NHTSA ID Number: 10164631
Manufacturer Communication Number: SC-19-95
TSB/Document Date: 2019-09-10
Summary
The reason for this software update is to update various controllers. All the included Proterra Catalyst E2 vehicles require a change to the software/configuration for the following items: Battery Pack
Software, Charge Controller, ESM Software, Powertrain Controller, DWP/Dash Software, and Body Controller (ZR)
ISSUE DATE:
SERVICE BULLETIN SUBJECT:
VINs or MODELS AFFECTED:
COMPLETE BY:
SERVICE CAMPAIGN #:
8/12/2019
E2 Ver2 Software Verification and Update
Catalyst 40 with ProDrive BTMS and All Catalyst 35 E2
Vehicles
Next Available Service Opportunity
SC-19-95
NOTICE! It is expected that this process may require up to 3 hours per bus. Please
schedule appropriately to minimize vehicle downtime.
VEHICLE SOFTWARE VERIFICATION AND UPDATE
Description
The reason for this software update is to update various controllers. All the included Proterra Catalyst
vehicles require a change to the software/configuration for the following items:
•
•
•
•
•
•
•
Battery Pack Software
Charge Controller
ESM Software
Powertrain Controller
DWP/Dash Software
Body Controller (ZR)
Verify Only – Traction Motor Inverter Firmware Version
Summary of Software Changes
This update is to verify the latest software versions are installed for all controllers on the vehicle.
•
•
•
•
•
•
Battery Pack Software
o Improved recovery from INTCAN CAN Errors
o Additional Range Modes to allow for higher resolution SOH updates
o Balancing disabled during fast charge to prevent temperature de-rates to charging
o HVIL improvements to prevent sudden loss of power when only one string is enabled
Charge Controller
o Improved high power charge handling
o Broadcast of version numbers and EVSE parameters on CAN
ESM Software
o Improved SOC calculations and low voltage performance
Powertrain Controller
o Hill hold improvements
o Updates to enable 315 tire installation
DWP/Dash Software
o Added voltage display for 24V batteries
o Added support for Brake Wear indications (if installed)
Body Controller (ZR)
o Improved handling of 5 position door switch input
▪ Doors will now support automatic “re-close” after obstruction (if enabled)
o Added support for three door vehicles
o Added support for new dash content
o Hill hold feature improvements
▪ New feature: Press-to-set hill hold activation and audible hill hold alert (if
enabled)
o Support for Auxiliary heating (fuel fired heater) system
o Support for cabin HVAC pre-conditioning (if supported by vehicle telemetry system)
o Improved Ride Height configuration handling
o Customer-requested updates
▪ SWAT switch functionality
▪ ADA chime to discrete output
▪ Aux Heat disable while charging feature
2|Page
Headquarters: 1815 Rollins Road, Burlingame, CA 94010
East Coast Manufacturing: 1 Whitlee Court, Greenville, SC 29607
West Coast Manufacturing: 383 Cheryl Lane, City of Industry, CA 91789
Tools/Programs Required
Tools Required:
• Laptop Computer
• K-line USB Adapter (dash programming)
• USB to Serial Adapter (dash programming)
• Proterra OBD Breakout cable “Octopus”
• PCAN USB dongle
• Nexiq USB-Link or USB-Link 2
NOTE: IT IS NOT PERMITTED to use the Logena Service tool to perform the Body Controller
software update: this tool has been obsoleted. This tool does not maintain configuration
information and may result in unsafe/undesirable vehicle operation if used to flash body
controller software.
