update of the gateway ECU configuration.

From KLA00282 to KLA01676

Important: before proceeding with the repair, connect to the warranty portal and use VIN Info to check
that:


The vehicle is actually affected by the instructions given in this bulletin; some vehicles may
not be, even when their VIN is included.



Procedures are identified by a letter (e.g. A, B
or C….etc., whose differences will be explained later in this bulletin); make sure that
the spare parts corresponding to the assigned
procedure are used.
Example

IMPORTANT:
Before carrying out the campaign in question, ensure that
the campaigns “L636A0418” and “L636A0419” have
been performed on the vehicle. In the event that it has not
been performed and is in the “VIN identification” list,
first carry out the campaigns “L636A0418”
and“L636A0419”, and then the campaign “L636A0819”.

Replacement parts:
IMPORTANT!

When the VIN is entered in the LIASS system, the
specific operation to be performed on that vehicle
will be specified. On the basis of the operation displayed on LIASS, please order one of the following
codes associated with the operations concerned,
where suggested:
Operation B, C, F: 4ML998049
Operation D, E, G: 4ML998049A

Rev.00

This document and its contents are strictly confidential and private and are provided for informational purposes only and may not be copied, recorded, transmitted, further distributed to any other subject, or published, in whole or in part, by any means or in any form and for
any purpose, without the prior written authorization of Automobili Lamborghini S.p.A. All copyrights are the property of Automobili
Lamborghini S.p.A based on the applicable laws. The company reserves the right to make updates and modifications
doc. no.: L/V6_M06 Rev.[06]

1/33

To:
Subject:
Date:
Pages

L636A.08.19

P/N Kit

Official After-Sales Network
Gateway ECU connectivity configuration
02 September 2019
33

Description

Q

The kit contains:
- GW control unit; P/N: 4N1907468AA
- Clamp; P/N: 4ML971141
- Clamp; P/N: 4ML971141A
- Connector sponge; P/N: 191971790A
- Connector sponge; P/N: 3B0971790
- Clamps; P/N: 893971850C
- GW control unit bracket; P/N: 4M0907347

4ML998049

1

borghini Portal and follow the “Campaigns” entry instructions in the W.Claim manual which can be
downloaded from the Portal.
Select the required campaign and proceed with entry,
carefully reading the options present in the alert displayed by the system (see example) and select the option performed on the vehicle.

The kit contains:

4ML998049A

- GW control unit; P/N: 4N2907468AA
- Clamp; P/N: 4ML971141
- Clamp; P/N: 4ML971141A
- Connector sponge; P/N: 191971790A

1

- Connector sponge; P/N: 3B0971790
- Clamps; P/N: 893971850C
- GW control unit bracket; P/N: 4M0907347

Depending on the option performed, the reimbursement will be structured in the following manner:
-

Operation B: Replacement of the Gateway
ECU WITHOUT SD-Creator download. Operations to perform: I, II, III, IV, V, VI, VII.
Labor: 5 hours
Spare Parts: 4ML998049

-

Operation C: Replacement of the Gateway
ECU WITH SD-Creator download. Procedures to perform: I, II, III, IV, V, V.A, VI, VII.
Labor: 5.5 hours
Spare Parts: 4ML998049

-

Operazione D: Replacement of the Gateway
ECU WITHOUT SD-Creator download. Procedures to perform I, II, III, IV, V, VI, VII.
Labor: 5 hours
Spare Parts: 4ML998049A

-

Operation E: Replacement of the Gateway
ECU WITH SD-Creator download.Procedures
to perform: I, II, III, IV, V, V.A, VI, VII.
Labor: 5.5 hours
Spare Parts: 4ML998049A

-

Operation F: Gateway ECU replacement.
Procedures to perform: III.
Labor: 1.3 hours

Management of replaced parts:
Store the parts removed from the vehicle in a suitable
manner, marked with their barcode for identification
during visits by the competent Area Manager.
Labor:
- Operation B: 5 hours
-

