Figure 90

19. Slide the rear link toward the rear of the
vehicle and out of the Moonroof rail.

Moonroof rail
Anti-rattle clip
Figure 91

20. Remove any debris / anti-rattle clip
material from the Moonroof rail area,
outlined in red in Figure 92.

Moonroof rail

Figure 92

44/54

NTB16-017a

21. Install the rear link into the Moonroof rail.

Guide pads

NOTE: The guide pads on the rear link
must compress to fit inside of the
Moonroof rail.

Anti-rattle clip
Figure 93

a. Gently compress the forward most
guide pad to insert it into the
Moonroof rail.

b. Gently compress the anti-rattle clip
while applying slight pressure toward
the front of the vehicle.

Slide

Compress

Figure 94

c. Using a 90 degree pick behind
the guide pad will assist in
compressing the rearmost pad
into the rear link.
Compress

Slide

d. Continue applying slight pressure
toward the front of the vehicle.

Figure 95

45/54

NTB16-017a

22. Align the rear link mounting holes with
the witness marks to assist in Moonroof
alignment.

Witness
marks
Figure 96

23. Repeat steps 3- 22, starting on page 38, for the other side of the Moonroof if replacing
both rear links.
24. Adjust the glass height to the proper position.


Refer to Moonroof Adjustment Clearances on the next page.
NOTE:
 Moonroof adjustment bolts should be slightly snug, not tight, to allow
adjustments.


Work one side at a time to raise and lower individual corners.



If the Moonroof needs to be moved fore/aft, loosen all adjustment bolts to
adjust.
Correct
angle

25. Tighten the adjustment bolts.


Torque bolts to: 5.5 N•m (0.56 kg-m,
48.68 in-lb.)

IMPORTANT:
 Make sure that the rear link is
level.


Figure 97 is shown with screws
removed to overemphasize
incorrect pivot angle.

Incorrect
angle

Figure 97

46/54

NTB16-017a

Moonroof Adjustment Clearances

26. Close the Moonroof and check adjustment.

27. Remove the old roof finisher adhesive
from the vehicle.
NOTE: Any remaining adhesive residue
similar to Figure 98 is acceptable.

Adhesive residue
Figure 98

47/54

NTB16-017a

28. Prepare the tip of Betaseal™ 57302N
Urethane Adhesive or equivalent.

Figure 99

NOTE:


To properly install the adhesive, cut a
notch in the tip similar to the one
shown in Figure 100.

Figure 100



Using a power caulk tool, similar to
the one shown in Figure 101, will aid
in adhesive application.

Figure 101

48/54

NTB16-017a

29. Add adhesive to the same locations as
the old adhesive.
Adhesive

NOTE: Apply the adhesive ½ inch (13
mm) high.

½” high
Figure 102
30. Verify the 3 roof finisher pins and 5 spacers have not become separated during roof
finisher removal.


Reinstall any pins or clips that have become separated.



Verify the 2 rearmost pins are centered in their slots.
NOTE: The forward most pin slot has no adjustment and will fit only one way.
Spacer

Pin

Figure 103

31. Tuck the roof finisher outer seal UNDER
the windshield glass seal.

Outer
seal

Windshield
glass seal

Figure 104

49/54

NTB16-017a

32. Starting from the front of the vehicle and
moving rearward, attach each push pin to
the roof (Figure 105).

33. After the push pins are all attached, seat
all square clips.
NOTE: Excess urethane sealant can hold
the roof finisher out of position at the
ends and not allow it to be seated.
Trimming the extra urethane sealant will
sometimes relieve the condition and
allow it to seat.

34. Tuck the rear roof finisher seal under the
rear window glass (Figure 106).

Center
push pin

Figure 105

Outer seal
Rear roof
finisher
l

Rear window
glass
Figure 106

35. Open the Moonroof.

36. Install the new T25 inboard screw into
the front of the roof finisher.


Inboard screw (T25)

Torque the screw to: 2.5 N•m (0.255
kg-m, 22 in-lb.)

Figure 107
50/54

NTB16-017a

37. Use a finesse tool to tuck the new roof
finisher seal into its channel.

Figure 108

38. Operate the Moonroof to the tilt
position.

39. Position the new bolt finisher as
shown in Figure 109.
Bolt finisher
Figure 109

40. Use a finesse tool to lift the bolt
finisher UP into position.

Figure 110
41. Repeat steps 27 – 40, starting on page 47, for the other side of the Moonroof if
replacing both anti-rattle clips.
42. Inspect the Moonroof, glass, roof finishers, and surrounding areas for cosmetic damage
or adhesive residue.
43. Allow the adhesive to cure for 24 hours.
51/54

NTB16-017a

Moonroof Initialization Procedure
1. Turn the ignition ON.
2. Close the Moonroof glass and power sunshade.
a. Press the Moonroof switch in the CLOSE position. Press the switch repeatedly if
needed.
b. Confirm the glass is not in the tilt-up position.
Read steps 3 and 4 carefully before proceeding. Step 4 includes an action that will
need to be performed quickly.
3. Press and hold the Moonroof switch in the CLOSE position until the glass and power
sunshade operates through several small movements (10 - 20 seconds).
4. After the glass has been motionless for 5 seconds, release the switch and within 1
second, press and hold the switch in the CLOSE position again.
5. Continue to hold the switch until the glass and power sunshade fully opens and then
fully closes.
6. Confirm the Moonroof has successfully initialized.
a. Tilt the glass.
b. Fully open and close the glass and power sunshade.
NOTE: The rear Moonroof glass is fixed and does not move.
7. Repeat the initialization procedure if the Moonroof does not function properly.
NOTE:
 It may take up to 5 attempts to successfully initialize the Moonroof.


If unsuccessful after 5 attempts, clear the memory by holding the switch in the
OPEN position for 15 seconds. Then, repeat the initialization procedure.

Anti-Pinch Function
1. Fully open the Moonroof.
2. Place a piece of wood near the fully closed position.
3. Close the Moonroof completely with auto-slide close function.
4. Check that the Moonroof opens approximately 150 mm (5.91 in) or reverses for 2
seconds without pinching a piece of wood and then stops.
5. Fully open the sunshade.
6. Place a piece of wood near fully closed position.
7. Close the sunshade completely with the auto slide close.
8. Check that sunshade opens approximately 150 mm (5.91 in) or reverses for 2 seconds
without pinching a piece of wood and then stops.
CAUTION: Do not test the anti-pinch function with your hands or other body parts
because they may be pinched.
52/54

NTB16-017a

PARTS INFORMATION
DESCRIPTION
GUIDE ASSY-SUNROOF (1)
(Right Side Moonroof Cable Repair Kit)
GUIDE ASSY-SUNROOF (1)
(Left Side Moonroof Cable Repair Kit)
DEFLECTOR ASSY-SUNROOF
(Moonroof Wind Deflector)
FINISHER ASSY-ROOF, RH
(Roof finisher Right Side) (3)
FINISHER ASSY-ROOF, LH
(Roof finisher Left Side) (3)
MOTOR ASSY-SUNROOF
(Moonroof Drive Motor)
MOTOR ASSY-SUNROOF
(Sunshade Drive Motor)
SHADE ASSY-SUNROOF, FRONT

PART NUMBER

QUANTITY

91358-4RA1A

1

91359-4RA1A

1

91280-4RA1A

1

91760-4RA3A

1

91761-4RA3A

1

91295-4RA2A

1

91232-4RA2A

1

(2)

1

SHADE ASSY-SUNROOF, REAR

(2)

1

FRAME ASSY-SUNROOF

91300-4RA3A

1

LINK ASSY - GUIDE, RH

91554-4RA1A

1

LINK ASSY - GUIDE, LH

91555-4RA1A

1

PLATE - SUNROOF COVER, RH

91262-4RA3A

1

PLATE - SUNROOF COVER, LH

91263-4RA3A
1
Betaseal™ 57302N
Urethane adhesive (4)
Urethane Adhesive
As needed
or equivalent
(1) This kit contains 1 knock. If a right and left knock are needed, both Left Side and Right
Side Moonroof Cable Repair Kits must be ordered.
(2) Refer to the Electronic Parts Catalog for the VIN specific part number.
(3) This part also includes one single use T25 screw.
(4) The DOW® automotive chemical Betaseal™ 57302N Urethane Adhesive is
recommended. Equivalent products may be used.

53/54

NTB16-017a

CLAIMS INFORMATION
Only Claim for the operations which were actually performed to repair vehicle.
Submit a Primary Part (PP) type line claim using the following claims coding:
OPERATION
Replace Knock Insert
Replace Sun Roof Wind
Deflector
Replace Sun Roof Panel
Finisher
Adjust Moon Roof Glass
Replace Sun Roof Panel
Finisher
Replace Moon Roof Drive
Motor
RPL Sunshade Drive Motor
Replace Link Assy- RH
Replace Link Assy- LH

PFP
(1)

OP CODE

91280-4RA1A

UQ20AA

SYM

DIAG

BX5LAA

FRT
0.3
(4)

(2)

UQ16AA

91300-4RA1A

BX5MAA

(3)

UQ16AA

91295-4RA1A

UQ26AA

91232-4RA1A
91554-4RA1A
91555-4RA1A

UQ27AA

0.4
ZE

32

(4)

UQ22AA

(1) Reference the Parts Information Table and use the applicable Part Number (91358-*****
or 91359-*****) as the Primary Failed Part.
(2) Reference the Parts Information Table and use the applicable Part Number (91760-*****
or 91761-*****) as the Primary Failed Part.
(3) Reference the Parts Information Table and use the applicable Part Number (91684-*****
or 91688-*****) as the Primary Failed Part.
(4) Reference the current Nissan Warranty Flat Rate Manual and use the indicated flat rate
time.
Expense code:
Expense Code
067

Description
Max Amount
Urethane adhesive $4.95

AMENDMENT HISTORY
PUBLISHED DATE

REFERENCE

February 19, 2016

NTB16-017

Original bulletin published

August 12, 2019

NTB16-017a

Updated ROOF FINISHER
REPLACEMENT and added REAR LINK
REPLACEMENT sections.

54/54

DESCRIPTION

NTB16-017a