Programs Required:
• BMS flashing utility (MonacoUDSClient)
• Proterra Diagnostic Tool
• CAVTAN Parameter Editor v3.03 (dash programming)
3|Page
Headquarters: 1815 Rollins Road, Burlingame, CA 94010
East Coast Manufacturing: 1 Whitlee Court, Greenville, SC 29607
West Coast Manufacturing: 383 Cheryl Lane, City of Industry, CA 91789
Software Files Required / Preparation
It is recommended that you copy the entire “service bulletin files” folder to your local machine in order
to more effectively keep track of the software versions you are deploying:
\\bus.local\files\Engineering\Service Bulletins\Service Bulletin Files for SB-19-95\
•
Body Controller Version 60.05:
o 047344.ZR32A_A
•
Powertrain:
o Main Version 2.4.1
o 042887.hex
•
CCS Charger Controller:
o Dual Port
▪ Part number 047977.zip
▪ CC_2_0_4.srec
o Single Port
▪ Part Number 047978.zip
▪ CC_2_1_4.srec
•
ESM Controller Version 2.0.0:
o Part Number 043836
o ESM_Catalyst_2_0_0_release_04_11_2019.srec
•
BMS (E2 Pack) Software:
o Part Number 038975
o 0117340DE_MonacoBMS_Main.mbms
o 0117340AE_MonacoSC_Safety.mbms
•
Dash Software - Version 8:
o 044843_rev08.zip
4|Page
Headquarters: 1815 Rollins Road, Burlingame, CA 94010
East Coast Manufacturing: 1 Whitlee Court, Greenville, SC 29607
West Coast Manufacturing: 383 Cheryl Lane, City of Industry, CA 91789
Contents
Description ............................................................................................................................................ 1
Summary of Software Changes ......................................................................................................... 2
Tools/Programs Required.................................................................................................................. 3
Software Files Required .................................................................................................................... 4
Connect to the Vehicle to Start the Proterra Diagnostics Tool .............................................................. 6
Verify and Update the BMS (Battery Pack) Software ............................................................................ 9
Verify Current Software Version ........................................................................................................ 9
Update Using the Proterra Diagnostic Tool ..................................................................................... 10
Update Using MonacoUDS Client (Alternate Method) ..................................................................... 13
Verify and Update ESM Controller Software Version: ......................................................................... 20
Verify Current Software Version ...................................................................................................... 20
Update Using the Proterra Diagnostic Tool ..................................................................................... 21
Update Using Microboot (alternate method) .................................................................................... 23
Verify and Update Charge Controller Software Version ...................................................................... 24
Verify Current Software Version ...................................................................................................... 24
Update Using the Proterra Diagnostic tool ...................................................................................... 25
Update Using Microboot (alternate method) .................................................................................... 27
Verify and Update Powertrain Software Version ................................................................................. 28
Verify Current Software Version ...................................................................................................... 28
Update Powertrain Software............................................................................................................ 29
Verify and Update Dash Software Version .......................................................................................... 31
Verify Current Software Version ...................................................................................................... 31
Update Dash Software .................................................................................................................... 32
Verify and Update Body Software Version .......................................................................................... 36
Verify Current Software Version ...................................................................................................... 36
Update Body Controller Software .................................................................................................... 38
Store/Import Customer Configuration Dataset................................................................................. 42
Verification of Customer Configuration ............................................................................................ 44
Verify Traction Motor Software Version .............................................................................................. 45
Verify Current Software Version ...................................................................................................... 45
Check List for Software Versions Deployed ........................................................................................ 46
5|Page
Headquarters: 1815 Rollins Road, Burlingame, CA 94010
East Coast Manufacturing: 1 Whitlee Court, Greenville, SC 29607
West Coast Manufacturing: 383 Cheryl Lane, City of Industry, CA 91789
Connect to the Vehicle to Start the Proterra Diagnostics Tool
This process will guide the user to connect to the vehicle with the Proterra Diagnostics Tool.
1. Turn ON the 12/24V rear Vehicle Master Disconnect located behind the vehicle curbside rear
charge port access panel.
2. Turn ON the bus Master Run Switch at the Driver's Workplace and ensure the Dash screen is
ON to display “KEY ON”.
a. This places the vehicle into Key On / Low Voltage state for controller versions to be
checked prior to software flash.
3. For Body Controller Programming:
a. Turn OFF the Master Run Switch at the Driver’s Workplace and ensure the dash screen
is OFF.
b. Turn ON the bus “programming switch” inside the street side wheel well box.
4. Using a T30 Torx screwdriver or appropriate tools, remove the two access covers:
a. Street side wheel well electronics cabinet (ECAB) panel for access to the OBDII Port.
b. Rear deck access panel for OBDII Diagnostic port (NOTE: on E2-35 foot buses this is
located behind the rear barn doors on the left hand side).