Operation C: 5.5 hours

-

Operation D: 5. hours

-

Operation E: 5.5 hours

-

Operation F: 1.3 hours

-

Operation G: 1.3 hours

Bulletins superseded:
None.
Warranty instructions:

To request reimbursement for the corrective action
performed, access the Warranties section of the Lam-

Rev.00

This document and its contents are strictly confidential and private and are provided for informational purposes only and may not be copied, recorded, transmitted, further distributed to any other subject, or published, in whole or in part, by any means or in any form and for
any purpose, without the prior written authorization of Automobili Lamborghini S.p.A. All copyrights are the property of Automobili
Lamborghini S.p.A based on the applicable laws. The company reserves the right to make updates and modifications
doc. no.: L/V6_M06 Rev.[06]

2/33

To:
Subject:
Date:
Pages

L636A.08.19

Official After-Sales Network
Gateway ECU connectivity configuration
02 September 2019
33

Spare Parts: 4ML998049

-

Operation G: Gateway ECU replacement.
Procedures to perform: III.
Labor: 1.3 hours
Spare Parts: 4ML998049A

Tools/Materials required
Code
Description.

Q

IMPORTANT:

Before following the instructions in the service campaign, the SD-Creator program must be installed.
The SD Creator installation instructions are contained in the bulletin: “BI.09.17_[ENG]_SD-Creator
installation package procedure”.

NOTE:
Operations B, C, D, E, F, G identify the labor times
and do not relate to the operations described in the
Work Instructions (I, II, III, IV, V, V.A, VI,VII).

WARNING!
Attach all documents generated during the work carried out as evidence of the work itself, for instance
workshop orders, diagnostic protocols etc. If one or
more of these is missing it may lead to a rejected reimbursement request.
Fill out the Service and Recall Campaign section in
the warranty booklet, which is shown in the figure below.

Rev.00

This document and its contents are strictly confidential and private and are provided for informational purposes only and may not be copied, recorded, transmitted, further distributed to any other subject, or published, in whole or in part, by any means or in any form and for
any purpose, without the prior written authorization of Automobili Lamborghini S.p.A. All copyrights are the property of Automobili
Lamborghini S.p.A based on the applicable laws. The company reserves the right to make updates and modifications
doc. no.: L/V6_M06 Rev.[06]

3/33

L636A.08.19

To:
Subject:
Date:
Pages

Official After-Sales Network
Gateway ECU connectivity configuration
02 September 2019
33

Preliminary operations:
1. Ensure you have recently synced with the Mirror
server by checking the last synchronization date:
http://mirrorserver/maintenance/diagnosis.py
or by directly entering the Btac-box IP address:
http://[IP_address]/maintenance/diagnosis.py

NOTE:
The instructions contained in this bulletin are based on the
ODIS diagnosis software updated to version 5.1.5 and the
Lamborghini 2.19.0 or later database (refer to information
bulletin BI.13.19 and make sure that ODIS Service is
properly updated on the laptop).

if you have not previously set the IP alias of the
mirror server.
(e.g.
http://12.34.567.890/maintenance/diagnosis.py)

IMPORTANT:
Make sure that the last synchronization was performed after Wednesday, June 19, 2019.

Rev.00

2. It is essential that you connect an appropriate battery charger to the charge points available in the
engine hood (left side of the vehicle). Please refer
to the following figure.

This document and its contents are strictly confidential and private and are provided for informational purposes only and may not be copied, recorded, transmitted, further distributed to any other subject, or published, in whole or in part, by any means or in any form and for
any purpose, without the prior written authorization of Automobili Lamborghini S.p.A. All copyrights are the property of Automobili
Lamborghini S.p.A based on the applicable laws. The company reserves the right to make updates and modifications
doc. no.: L/V6_M06 Rev.[06]

4/33

L636A.08.19

To:
Subject:
Date:
Pages

Official After-Sales Network
Gateway ECU connectivity configuration
02 September 2019
33

Work instructions:
The updating procedure described here includes the
following steps:
I.

Control unit 15 update;

II.

Control unit 09 update;

III.

Replacement and updating of the ECU 19;

IV.

