Oggetto:
Data:
Pagine

L636A.04.19

Official After-Sales Network
Infotainment update
15 Febbraio 2019
10

10. From “Guided Functions” of the ECU 5F select the
function “5F – Read identification data”. Check that in
“Information Parameters” the following information
are shown:

II.



Record number: V03935290AH



Record version: 0012

Fault memory deletion:

11. Select the “Special Functions” card and then “Erase
fault memory - overall system” in order to delete all
stored faults.

Rev.00

The complete guide for deleting faults is available in
the workshop manual, chapter “10.00.B-Deleting the
data in the fault memory of control units”.
12. Go back to the “Block diagram” card and select “Read
all fault memories” from one of the vehicle’s control
units in order to update the display of the faults present after deletion.

III.

Installation confirmation:

After updating the 5F and clearing the fault memories,
"B201A00: Checking the Software Version" may occur.
13. If this error occurs, perform the function that is attached to the "Test Plan": "5F -SVM - Reset fault
memory". Click on "Perform Test" to perform the
function.

The procedures and information published herein are strictly confidential and are intended exclusively for recognized professionals and
persons who are authorized to receive said information. All copyrights are the property of Automobili Lamborghini S.p.A. pursuant to
copyright law. The company reserves the right to make updates and modifications as required. The reprinting, reproduction, distribution to
unauthorized persons and/or to third parties, and the partial or complete translation of the material contained herein are prohibited without
the express written consent of Automobili Lamborghini S.p.A.
doc. no.: L/V6_M06 Rev.[05]

6/10

L636A.04.19

A:
Oggetto:
Data:
Pagine

Official After-Sales Network
Infotainment update
15 Febbraio 2019
10

14. Wait for the end of the automatic control procedure.

IV.

Fault memory deletion:

17. Select the “Special Functions” card and then “Erase
fault memory - overall system” in order to delete all
stored faults.

15. Click on “Done/Continue” to confirm the installation.

The complete guide for deleting faults is available in
the workshop manual, chapter “10.00.B-Deleting the
data in the fault memory of control units”.
18. Go back to the “Block diagram” card and select “Read
all fault memories” from one of the vehicle’s control
units in order to update the display of the faults present after deletion.

16. Click then on “Done/Continue” to end the procedure.

Rev.00

The procedures and information published herein are strictly confidential and are intended exclusively for recognized professionals and
persons who are authorized to receive said information. All copyrights are the property of Automobili Lamborghini S.p.A. pursuant to
copyright law. The company reserves the right to make updates and modifications as required. The reprinting, reproduction, distribution to
unauthorized persons and/or to third parties, and the partial or complete translation of the material contained herein are prohibited without
the express written consent of Automobili Lamborghini S.p.A.
doc. no.: L/V6_M06 Rev.[05]

7/10

L636A.04.19

A:
Oggetto:
Data:
Pagine

Official After-Sales Network
Infotainment update
15 Febbraio 2019
10

NOTA:
At the end of the above procedures, a reboot of the ECU
5F may be necessary, which can be performed with a long
pressure of the ECU 5F knob.

ii.

If an error is displayed that regards the hardware
interface, and the "connection to vehicle" and "key
state" icons appear as shown in the figure below:

-

Click “Cancel”;
Repeat installation of the interface VAS5054 for
the instructions in procedure (*)“VCI Manager
v2.0”, selecting the right-hand “Extras” menu in
ODIS and clicking on the “Diagnostic interface”
button.

iii.

If one of the following connection errors is displayed like in the following example screenshots:

/* Diagnosis protocol saving */
19. Save the Diagnostic protocol as described in the chapter “10.00.H-Saving the diagnostic protocol” when
the procedure described in this document is completed.

IMPORTANT:
The Diagnostic Protocol must be attached to the Corresponding Warranty Request (to enter the request on the
web portal, refer to the W.Claim manual which you can
consult in the Warranty section of the portal).
Trouble shooting:
i.

Rev.00

If the following error screen is displayed, abort the
guided function by clicking on “Cancel Test” and
contact Technical Support.

-

It is not possible to connect to the central server;
check that your laptop is correctly connected to
the Internet and retry by clicking on “Yes” or
“Done/continue”, as appropriate.

The procedures and information published herein are strictly confidential and are intended exclusively for recognized professionals and
persons who are authorized to receive said information. All copyrights are the property of Automobili Lamborghini S.p.A. pursuant to
copyright law. The company reserves the right to make updates and modifications as required. The reprinting, reproduction, distribution to
unauthorized persons and/or to third parties, and the partial or complete translation of the material contained herein are prohibited without
the express written consent of Automobili Lamborghini S.p.A.
doc. no.: L/V6_M06 Rev.[05]

8/10

A:
Oggetto:
Data:
Pagine

L636A.04.19

Official After-Sales Network
Infotainment update
15 Febbraio 2019
10

v.

If the authentication error as shown in the following
screenshot is displayed (error code: ODS1007E):
-

Ensure you have a valid GeKo user account

-

Ensure that the “GeKo” label is printed on the token you are using
Ensure you have entered the correct password
Click on “Cancel” and run the application test
(see document
“ODIS_ControlloConnessione_Server_SVM_2.0”
(*)
).

-

vi.
iv.

If the connection is dropped during the course of
the target/actual comparison during the SVM procedure:
-

It is not possible to connect to the central server;
check that your laptop is correctly connected to
the Internet and retry by clicking on “1”.

If the infrastructure error as shown in the following
screenshot is displayed (error code: ODS9212E):
-

-

Rev.00

Ensure you have a valid GeKo user account
Ensure that the “GeKo” label is printed on the
token you are using
Check that the Internet is set in ODIS settings
and not CPN (see document “Setup_Iniziale_ODIS_2.0” (*))
Click on “Cancel” and run the application test
(see document
“ODIS_ControlloConnessione_Server_SVM_2.
0” (*)).

The procedures and information published herein are strictly confidential and are intended exclusively for recognized professionals and
persons who are authorized to receive said information. All copyrights are the property of Automobili Lamborghini S.p.A. pursuant to
copyright law. The company reserves the right to make updates and modifications as required. The reprinting, reproduction, distribution to
unauthorized persons and/or to third parties, and the partial or complete translation of the material contained herein are prohibited without
the express written consent of Automobili Lamborghini S.p.A.
doc. no.: L/V6_M06 Rev.[05]

9/10

A:
Oggetto:
Data:
Pagine

L636A.04.19

Official After-Sales Network
Infotainment update
15 Febbraio 2019
10

Lamborghini web portal, in the corresponding ODIS section.

IMPORTANT:
The documents which must be provided with the warranty
request are:

vii.

If the same error type should reoccur during the
application test, try the following procedure:
-

Exit ODIS
Browse to the folder C:\Program Files
(x86)\Offboard_Diagnostic_Information_Syst
em_Service\.automatic_sessions on your diagnostic laptop

-

Delete the only file which will be in the older
Restart ODIS Service, ensuring that:

-

Produced Repair Order

-

Saved Diagnostic Protocol

Failure to follow these procedures could lead to the request being rejected.

1. You have a network connection
2. The ODIS connection is set to Internet
-

Run the connection test again, and perform the
SVM again with your GeKo Token.

IMPORTANT:
If the error occurs again, repeat the procedure and try
with a second GeKo token, if available.

NOTE.(*)
All ODIS technical documentation can be viewed on the

Rev.00

The procedures and information published herein are strictly confidential and are intended exclusively for recognized professionals and
persons who are authorized to receive said information. All copyrights are the property of Automobili Lamborghini S.p.A. pursuant to
copyright law. The company reserves the right to make updates and modifications as required. The reprinting, reproduction, distribution to
unauthorized persons and/or to third parties, and the partial or complete translation of the material contained herein are prohibited without
the express written consent of Automobili Lamborghini S.p.A.
doc. no.: L/V6_M06 Rev.[05]

10/10