T-SB-0158-18

Rev1

December 14, 2018

Floor Mat Installation During PDS
Service
Category

General

Section

Pre-Delivery Service

Market USA

Applicability
YEAR(S)

MODEL(S)

2020

4Runner, 86, Avalon, Avalon
HV, C-HR, Camry, Camry
HV, Corolla, Corolla
Hatchback, Corolla HV,
Highlander, Highlander HV,
Land Cruiser, Mirai, Prius,
Prius C, Prius Prime, RAV4,
RAV4 HV, Sequoia, Sienna,
Supra, Tacoma, Tundra,
Yaris SD MEX-Prod

ADDITIONAL INFORMATION

REVISION NOTICE
July 03, 2019 Rev1:
 Applicability has been updated to include 2020 model year Supra vehicles.
 The Hook and Loop Style section has been added.
Any previous printed versions of this bulletin should be discarded.

© 2019 Toyota Motor Sales, USA

Page 1 of 15

T-SB-0158-18

Rev1

December 14, 2018

Page 2 of 15

Floor Mat Installation During PDS
Introduction

2020 model year Toyota vehicles are equipped with driver side floor mat retainers to secure the
floor mat in the correct position. In addition, some models may also utilize retainers for passenger
side and rear seat floor mats. During Pre-Delivery Service (PDS), follow the appropriate Installation
Procedure to attach the driver side, and if applicable, the passenger side and rear seat floor mats
to the vehicle carpet using the floor mat retainers. If installation instructions are included in the floor
mat kit, place the instructions in the vehicle’s glove box for customer reference.
CAUTION
 ALWAYS verify the floor mat is designed specifically for the model and model year it is being
installed in.
 ONLY use floor mats that can be secured using the retainers. ALL OEM Toyota floor mats are
specifically designed to fit correctly and be secured using the retainers.
 Make sure the floor mat is properly placed on the vehicle carpet and secured with the retainers.
If the driver side floor mat is NOT properly placed and secured, it could slip and interfere with
the movement of the pedals during driving and may cause an accident.
 Verify the operation of the accelerator, brake, and clutch (if equipped) pedals and clearance to
the mat.
 NEVER install more than one floor mat at a time in the driver’s seating position.
 If applicable, ANY secondary set of floor mats (based upon customer preference, such as the
all-weather floor mats or other floor mats) MUST be placed in the trunk with ALL the packaging
material intact. Do NOT install the secondary mat on top of the primary floor mat already
installed in the driver’s seating position.

Warranty Information
OP CODE

DESCRIPTION

TIME

OFP

T1

T2

N/A

Not Applicable to Warranty

–

–

–

–

Procedures



Hook Style ................................................................................................................................ 3



Hook Style With Locking Clip ................................................................................................... 5



Knob Style With Locking Clip ................................................................................................... 8



Pre-Installed Knob Style.......................................................................................................... 12



Pre-Installed Post Style........................................................................................................... 14



Hook and Loop Style ............................................................................................................... 15

© 2019 Toyota Motor Sales, USA

T-SB-0158-18

Rev1

December 14, 2018

Page 3 of 15

Floor Mat Installation During PDS
Installation Procedure: Hook Style

1. Verify that the driver side, and if applicable, passenger side, and rear seat floor mats are for the
correct model and model year they are being installed in.
2. Attach the driver side, and if applicable, passenger side, and rear seat floor mats to the vehicle
carpet using the retention clips. Secure the mat by inserting the retention clip hooks through the
grommet holes.
Figure 1.

3
1

1
2
2
3

1

Correct Installation

2

Retention Clip

3

© 2019 Toyota Motor Sales, USA

Grom met

T-SB-0158-18

Rev1

December 14, 2018

Page 4 of 15

Floor Mat Installation During PDS
Installation Procedure: Hook Style (continued)

3. Verify proper installation.
NOTE
If applicable, do NOT remove the beige caution tag from the floor mat. ONLY the customer should
remove the caution tag.
Figure 2.

© 2019 Toyota Motor Sales, USA

T-SB-0158-18

Rev1

December 14, 2018

Page 5 of 15

Floor Mat Installation During PDS
Installation Procedure: Hook Style With Locking Clip

1. Verify that the driver side, and if applicable, passenger side, and rear seat floor mats are for the
correct model and model year they are being installed in.

2. Attach the retention clip to the floor by inserting the retention clip claws into the floor eyelet.
Figure 3.

1

B

5

B

4
A

B

A

3

2

1

Retention Clip

5

Cross-sectional Diagram

2

Front of Vehicle

A

Retention Clip Claw

3

Retention Clip Eyelet on Vehicle Floor

B

Locking Clip

4

Seat

© 2019 Toyota Motor Sales, USA

T-SB-0158-18

Rev1

December 14, 2018

Page 6 of 15

Floor Mat Installation During PDS
Installation Procedure: Hook Style With Locking Clip (continued)

3. To lock the retention clip in place, insert the
locking clip of the retention clip into the
designated hole.

Figure 4.

1

1

4. Align the floor mat grommets with the
retention clip hooks and attach the floor mat
grommets to the retention clip hooks.

Locking Clip

Figure 5.

1

2
3

1

Floor Mat Grommet

2

Retention Clip

3

Front

© 2019 Toyota Motor Sales, USA

T-SB-0158-18

Rev1

December 14, 2018

Page 7 of 15

Floor Mat Installation During PDS
Installation Procedure: Hook Style With Locking Clip (continued)

5. Verify proper installation.
NOTE
If applicable, do NOT remove the beige caution tag from the floor mat. ONLY the customer should
remove the caution tag.
Figure 6.

© 2019 Toyota Motor Sales, USA

T-SB-0158-18

Rev1

December 14, 2018

Page 8 of 15

Floor Mat Installation During PDS
Installation Procedure: Knob Style With Locking Clip