NHTSA ID Number: 10163233
Manufacturer Communication Number: SD-64-20124-US-0
TSB/Document Date: 2019-07-29
Summary
Bendix
? AutoVue FLC-20? Camera service data sheet update
SD-64-20124
®
Bendix™ AutoVue® FLC-20™ Camera
(See SD-61-4963 for the Bendix® Wingman® Fusion™ Active Safety System)
1.0 DESCRIPTION
The camera bracket
is attached to the
windshield, and the
camera snaps into it.
The Bendix™ AutoVue® FLC-20™ camera is a component
used in many Bendix safety systems, including:
• The AutoVue® Lane Departure Warning (LDW) System; and
(See Section 3.1)
• The Bendix® Wingman® Fusion™ Active Safety System.
For more information about the Bendix Wingman Fusion
System, see Service Data Sheet, SD‑61‑4963. For free
downloads of Service Data Sheets, visit the Bendix website
at bendix.com.
This document covers installation, troubleshooting, and
replacement for this camera.
Bendix safety technologies complement safe driving
practices. No commercial vehicle safety technology
replaces a skilled, alert driver exercising safe driving
techniques and proactive, comprehensive driver
training. Responsibility for the safe operation of the
vehicle remains with the driver at all times.
Radar Sensor
Figure 1 – Bendix™ AutoVue® FLC-20™ Camera
Road Lane Markings
Vehicle Equipped with the
Bendix® Wingman® Fusion™ System
iew
V
a
Ca
r
me
Front Bumper-Mounted
Radar Sensor
Detected Forward
Vehicle
RADAR Beam
Roof-mounted Telematics
Antenna
Bendix™ AutoVue® FLC-20™ Camera
Windshield-mounted Visible
Light Camera
NOT TO SCALE
Figure 2 – Operational View
1
1.1 GENERAL SAFETY GUIDELINES
WARNING! PLEASE READ AND FOLLOW THESE INSTRUCTIONS
GeneralINJURY
Safety Guidelines
TO AVOID 1.1
PERSONAL
OR DEATH:
When working on or around a vehicle, the following guidelines should be observed AT ALL TIMES:
▲ Park the vehicle on a level surface, apply the
parking brakes and always block the wheels.
Always wear personal protection equipment.
▲ Stop the engine and remove the ignition key
when working under or around the vehicle.
When working in the engine compartment,
the engine should be shut off and the ignition
key should be removed. Where circumstances
require that the engine be in operation, EXTREME
CAUTION should be used to prevent personal
injury resulting from contact with moving,
rotating, leaking, heated or electrically-charged
components.
▲ Do not attempt to install, remove, disassemble
or assemble a component until you have read,
and thoroughly understand, the recommended
procedures. Use only the proper tools and
observe all precautions pertaining to use of those
tools.
▲ If the work is being performed on the vehicle’s
air brake system, or any auxiliary pressurized air
systems, make certain to drain the air pressure
from all reservoirs before beginning ANY work
on the vehicle. If the vehicle is equipped with a
Bendix® AD-IS® air dryer system, a Bendix® DRM™
dryer reservoir module, or a Bendix® AD-9si® air
dryer, be sure to drain the purge reservoir.
▲ F o l l o w i n g t h e v e h i c l e m a n u f a c t u r e r ’s
recommended procedures, deactivate the
electrical system in a manner that safely removes
all electrical power from the vehicle.
▲ Never exceed manufacturer’s recommended
pressures.
▲ Never connect or disconnect a hose or line
containing pressure; it may whip and/or cause
hazardous airborne dust and dirt particles. Wear
eye protection. Slowly open connections with
care, and verify that no pressure is present. Never
remove a component or plug unless you are
certain all system pressure has been depleted.
▲ Use only genuine Bendix ® brand replacement
parts, components and kits. Replacement
hardware, tubing, hose, fittings, wiring, etc. must
be of equivalent size, type and strength as original
equipment and be designed specifically for such
applications and systems.
▲ Components with stripped threads or damaged
parts should be replaced rather than repaired.
Do not attempt repairs requiring machining or
welding unless specifically stated and approved
by the vehicle and component manufacturer.
▲ Prior to returning the vehicle to service, make
certain all components and systems are restored
to their proper operating condition.
▲ For vehicles with Automatic Traction Control
(ATC), the ATC function must be disabled (ATC
indicator lamp should be ON) prior to performing
any vehicle maintenance where one or more
wheels on a drive axle are lifted off the ground
and moving.
▲ The power MUST be temporarily disconnected
from the radar sensor whenever any tests USING
A DYNAMOMETER are conducted on a vehicle
equipped with a Bendix® Wingman® system.
▲ You should consult the vehicle manufacturer's operating and service manuals, and any related literature,
in conjunction with the Guidelines above.
Improper use of the Bendix® Wingman® Fusion™ Active
Safety System can result in a collision causing property
damage, serious injuries, or death. Be sure to read,
understand, and carefully follow the instructions in the
Operator’s Manual, BW2681.
Due to the inherent limitations of image recognition
technology, camera-based safety technology — on
rare occasions — may not be able to detect or may
misinterpret lane markings. At these times, alerts
may not occur, or erroneous alerts may occur.
2
Bendix safety technologies complement safe driving
practices. No commercial vehicle safety technology
replaces a skilled, alert driver exercising safe driving
techniques and proactive, comprehensive driver
training. Responsibility for the safe operation of the
vehicle remains with the driver at all times.
IMPORTANT: It is the responsibility of the driver to remain
vigilant and change driving practices depending on traffic
and road conditions.
How to identify if the vehicle has the Bendix® Wingman®
Fusion™ Active Safety System:
Look for the Bendix®
brand logo on the camera
label. (See Section 3.1
for how to remove the
camera from the bracket
to view the label.)
SERVICE DATA SHEET INDEX
1.0
Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
1.1
General Safety Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
2.0
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
2.1
Safety Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
2.2
Bendix™ Driver Interface Unit (DIU™) Lane Departure Warning System Icons . . . . . . . . . . . . 4
2.3
Camera Test Image . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2.4
Temporarily Disable the Lane Departure Warning (LDW) . . . . . . . . . . . . . . . . . . . . . . 6
2.5
Setting Diagnostic Trouble Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2.6
Bendix® ACom® Diagnostic Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2.7
Starting Bendix ACom Diagnostic Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2.8
Reading Diagnostic Trouble Codes (DTCs) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2.9
Diagnostic Trouble Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2.10
Table of DTCs and Service Action Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
2.11
Table of Service Action Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
2.12
Troubleshooting Diagnostic Trouble Codes: Power Supply . . . . . . . . . . . . . . . . . . . . 15
2.13
Serial Data (Private Communications) Troubleshooting Procedure . . . . . . . . . . . . . . . . 16
2.14
Power Troubleshooting Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
2.15
Communications (J1939) Test and Troubleshooting Procedures . . . . . . . . . . . . . . . . . . 16
2.16
Private Communications Network Test Procedure . . . . . . . . . . . . . . . . . . . . . . . . . 17
2.17
Troubleshooting Wiring Harnesses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
2.18
Clearing Diagnostic Trouble Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
3.0
Typical Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
3.1
Camera Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
3.2
Bracket Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
3.3
Dash Switches and Lamps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
3.4
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
3.5
Camera Interchangeability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
3.6
Important Note on Telematics Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Appendix A - SPN (Suspect Parameter Number) and FMI (Failure Mode Identifier) Codes to
Service Action Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Appendix B - Bendix® Wingman® Fusion™ System Component Schematic . . . . . . . . . . . . 26
Appendix C - Controller Configuration Changes . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Additional Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
3
2.0 TROUBLESHOOTING
2.1 SAFETY GUIDELINES
Read and follow the General Safety Guidelines shown
on page two of this document.
IMPORTANT
All vehicle Diagnostic Trouble Codes (DTCs)
related to the engine, transmission, instrument
cluster, engine cruise control, and Bendix® ABS,
ATC, or ESP® systems must first be resolved, with
no DTCs present during the vehicle operation
while in cruise control, before trying to resolve
camera DTCs.
IMPORTANT
System Problems. If a problem with the Bendix™
AutoVue® FLC-20™ camera is detected, it should be
serviced as soon as possible to restore full functionality.
2.2 BENDIX™ DRIVER INTERFACE
UNIT (DIU™) LANE DEPARTURE
WARNING SYSTEM ICONS
See Figure 3 and Figure 4. In the case of vehicles that
use a Bendix™ Driver Interface Unit (DIU™), the top right
corner of the display is used to show an icon. For other
OEM displays, see the vehicle manual to find the method
used to show the system status.
During Start-Up – System Busy
The first symbol shows when the Lane
Departure Warning (LDW) system is
initializing.
Camera Impaired
If the system experiences
problems detecting objects (for
example, due to sun-glare, a
dirty windshield, obstructions,
etc.), a full DIU screen message
will briefly be displayed.
The screen will revert to displaying
the icon shown, until the problem is
resolved.
Normal Operation
The LDW system is actively seeking
lane-markings.
The LDW system is actively tracking
lane-markings on both sides of the
current lane.
The system is actively tracking only
lane-markings on the left.
The system is actively tracking only
lane-markings on the right.
Figure 3 – Normal Bendix DIU Screens Showing
Lane Departure Warning (LDW) System Status
Diagnostic Trouble Code (DTC) Set
If no LDW status symbol is shown
– and the driver has not applied the
LDW disable switch – if there is no icon
present, this indicates that the system
has detected a DTC.
Figure 4 – Bendix DIU Screen Showing
LDW System Status
In these cases, the OE vehicle dash display will also alert
the operator that there is a DTC present.
4
2.3 CAMERA TEST IMAGE
Take a Test Image Using Latest Version of Bendix® ACom® Diagnostic Software
Troubleshooting a camera may be assisted by viewing a test image from the camera to ensure it is not blocked, or
has another problem.
•
Open Bendix® ACom® Diagnostic Software and select “FLC-20” from the opening page list, and the “Start with
ECU” button.
•
Select “Snapshot” from the choices.
1. Click “Read”. A camera snapshot is
taken. (Approximately 5 minutes.)
2. Inspect the image.
3. Save, if needed, using “Export”.
5
2.4 TEMPORARILY DISABLE THE
LANE DEPARTURE WARNING (LDW)
2.5 SETTING DIAGNOSTIC
TROUBLE CODES
To avoid erroneous LDW warnings in areas such as
construction zones – where the non-standard or overlapping
road markings present might cause false alerts – the
Bendix® Wingman® Fusion™ Active Safety System (Fusion)
has an enable/disable switch. The Bendix switch design or
a similar OEM switch may be used. See Figure 5.
If, during operation, the Bendix Wingman Fusion system
detects a problem with the Bendix™ AutoVue® FLC-20™
camera, a DTC will be set and – depending on the OEM –
the driver will be alerted on the dash display with an icon
or similar method. In these cases, some features of the
Fusion system will not be available.
Figure 5 – Example of an LDW
Enable/Disable Switch
If, for an extended period of time, the system detects that
the camera is blocked by dirt, snow, ice, etc., a DTC will
typically be set.
2.6 BENDIX® ACOM®
DIAGNOSTIC SOFTWARE
For vehicles that have the LDW switch hard-wired to the
SafetyDirect® by Bendix CVS Web Portal Processor, and a
functioning On Board Computer (OBC)/Telematics system:
The enable/disable switch used by the Lane Departure
Warning (LDW) system also functions – when depressed
for six (6) seconds – to activate a manual request to
transmit the last five seconds and next five seconds of
buffered video data.
Bendix® ACom® Diagnostic Software is a PC-based software
program available as a download from the Bendix website
(bendix.com). This software provides the technician with
access to all the available Electronic Control Unit (ECU)
diagnostic information and configuration capability. For
Fusion system diagnostics, use the current version of
Bendix ACom Diagnostic Software. See Figure 6.
Figure 6 – Bendix® ACom® Diagnostic Software
6
2.7 STARTING BENDIX® ACOM®
DIAGNOSTIC SOFTWARE
2.8 READING DIAGNOSTIC
TROUBLE CODES (DTCs)
The Bendix® ACom® Diagnostic Software can be started
from the desktop shortcut, or from the main Windows®
screen with “Start...Programs...Bendix...ACom Diagnostic
Software.” See Figure 7. To begin, the technician selects
“FLC-20” from the starter screen, then “Start with ECU”
from the Diagnostic Control panel.
If the system generates a Diagnostic Trouble Code (DTC),
where a lamp or icon is illuminated on the instrument
cluster, use a current version of ACom Diagnostic Software
to troubleshoot. Select “FLC-20” from the starter screen,
then “Start with ECU”. Click “DTC” to show the DTCs.
See Section 2.10 for a complete table showing DTCs and
troubleshooting information.
2.9 DIAGNOSTIC TROUBLE CODES (DTCs)
Use a J1939 detection software to find the DTC code(s)
and use the Table in Section 2.10 to find the service action
code to use. The service actions to take may then be found
in the Table shown in Section 2.11.
If the troubleshooting devices available to the technician
provide SPN (Suspect Parameter Number) and FMI (Failure
Mode Identifier) code combinations, refer to Appendix A.
Figure 7 – Starting Bendix® ACom® Diagnostic
Software
NOTE: When using ACom Diagnostic Software for the
first time, the service technician will be asked to select the
communication adapter for both the Bendix™ AutoVue®
FLC-20™ camera and Bendix® ABS and Stability Controllers.
While both controllers will use the same physical adapter,
the technician will need to indicate which communication
protocol to use for each. Once a successful connection
has been made, these steps will no longer be necessary.
The Bendix ACom Diagnostic Software for ABS User
Guide is available for download at bendix.com and
should be used as a reference to all functions of the
ACom service tool. See Figure 8.
Figure 8 – Bendix ACom Diagnostic Software –
Hardware Interface Screen
.
7
2.10 TABLE OF DIAGNOSTIC TROUBLE CODES (DTCs) AND SERVICE ACTION CODES
Look in the left column below for the DTC and find the Service Action Code to follow in Table 2 (Section 2.11).
Diagnostic Trouble Codes (DTCs),
Descriptions and Service Action Codes
DTC
1
Description
High Battery Voltage
B
Low Battery Voltage
Internal Error
A
Internal Error
B
Internal Error
A
Internal Error
Q
J1939 Bus Fault
M
Calibration not complete
Q
Internal Error
Internal Error
A
Image Processor software version error
I
Internal Error
A
Calibration data corrupt
Q
Internal Error
A
SPC Calibration not complete
Q
Internal Error
A
Dynamic Calibration out of range
Q
Dynamic Calibration not complete
Internal Error
A
Internal Error
Vehicle Calibration not complete
Q
Image Processor Calibration error
Internal Error
A
J1939: Vehicle controller message missing - LD
J1939: Brake controller message missing - VDC2
M
J1939: Engine controller message missing - CCVS1
J1939: Vehicle controller message missing - OEL
J1939: Vehicle controller signal error - OEL Turn Signal
J1939: Vehicle controller signal error - LD Right Turn
J1939: Vehicle controller signal error - LD Left Turn
N
J1939: Brake controller signal error - VDC2 Steering Wheel
J1939: Brake controller signal error - VDC2 Yaw Rate
J1939: Brake controller signal error - Lateral Accell
Private CAN: Error frame threshold exceeded
V
J1939: Brake controller signal error - EBC2 Wheel Speed
J1939: Brake controller signal error - EBC1 Brake Switch
N
J1939: Vehicle controller signal error - LCMD Right Turn
J1939: Vehicle controller signal error - LCMD Left Turn
Internal Error
A
Note: The system will not report newly active J1939 DTCs until the engine has been
running for 15 seconds. Do not attempt to diagnose J1939 DTCs without the engine running.
Call the Bendix Tech Team at 1‑800‑AIR‑BRAKE (1‑800‑247-2725), option 2 for troubleshooting assistance.
2
3-12
13
14-16
17
18
19
20
21-35
36
37-42
43
44-46
47
48-49
- [J2534 Pass-Thru Programmer] - TOPDON RLink J2534 is...
- [All-in-One OEM Reprogramming and Diagnostics] - When...
- [Tested, Trusted, and Proven for Accuracy] - TOPDON RLink...
- [One-Click Installation, Continuous Updates] - The exclusive...
- [Works with Windows Compatibility and OEM Software...
This product presentation was made with AAWP plugin.
If the PDF is very large, it may not load in the preview below.
Some older TSBs had multiple PDFs — visit the NHTSA Website to view all PDFs.
If the TSB PDF does not show, download or view it on the NHTSA Website.
Click on the (+) Plus Sign
Then Click on Associated Document(s)
Search NHTSA Database for Recalls
Search NHTSA Database for Vehicle Investigations
View Latest Vehicle Investigations
Search NHTSA Database for Vehicle Complaints
View Latest Vehicle Complaints
TSB/Document ID: SD-64-20124-US-0
Replacement Service Bulletin Number:
MFR Communication Date: 2019-05-20
MFR Internal Campaign ID/Software Version:
Communication Type: Service Bulletin/Repair Instructions
NHTSA Components: EQUIPMENT
MFR Component System:
MFR Component Subsystem:
Previous TSB | Next TSB |
- [Notice] When you receive a used escaner automotriz device, it may be a customer return resold by Amazon without inspection. You can exchange it for a new one through Amazon. As this situation is unavoidable, we sincerely apologize. For any issues, contacting us via Amazon's "Messages" is the best way, and we’ll provide a solution within 24 hours. THINKSCAN 689BT Can Be Used Immediately After It is Turned On, Without Complicated Registration Process, Which is More Convenient & Quick.
- [Good News] THINKSCAN 689BT is the most competitive automotive scan tool to date, offering wireless updates with no subscription fees(valued 500Buc.ks) . With all the features of THINKTOOL PD8,PRO, built on Android 10 platform with 4-core CPU, 4GB RAM
and 64GB ROM, serving up to 5X faster than older MAX/MINI/PLUS vehicle scanners escaner automotriz, no more slow and delayed feedbacks, it's time to update your garage tool. - [Big Money Saver] Premium THINKSCAN 689BT Wireless Diagnostic Scanner Escaner Automotriz, save up to 400USD per year, includes all useful features: Full bi-directional controls, ECU coding, 34+ services, OEM all system diagnostics, Worldwide vehicles coverage, CAN FD & DoIP, FCA AutoAuth（The 689BT only provides a login and purchase portal, and users are required to register for an FCA account and pay a membership fee in order to perform the relevant automotive diagnostics)
- [3000+ Active Tests]Active testing is one of the most useful features in automotive maintenance and greatly improves mechanic efficiency. THINKCAR 689BT bidirectional scanner can send action commends to vehicle sub-systems or components for active test without using vehicle controls. It can perform various tests such as: EVAP Test, Fuel Trim Reset, Injector Buzz Test, Window/ Mirror/ Door Lock Test, Pump and Value Tests, etc. Get functions from "Diagnose>Car Model>System>Active Test".
- [Hot Advanced Features] 689BT bidirectional tool newly adds ECU Coding, Power Balance, Flash Hidden Functions, Reset Adaptive Data, Match Replaced Components, Customize OE-Settings. Such as: 1. changing the color of interior lights 2. switching on/off the auto hold, 3. customizing dash kits 4. activating the auto side mirror folding function 5. disables auto start-stop. Note: Coding functions vary by model&year.
- 【Warm Tips】Wired THINKSCAN 689 is connected through a detachable OBDII cable, and we also have added OBD2 Extension Cable (about 60 cm/2 feet) as g ift, enabling customers handling vehicle repairs with ease. Just click "Bundles Item" above to get it. Note: FCA AutoAuth is a third-party service, additional cost may be required.
- 【Professional Car Diagnostic Tool】Tired of renew fees? Thinkscan 689 scanner provides dealer-level advanced functions without annual fees for auto mechanics and repair shops. 34+ Services, 3000+ Active Test, ECU Coding, 140+ Brands Coverage, FCA AutoAuth, CANFD&DOIP Protocol, Component Matching, Power Balance, V.A.G Guided, Compatible with Google Chrome integration, etc. With strong hardware backing, 64G Memory, Android 10, 4-core processors, and 4150mAh battery. Thinkscan 689 brings you the best as your daily business helper and never lets you drop the ball!
- 【Over 34 Reset Service, Adaptation + Relearn + Calibration + Initialization + Matching】Made for workshops, Thinkscan 689 scanner provides 34+ services for worldwide vehicles: such as Gear/SAS/EPB/TPMS/D.P.F/I.M.M.O/BMS/ETS/Oil/Brake/AFS/GEARBOX/SUNROOF/SUS Reset, ABS Bleed, Injector coding, etc. Warm tips: Compatibility may vary on vehicles' model and year, please contact seller before purchase to make sure it works well on your cars.