5. Power up (boot) the Proterra-supplied laptop containing the Proterra Diagnostic Tool.
6|Page
Headquarters: 1815 Rollins Road, Burlingame, CA 94010
East Coast Manufacturing: 1 Whitlee Court, Greenville, SC 29607
West Coast Manufacturing: 383 Cheryl Lane, City of Industry, CA 91789
6. Connect the Nexiq USB Link2 device to the laptop and to the appropriate OBDII Diagnostic
Port.
7. For example, here is the Nexiq USB Link connected to the Diagnostic Port located on the
street side wheel well electronics cabinet (eCab):
Diagnostic Port
Nexiq USB Link
8. On the laptop, double-click on the Proterra Diagnostics Tool software icon to
start the software.
9. When the program opens, read and click OK for the prompt.
10. On the Home tab, select the appropriate device from the drop down and click “Connect”.
7|Page
Headquarters: 1815 Rollins Road, Burlingame, CA 94010
East Coast Manufacturing: 1 Whitlee Court, Greenville, SC 29607
West Coast Manufacturing: 383 Cheryl Lane, City of Industry, CA 91789
11. Once the diagnostic tool has connected to the vehicle, you will have a VIN number and
connection status displayed on the home screen, and tabs available to navigate.
8|Page
Headquarters: 1815 Rollins Road, Burlingame, CA 94010
East Coast Manufacturing: 1 Whitlee Court, Greenville, SC 29607
West Coast Manufacturing: 383 Cheryl Lane, City of Industry, CA 91789
Verify and Update the BMS (Battery Pack) Software
This procedure checks the Body Controller software version and maintains the body controller
parameter configuration data across the flash download of new software.
Verify Current Software Version
1. With the Diagnostic tool connected to the vehicle at the front or rear deck OBDII Port, navigate
to the “Battery Packs” Tab and view the Main and SC SW Versions.
a. If these do not read 117340A and 117340D, as shown below, you must download
battery pack firmware.
b. Be sure you check for each Pack using the drop down in the upper right corner.
Click
Battery Packs
Software
Versions
Pack
Selection
c. NOTE: This pack version will only refresh if you cycle power to the controller (by turning
off the Master Disconnect at the rear of the Vehicle) and also disconnect/reconnect the
Proterra Diagnostic tool.
9|Page
Headquarters: 1815 Rollins Road, Burlingame, CA 94010
East Coast Manufacturing: 1 Whitlee Court, Greenville, SC 29607
West Coast Manufacturing: 383 Cheryl Lane, City of Industry, CA 91789
Update Using the Proterra Diagnostic Tool
1. Ensure the laptop battery is full or it is connected to AC power. The procedure can take up to
ten minutes per pack to complete.
2. Ensure you have the latest software file **.mbms to a known location on the service technician’s
computer (Folder or Desktop).
IMPORTANT! NEVER access the software from the USB memory device, ALWAYS copy the
software files to your computer hard drive and access the software from this location. Secure the bus
with the Vehicle Master Disconnect in the rear ON.
3. Turn the dash Master Switch to ON. Do not press START. Use the hazard lights if necessary
to maintain bus power.
4. With the Proterra diagnostic tool connected to either the front or rear diagnostic port (must
have BCAN data available), navigate to the Configuration tab.
Click
Configuration
Beside Battery
Mgmt System,
Click Start Flash
NOTE: If desired, you can now turn the Master Switch to “OFF”. The battery system remains
active as long as the 12/24V switch is on. This may improve software download speed.
5. Select the option for Battery Management System “Start Flash”.
6. In the pop-up window, select one of the following software configurations to load the
appropriate software into the two controllers for each pack:
a. Pack Safety Controller (SC): 117340A.
b. Main Pack Controller: 117340D.
7. A popup window will appear, “Scanning for available battery management systems”.
10 | P a g e
Headquarters: 1815 Rollins Road, Burlingame, CA 94010
East Coast Manufacturing: 1 Whitlee Court, Greenville, SC 29607
West Coast Manufacturing: 383 Cheryl Lane, City of Industry, CA 91789
8. Once it is finished scanning, a window with a drop-down list box appears:
9. Select a controller from the drop down list:
a. Safety Controller should display the following per pack, once properly updated:
b. Main controller should display the following per pack, once properly updated:
10. Select a pack controller and click the “Flash” button.
11. The Programming window will come up and may take a few minutes to complete.
11 | P a g e
Headquarters: 1815 Rollins Road, Burlingame, CA 94010
East Coast Manufacturing: 1 Whitlee Court, Greenville, SC 29607
West Coast Manufacturing: 383 Cheryl Lane, City of Industry, CA 91789
12. When the Programming screen completes, the version numbers will update in the list to show
you have completed that pack (BMS1 Safety has been updated below):
13. After all packs have been updated, cycle power to the bus.
14. Disconnect the diagnostic tool on the home tab and again click Connect.
a. This will refresh the pack version information and allow you to verify all four packs are
properly updated on the “Battery Pack” tab.
Click
Battery Packs
Software
Versions
Pack
Selection
12 | P a g e
Headquarters: 1815 Rollins Road, Burlingame, CA 94010
East Coast Manufacturing: 1 Whitlee Court, Greenville, SC 29607
West Coast Manufacturing: 383 Cheryl Lane, City of Industry, CA 91789
Update Using MonacoUDS Client (Alternate Method)
1. Ensure the laptop battery is full or it is connected to AC power. The procedure can take up to
ten minutes per pack to complete.
2. Download the archive file (.zip or .rar) containing the flashing utility, BMS files, and instructions
to your laptop hard drive.
3. Extract the archive file to a folder at a location of your choosing; remember this location for
future steps.
4. Connect the PCAN dongle to the laptop.
5. Close all CAN utilities running on the laptop: PCAN Explorer, DST, CANalyzer, etc.
Note: These programs can interfere with the tool’s ability to use the PCAN dongle and will
prevent the tool from correctly flashing the BMS.
6. Launch the flashing tool: MonacoUDSClient.exe.
Note: Do not attempt to run the tool straight from the archive file; extract it first, then run it from
the extracted folder.
13 | P a g e
Headquarters: 1815 Rollins Road, Burlingame, CA 94010
East Coast Manufacturing: 1 Whitlee Court, Greenville, SC 29607
West Coast Manufacturing: 383 Cheryl Lane, City of Industry, CA 91789
7. Click the “Connect” button beside the Connection drop-down menu. If this button is “grayed
out” or not available, you may need to restart your computer to correctly connect to the dongle.
8. The button should change to “Disconnect” once proper communication is established.
NOTE: You will also get a “Connection Successful” message in the status window at the
bottom.
9. Proceed to the next section: Connecting to the bus.
14 | P a g e
Headquarters: 1815 Rollins Road, Burlingame, CA 94010
East Coast Manufacturing: 1 Whitlee Court, Greenville, SC 29607
West Coast Manufacturing: 383 Cheryl Lane, City of Industry, CA 91789
Connecting to the Bus
10. Secure the bus with the Vehicle Master Disconnect in the rear ON.
11. Turn the dash Master Switch to ON. Do not press START. Use the hazard lights if necessary
to maintain bus power.
12. Remove the rear deck access cover behind the back seats using a T30 Torx driver, or square
key if the bus is so equipped.
13. Connect the OBD to DB adapter cable to the rear diagnostic port, then connect the PCAN
dongle to the BCAN port on the cable.
14. Click on the “Scan Dialog” button, then “Start Scan” on the window that pops up.
Note: This will scan for all connected BMS units. On a 4 pack bus you should see 8 instances
of “true” in the first column, as seen below.
15. Once all four packs’ Safety and Main controllers are verified as online, you may proceed with
the flashing procedure.
15 | P a g e
Headquarters: 1815 Rollins Road, Burlingame, CA 94010
East Coast Manufacturing: 1 Whitlee Court, Greenville, SC 29607
West Coast Manufacturing: 383 Cheryl Lane, City of Industry, CA 91789
Flashing the BMS
16. Select the file to flash, under “Select Image.” Click on “Select,” then navigate to the files you
extracted in Step 2 of setup. Select the file labeled “0117340AE_MonacoSC_Safety.mbms”
Note: Each pack will need to be flashed twice, once for the MAIN and once for the SAFETY
controller. The order in which these are done does not matter.
17. Under “Select Device to Flash” use the drop-down menu to select the BMS you are working
on; in the example images, this is BMS01.
16 | P a g e
Headquarters: 1815 Rollins Road, Burlingame, CA 94010
East Coast Manufacturing: 1 Whitlee Court, Greenville, SC 29607
West Coast Manufacturing: 383 Cheryl Lane, City of Industry, CA 91789
18. Click on the “Enter Bootloader Mode” button. A dialog box will appear to ask for confirmation.
Select “Yes” to confirm and proceed. A second dialog box will appear to notify you the
application reset command was sent, click OK to dismiss it.
19. Click “Flash Device” to load new software into the BMS. A dialog box will appear to ask for
confirmation to proceed, select “Yes” to continue. Another dialog box will appear when flashing
is complete, click OK to continue.
17 | P a g e
Headquarters: 1815 Rollins Road, Burlingame, CA 94010
East Coast Manufacturing: 1 Whitlee Court, Greenville, SC 29607
West Coast Manufacturing: 383 Cheryl Lane, City of Industry, CA 91789
20. Click “Restart Device” to send a reset command to the BMS. A confirmation box will appear,
click “Yes” to confirm the command.
Note: You will NOT receive a notification box after this, but the Status window will indicate the
restart commands were sent.
21. Repeat step 1-5, this time selecting the file labeled “0117340DE_MonacoBMS_Main.mbms” as
the image to be loaded.
22. Verify the new software load by using the “Scan Dialog” option on the client main screen. You
should see new App Version numbers for the BMS you just flashed, matching the 7-digit
number from the file names selected.
Note: If you do not see these new version numbers, or a pack does not show as present, you
will need to run the flashing procedure again and verify that the controllers reset.
23. Repeat steps 1-6 for the other packs on the bus to update the BMS boards.
18 | P a g e
Headquarters: 1815 Rollins Road, Burlingame, CA 94010
East Coast Manufacturing: 1 Whitlee Court, Greenville, SC 29607
West Coast Manufacturing: 383 Cheryl Lane, City of Industry, CA 91789
Verification and Close-out
24. Run the Scan Dialog once the all the packs have been updated and verify that all packs
installed are Present and the version numbers for all Safety Controllers are the same and
version numbers for all Main Controllers are the same.
25. Close out of the MonacoBMS client, then disconnect the PCAN dongle and adapter cable.
26. Turn the bus Dash Master Switch to OFF, then the Vehicle Master Disconnect to OFF.
Note: Wait 30 seconds.
27. Turn the Vehicle Master Disconnect switch back to ON.
28. Turn the Dash Master Switch ON, then press START.
29. Verify no battery faults are present when the bus reaches RUNNING status.
19 | P a g e
Headquarters: 1815 Rollins Road, Burlingame, CA 94010
East Coast Manufacturing: 1 Whitlee Court, Greenville, SC 29607
West Coast Manufacturing: 383 Cheryl Lane, City of Industry, CA 91789
Verify and Update ESM Controller Software Version:
This procedure checks the ESM Controller software version and upgrades as necessary.
Verify Current Software Version
1. Connect Proterra Diagnostics tool to either front or rear OBDII connector.
2. Navigate to High Voltage Tab.
3. Verify the High Voltage Batteries Controller Software version is “ESMCATALYST_2.0.0”:
4. In this screenshot, the ESM controller software version (middle of the screen) is 2.0.0.
5. If the version is not 2.0.0, proceed to the next section to update the controller software.
20 | P a g e
Headquarters: 1815 Rollins Road, Burlingame, CA 94010
East Coast Manufacturing: 1 Whitlee Court, Greenville, SC 29607
West Coast Manufacturing: 383 Cheryl Lane, City of Industry, CA 91789
Update Using the Proterra Diagnostic Tool
6. Ensure you have the latest software file ESM_**.srec to a known location on the service
technician’s computer (Folder or Desktop).
IMPORTANT! NEVER access the software from the USB memory device, ALWAYS copy the
software files to your computer hard drive and access the software from this location.
7. Turn ON the 12/24V rear Master Disconnect located behind the vehicle curbside rear upper
access panel.
8. Turn OFF the bus High-Voltage Master Switch at the Driver's Workplace and ensure the
Dash screen is OFF.
9. Once connected to the vehicle with the Proterra Diagnostics tool, Click on the “Configuration
Button” to open the Configuration screen and then click the Battery Master Controller “Start
Flash” Button.
Click
Configuration
Beside Battery
Master Controller,
Click Start Flash
21 | P a g e
Headquarters: 1815 Rollins Road, Burlingame, CA 94010
East Coast Manufacturing: 1 Whitlee Court, Greenville, SC 29607
West Coast Manufacturing: 383 Cheryl Lane, City of Industry, CA 91789
10. The following screen will be displayed. Navigate to the location where you stored the
configuration file earlier. Select the file and click “Open” to load the file.
Select the file and
Click Open
11. The Proterra Diagnostic Tool will attempt to connect to the device.
NOTE: You may receive an error on the first attempt. If so, retry by clicking the Battery
Master Controller “Start Flash” button again.
Error message on
failed first attempt
12. When the software update begins, and the following screens will be displayed.
13. The software update may take several minutes to complete. When the update is complete
the following screen will be displayed. Click the “OK” button to complete the update process.
Click OK
14. The software update is now complete.
15. Reset the bus and proceed.
22 | P a g e
Headquarters: 1815 Rollins Road, Burlingame, CA 94010
East Coast Manufacturing: 1 Whitlee Court, Greenville, SC 29607
West Coast Manufacturing: 383 Cheryl Lane, City of Industry, CA 91789
Update Using Microboot (alternate method)
The purpose of this procedure is to update the ESM Controller software version.
1. Ensure you have the latest program and software file ESM_**.srec to a known location on the
service technician’s computer (Folder or Desktop).
IMPORTANT! NEVER access the software from the USB memory device, ALWAYS copy the
software files to your computer hard drive and access the software from this location.
2. Turn ON the 12/24V rear Master Disconnect located behind the vehicle curbside rear upper
access panel.
3. Turn OFF the bus High-Voltage Master Switch at the Driver's Workplace and ensure the Dash
screen is OFF.
4. Power up (boot) the Proterra-supplied laptop containing the MicroBoot executable file.
5. Connect the octopus cable to the OBD port located in the Rear Deck of the bus.
6. Connect the PCAN dongle to the PCAN connection on the octopus cable.
7. Verify no other CAN utilities are running on the laptop; close PCAN Explorer, Proterra
Diagnostic Tool, etc.
8. Connect PCAN dongle to the USB port on the laptop.
9. Launch MicroBoot on the laptop.
10. Use the “Browse” button to navigate to and select the SREC file to be loaded.
a. The software will load automatically from this point.
11. The software update may take several minutes to complete. When the update is complete the
following screen will be displayed. Click the “OK” button to complete the update process.
- Advanced VCI Box, Industry-leading J2534 Pass-Thru...
- High-Speed OEM-Level Diagnostics & Programming: Unlock true...
- Coverage for 17 Car Brands & Ultra Reliability: Works...
- User-Friendly RLink Platform & Expert Support: TOPDON’s...
- 6.6 ft USB-C Cable & Portable Storage Case: The RLink J...
Last update on 2026-06-23 / Affiliate links / Images from Amazon Product Advertising API
If the PDF is very large, it may not load in the preview below.
Some older TSBs had multiple PDFs — visit the NHTSA Website to view all PDFs.
If the TSB PDF does not show, download or view it on the NHTSA Website.
Click on the (+) Plus Sign
Then Click on Associated Document(s)
Search NHTSA Database for Recalls
Search NHTSA Database for Vehicle Investigations
View Latest Vehicle Investigations
Search NHTSA Database for Vehicle Complaints
View Latest Vehicle Complaints
TSB/Document ID: SC-19-95
Replacement Service Bulletin Number:
MFR Communication Date: 2019-08-13
MFR Internal Campaign ID/Software Version:
Communication Type: Service Bulletin/Repair Instructions
NHTSA Components: ELECTRICAL SYSTEM
MFR Component System:
MFR Component Subsystem:
Previous TSB | Next TSB |
- 【OE-Level Full System Diagnostics-Lifetime F*REE Software Updates】The VDIAGTOOL D200 OBD2 Scanner for cars is a all system bidirectional scan tool that enjoy lifetime f*ree software updates, delivers complete system coverage. reading/clearing codes across engine, transmission, ABS, SAS, EPB, TPMS plus full access to body, chassis, powertrain and all control modules. This D200 Bidirectional car scanner works with most 1996+ OBD2 gasoline and hybrid
cars and light trucks. It does NOT support pure electric and heavy-duty trucks. PLEASE CHECK COMPATIBILITY BEFORE ORDERING or Contact us with VIN to confirm compatibility. - 【Supports OBD2 Full Functions-ZERO Subscription Fees】D200 Bidirectional OBD2 Scanner is a upgarde of universal car code reader. It supports OBD2 full functions to help you turn off the annoying instrument fault indicator, such as read/clear codes, O2 sensor test, I/M readiness, on-board monitor test, datastream, freeze frame, E-VAP system test, and retrieve vehicle information. This professional obd2 scanner diagnostic tool can full access to diagnostics, reset tools and maintenance features with a single payment. NOTE: The fault code can only be cleared after the vehicle's malfunction has been repaired; please ensure the vehicle issue is fixed before clearing the code.
- 【D200 Hidden 2 Advantages: 1. $169 Expandable 49+ Advanced Resets. 2. $199 Get J2534 P*a*s*s-Thru Programming】Your core car diagnostics and 26 reset remain lifetime f*ree for everyday maintenance. When you need deeper repair capability, upgrade with 3-year access for $169 in Store on VDIAGTOOL App, gaining 49+ advanced resets. D200 configured with J2534 hardware, upgrade only when you need without replacing the entire device. You also can Lifetime Unlock for $199 in Store one-time, perform module programming, software re~flashing and ECU data updates directly. Supports 17+ major brands, including for BMW, for Audi, for GM, for Ford and more. Note:D200 does‘t provide any OE software.
- 【Full Bidirectional Control / Active Tests】The D200 car scanner diagnostic tool is a true bidirectional scan tool that lets you send commands directly to the vehicle’s ECU for active tests. Quickly test fuel pumps, relays, solenoids, injectors, cooling fans, windows, sunroofs and more to verify operation instantly. Get dealership-level diagnostic control at a fraction of the cost (ofter $100-200$ per diagnostic visit), reduce guessworkand confirm repairs faster, avoid unnecessary parts replacement, towing fees and wait times.
- 【26 F*ree Essential Reset & Relearn Functions – Everyday Maintenance Made Easy】Handle common maintenance and repair jobs without visiting the shop. The D200 code readers & scan tools includes 26 f*ree high-demand reset functions, including Oil Reset, EPB Service, SAS Calibration, ABS Brake Bleeding, Throttle Relearn, Injector Coding, Headlight Adjustment, Tire Size Reset and more. Perfect for home car owners, mechanics and DIYers – just plug and diagnose anytime, anywhere! Note: Service functions vary by vehicle model—please confirm compatibility.
- 【A MUST-HAVE TOOL FOR DIYERS】 - VDIAGTOOL VD10 car code reader is an incredibly useful obd scanner for each car owner or hobbyist, even for those with little to no experience when it comes to vehicle mechanics! Similar to a fixd car diagnostic tool, using this car diagnostic scanner is extremely easy. All you have to do is attach it to your car OBDII port and you can diagnose car problems in seconds! Read Codes (DTCs); Clear Codes; Live Data; View Freeze Frame; I/M Readiness; Vehicle Information.
- 【KEEP ENGINE IN GOOD STATUS】 - VDIAGTOOL check engine code reader brings a fast access to scan, read the car fault code, show its definition on the screen instantly, troubleshooting to find the root causes of problems, erase the engine fault code and turn off the MIL (Malfunction Indicator Light). Similar to a fixd car diagnostic tool, this car code reader helps ensure your engine stays in top condition.
- 【READ/CLEAR CODES & DTC LOOKUP】- No search online & saving your time, this vehicle car code reader retrieves generic (P0, P2, P3, and U0), manufacturer specific (P1, P3, and U1) codes, pending codes and displays DTC definitions based on the built-in database(more than 3000 codes) on the TFT screen, find out the root causes and clear the codes after fixed.
- 【LIVE DATA & RETRIEVE FREEZE FRAME】 - This diagnostic scan tool for accurate diagnosis enables you to retrieve data from vehicle sensors, such as Engine RPM, Intake air temperature, Short/Long term fuel, Misfire data and etc. The freeze frame is stored in the PCM together with the diagnostic trouble code (DTC) related to the fault. Comparable to a fixd car diagnostic tool, the VD10 car code reader car scanner can be a valuable & practical diagnostic aid and also greatly help when diagnosing intermittent problems.
- 【I/M READINESS for THE S-nn-0-g CHECK】- OBDII vehicle may not pass the annual inspection unless the required monitors since reset are complete. So you should at least read the readiness monitors and make sure they are ready. This car obd2 scanner diagnostic tool is equipped with I/M readiness function to check the operations of the e-m-issi0n system on OBD2 compliant vehicles, run I/M monitor readiness test, checking if the pass vehicle s-m-0-g inspection.
- 【Professional Diagnostics】 The VD80 BT Lite bidirectional obd2 scanner is a professional OBD2 scanner diagnostic tool, delivering vehicle diagnostics right in your own garage. It supports 4,000+ active diagnostic tests, 28+ maintenance service functions, ECU coding, PMI calibration, brake service reset, and OEM-grade full-system vehicle scanning—perfect for DIYers and pros looking for powerful automotive tools. The available function tests vary by model—please to confirm compatibility.
- 【ADVANCED ECU CODE, CUSTOMIZE OE-SETTINGS】As a complete car code reader and reset tool, the VD80 BT Lite bidirectional obd2 scanner supports ECU coding for VW, for Audi, for BMW, for Benz, for Mitsubishi and more. PMI function for Ford/for Lincoln/for Mazda, supports copy data into new module. Step-by-step Guided Diagnostics makes complex jobs easier—making this one of the most reliable code readers & scan tools on the market.
- 【100000+ Vehicles Compatibility – CAN FD/DOIP】 VD80 BT Lite Auto Scanner Compatible with 100,000+ vehicles worldwide, this bidirectiona car scanner works with all OBD2-compliant vehicles manufactured after 1996, covering more than 100 brands worldwide. It also supports CAN FD, DOIP and FCA Secure Gateway protocols, boost 2X faster data transfer, covers 99% of U.S., EU and Asian cars. With 22 languages and 2 years of f*ree updates—future-proofing your car reader diagnostic for all cars.
- 【28+ Maintenance Services & Calibration Functions】VD80 BT Lite scanner for car Supports 28 maintenance services, including resetting oil and service lights after routine maintenance, registering new batteries for proper system operation, and clear clogged filters and restore performance. Additionally, it calibrates TPMS sensors after tire rotations, resets brake systems after pad replacements, relearns steering angle sensors after alignments, and more. These functions help your vehicle quickly and accurately return to peak performance—without the costly dealer visits.
- 【True Bidirectional Control – Diagnose with Confidence】Standing out with full-system coverage and extensive active test capabilities, the VD80 BT Lite bidirectional scan tool retrieves data from electronic control units and performs a wide range of active tests. You can real-time control over modules like fuel pumps, windows, A/C clutches, and relays. Perform 100+ advanced functions including throttle adaptation, injector coding, VIN write, idle relearn, and ABS bleed—helping you fix it right the first time with this all-in-one car diagnostic scanner.
Last update on 2026-06-23 / Affiliate links / Images from Amazon Product Advertising API
This product presentation was made with AAWP plugin.