Control unit 46 update;

V.

Control unit 15 update:

Refer to the procedure in the workshop manual regarding "Implementation of an SVM code".

IMPORTANT:
Improper use of this function can cause damage to the
ECUs.

Control unit A5 preconfiguration;
V.A Control unit A5 software download from SDCreator;

VI.
VII.

I.

1. To start the procedure to execute an SVM code,
select the “Special functions” card in ODIS.

Control unit A5 final update and update of
control units 13, 3C, CF, DB, DC;
Fault memory deletion.

IMPORTANT:

Do not perform other types of activity on the car
while executing the campaign.
Before starting the campaign, delete and resolve any
other faults present.
Carrying out the procedure blindly implies unsolvable damage to the control unit and resulting replacements.

2. Click on “SVM–Direct input: SVM for problemrelated update” and then on “Run test”.

NOTE:
Secure the key On during the entire procedure for
updating the various listed systems. Start a diagnostic
session with ODIS Service and keep the diagnostic
interface connected to the OBD socket. Do not close
the ODIS program or use it for other purposes.

Rev.00

This document and its contents are strictly confidential and private and are provided for informational purposes only and may not be copied, recorded, transmitted, further distributed to any other subject, or published, in whole or in part, by any means or in any form and for
any purpose, without the prior written authorization of Automobili Lamborghini S.p.A. All copyrights are the property of Automobili
Lamborghini S.p.A based on the applicable laws. The company reserves the right to make updates and modifications
doc. no.: L/V6_M06 Rev.[06]

5/33

L636A.08.19

To:
Subject:
Date:
Pages

Official After-Sales Network
Gateway ECU connectivity configuration
02 September 2019
33

3. Enter the campaign code “L636A0819A” in the
appropriate space at the top right and click
“Adopt”.

L636A0819A

Click "Adopt" to confirm.
7. The SVM function will automatically continue
with identification of the control units in the vehicle.

4. The SVM code entered is again displayed in the
dialog box. If the entered code is correct, click on
“Yes”. Otherwise click on “No” to cancel the
SVM procedure.
5. Wait for data to be acquired from all the control
units. This operation requires a few minutes.

8. It might become necessary to perform one or
more of the following operations in the SVM procedure:
 Coding;


Parameterization;



Calibration.

To perform these actions, it is usually necessary
to click on “Done/Continue” where requested and
to follow the instructions directly provided on the
ODIS dialog screens.
9. Click “Done/Continue” until the control unit 15
updating procedure is completed.

6. To run the SVM function and access the Lamborghini servers, you must have a valid GeKo account. Ensure that the laptop is correctly connected to the Internet. Enter your GeKo username in
the "User name" field and the PIN 1324 + the 6digit code currently displayed on the GeKo token
in the "Password" field.

10. Click “Done/Continue”.
11. Switch the key OFF for a few seconds.

Rev.00

This document and its contents are strictly confidential and private and are provided for informational purposes only and may not be copied, recorded, transmitted, further distributed to any other subject, or published, in whole or in part, by any means or in any form and for
any purpose, without the prior written authorization of Automobili Lamborghini S.p.A. All copyrights are the property of Automobili
Lamborghini S.p.A based on the applicable laws. The company reserves the right to make updates and modifications
doc. no.: L/V6_M06 Rev.[06]

6/33

L636A.08.19

To:
Subject:
Date:
Pages

Official After-Sales Network
Gateway ECU connectivity configuration
02 September 2019
33

12. Switch the key ON.
13. Select the function “15 - Read identification data”
from the “Guided functions” of control unit 15.

Table of reference for control unit 15
Software P.N.

4N0.959.655.H
4N0.959.655.R
4N0.959.655.Q

Software
version

Record number

Record
version

2710

4ML909602P

0001

2710

4ML909602P

0001

2710

4ML909602P

0001

15. The function asks you to also identify the slaves
of the control unit. Select “No”.
16. Select the function “15-Basic setting – Inertial
sensors” from the “Guided functions” of control
unit 15 and follow the instructions until the procedure is completed.

IMPORTANT: