Installation and Conversion Instructions

All
38/14

ENU

6692

6

Bicycle Rack

Revision:

This bulletin replaces bulletin Group 6, #38/14, dated August 23, 2016.
This revision now includes Cayenne (9YB) Coupe models.

Model Year:

As of 2003

Vehicle Types:

•
•
•
•
•
•
•
•
•

Concern:

Macan (95B) – all models with roof rails (I-no. 3S1/3S5) or with roof transport system (5W1/5W4)
911 Carrera (991)/Turbo (991) – all models, body type: Coupé ONLY with roof transport
system (549)
911 Carrera (997)/Turbo (997) – all models, body type: Coupé ONLY with roof transport
system (549)
Panamera (971) – all models with short wheelbase and with roof transport system (549)
Panamera (970) – all models with short wheelbase and with roof transport system (549)
Cayenne (9YA) – all models with roof rails (3S1/3S2) and roof transport system (5W1/5W4)
Cayenne (9YB) – all Coupé models with roof transport system (TEQUIPMENT)
Cayenne (92A) – all models with roof rails (3S1/3S5) or with roof transport system (5W1/5W4)
Cayenne (9PA) – all models with roof rails (3S7) or with roof transport system (3S8)

Instructions for assembly and use

Figure 1
Restriction:

NOT suitable for bicycles with carbon frame!

Note:

Up to three bicycle racks ( Figure 1) can be fitted on the base carriers (roof rail bars or roof transport
system, referred to below simply as "roof transport system") of the vehicles specified above.

Tequipment

Aug 1, 2019
Page 1 of 17

6

All
6692

ENU

Installation and Conversion Instructions

38/14

The bicycle rack:
•
•
•

Parts Info:

was tested on the vehicles specified above and adapted accordingly;
is approved for the transport of bicycles (mountain bikes or racing bikes) weighing up to max. 44 lbs
(20 kg);
can hold bicycles with a tube diameter in the frame holder (claw) area of 22 to 80 mm (circular crosssection) and up to max. 22 to 100 mm (oval cross-section - upright).
95B.044.800.06

 Bicycle rack, set

Parts List:

Figure 2

Aug 1, 2019
Page 2 of 17

———

1x

Bicycle rack (assembly  Figure 2 -1-) including:

———

2x

Wheel mount (front/rear) with turnbuckle  Figure 2 -2-

———

1x

Support tube (pivoting) with frame holder (claw)  Figure 2 -3-

———

1x

Retainer plate (rear)  Figure 2 -4-

———

1x

Quick-release clamp  Figure 2 -5-

———

1x

Retainer plate (front)  Figure 2 -6-

———

1x

Tensioning lever with lock  Figure 2 -7-

955.044.000.59

2x

 Spare key, set (2 keys with key code)  Figure 2 -8-

Tequipment

Installation and Conversion Instructions

Spare Parts:

Note:

All
38/14

ENU

6692

———

2x

Tensioning lever  Figure 2 -9-

———

2x

Rim protector  Figure 2 -10-

———

2x

Tension strap  Figure 2 -11-

———

2x

T-bolt, M6 x 61  Figure 2 -12-

———

1x

T-bolt, M6 x 35  Figure 2 -13-

———

3x

Barrel nut, M6  Figure 2 -14-

———

1x

"Bicycle frame mounting" notice  Figure 2 -15-

———

1x

Instructions for assembly and use (not shown)

95B.044.800.36

1x

 Assembly kit (small parts/spare parts), set comprising:

———

1x

Tensioning lever for lock/lock cylinder  Figure 2 -7-

———

2x

Tensioning lever  Figure 2 -9-

———

2x

Rim protector  Figure 2 -10-

———

2x

Tension strap  Figure 2 -11-

———

2x

T-bolt, M6 x 61  Figure 2 -12-

———

1x

T-bolt, M6 x 35  Figure 2 -13-

———

3x

Barrel nut, M6  Figure 2 -14-

6

The keys ( Figure 2 -8-) can be re-ordered if lost by specifying the part number and the code "Nxxx"
(possible codes range from N001 to N200) shown on the lock cylinder.

Technical Data: •
•
•
•
1

Length: 1,440 mm
Max. width: 350 mm
Max. height: 100 – 690 mm
Empty weight: 8.2 lbs (3.7 kg)1
Observe permissible roof load for the roof transport system ( Owner’s Manual, section on
'Weights')!

WARNING
Improper loading and fitting of the roof transport system or add-on modules
•

Danger of objects falling down

•

Danger of objects sticking out



Load the roof transport system or add-on modules in such a way that the load does not project over the
sides of the roof area.



Select the distances between several add-on modules mounted next to each other so that the transported
items cannot bump against each other during the trip.



Secure load sufficiently to prevent it from shifting during the trip.

Tequipment

Aug 1, 2019
Page 3 of 17

6


All
6692

ENU

Installation and Conversion Instructions

38/14

Check the roof transport system or add-on modules regularly before each trip and during an extended
trips to make sure they are seated correctly and securely on the vehicle.
CAUTION

Driving with a roof load
•

Higher center of gravity

•

Larger area exposed to the wind

•

Different vehicle handling



Adapt driving style accordingly.



Read the speed instructions and general information on the "Roof transport system" in the Owner's
Manual.

Information
Please inform the customer of this accordingly.
Work Procedure: 1

Prepare bicycle rack for assembly
1.1

Unpack bicycle rack and check that all items required are included.

1.2

Fit T-bolts
1.2.1

Unlock lock cylinder on tensioning
lever with lock ( Figure 3 -A-) and
remove tensioning lever with lock
( Figure 3 -B-).
1
2

– Key
– Tensioning lever with lock

Figure 3

Aug 1, 2019
Page 4 of 17

Tequipment

Installation and Conversion Instructions
1.2.2

All
38/14

ENU

6692

6

Insert M6 barrel nuts (3 ea.) into the
tensioning levers (3 ea.) ( Figure
4).
1
2
3

– Barrel nut, M6 (3 x)
– Tensioning lever (2 x)
– Tensioning lever with lock
(1 x)

Figure 4
Information
Check the marking at the bore!
1.2.3

Guide T-bolt (M6 x 35) from below
through the bore with the marking
( Figure 5 -inset-) on the retainer
plate (rear) ( Figure 5 -A-).
1
2
3
4
5
6
inset

–
–
–
–
–
–
–

T-bolt, M6 x 35
Retainer plate (rear)
Tensioning lever
T-bolt, M6 x 61
Retainer plate (front)
Tensioning lever with lock
Marking

Screw tensioning lever approx. 3
turns onto the T-bolt (M6 x 35) (
Figure 5 -B-).
1.2.4

Guide T-bolt (M6 x 61) through the
bore on the retainer plate (front 
Figure 5 -5-) ( Figure 5 -A-).

Figure 5

Screw tensioning lever with lock ( Figure 5 -6-) approx. 3 turns onto the T-bolt
(M6 x 61) (close to quick-release clamp) ( Figure 5 -B-).
Screw the second tensioning lever approx. 3 turns onto the T-bolt (M6 x 61)
( Figure 5).

Tequipment

Aug 1, 2019
Page 5 of 17

6

All
6692

ENU

Installation and Conversion Instructions

38/14

1.3

Fit tension strap and rim protector