- 【Real Active Test】Thinkscan 689 scan tool features over 3000+ full bi-directional control ability, to send commands to vehicle’s systems/components, to verify system input/output without using the vehicle's controls, e.g. turn on the radiator fan, modulate the throttle, open/close windows, operate mirrors, Injector Buz Test, turn on interior&exterior lights, sound horn, test door lock actuators, turn on/off front/rear side ACM Solenoid, Vehicle level position calibration, Wheel Speed Sensor Supply.
- 【Comprehensive Solutions with Advanced Features】Take your vehicle customization to the next level with the Thinkscan 689's advanced ECU coding capabilities. This scan tool provides power balance, PMI, unlock more new features and enhance performance by activating dormant functions, customizing OE settings, matching replaced components, and reprogramming adaptive data to elevate your driving experience. Note: Compatibility varies by car models, please check before order.
- 【Powerful Bidirectional Control -- Active Test】Good News! The THINKSCAN 662 obd2 scanner has bidirectional control function,which is the most popular feature among mechanics.This function is mainly used to test whether the executing components in the electronic control system can work normally,By requesting information from the vehicle's ECU or sending commands to the ECU module to execute commands and identify maintenance status,quickly locate the cause of the fault.Such as ABS,Fuel Injectors,Adjusting Throttle,Coolant Fans,Radiator Fans,Coolant Pumps,EV.AP Test, Fuel Trim Reset,Injector Buzz Test,Pump/ Value Test,etc. Effectively shorten diagnosis time and reduce diagnosis costs.
- 【Unlock Pro-Level Diagnostics With Half Costs】 THINKSCAN 662 obd2 scanner diagnostic tool Delivers Premium Scanning Power for Half the Price! The OBD2 scanner can handle common issues with ECM,TCM,ABS,SRS. It can easily read and clear fault codes, analyze data streams, and ensure quick identification of problems. THINKSCAN 662 bidirectional scan tool has 12 practical reset functions, including Airbag Reset,ABS Bleeding,BMS,Brake Reset, D.P.F,Throttle Adaptation,Injector Coding,OIL Reset,steering angle Reset,Gearbox,TPMS,and more. The car scanner diagnostic tool very suitable for DIY enthusiasts, car repair technicians, and small and medium-sized repair shops.
- 【Multi Functional Intelligent Car Scanner Diagnostic Tool】 Automatic VIN + Real-time Data + DTC Lookup + Historical Diagnostic Records: This OBD2 scanner features auto serch technology, allowing for car recognition without the need for manual input. The real-time data of the car ECU is read and displayed in the form of text or a 4-in-1 merged waveform chart. You can save, share, print or send the entire inspection report via email for analysis. Historical diagnostic reports help you quickly identify vehicle issues and understand the condition of the vehicle. The built-in 'feedback' module provides customized repair Operation recommendations from our certified professionals.
- 【Upgraded Hardware + Ergonomically Engineered】 THINKSCAN 662 OBD2 scanner has a friendly combination of touch screen and physical buttons with an ergonomic appearance for comfortable use.Experience 2x faster scans and 50% longer lifespan vs standard models.This scanner para autos boast a 4-core 1.8GHz CPU,6.2-inch HD touch screen,2GB RAM + 32GB ROM storage capacity,a long-lasting 4150mAh battery,Android 8 ensures lightning-fast bootup and processing.The scanner is robust with rubberized protection that you can store and use in the trunk or garage.Whether you are engaged in Home car maintenance or road rescue car repair,this car scanner can help you perfectly solve car problems.
- 【Effortless Setup & Scanning - Intuitive for All Skill Levels】No More Complicated Scanners! The User Interface is as User-Friendly as THINKCAR 689BT! Truly Plug-and-Play,The downward sliding setup shortcut portal and drawer function shortcut portal make you use this scan tool as easy as using your own cell phone.The car scanner supports setup screenshot,screen recording,volume adjustment,this scan tool includes product e-manuals,instructional videos,and fault code libraries,users can check the usage guide,perfect for DIY car owners,Maintenance technician.If your father,husband,brother,boyfriend enjoys car repairs,THINKSCAN 662 is a great gift choice, and it has amazing family value.
This product presentation was made with AAWP plugin.
Last update on 2026-06-05 / Affiliate links / Images from Amazon Product Advertising API