doc. nr: L/V6_M06 Rev.[05]

8/17

L636A.04.18

To:
Subject:
Date:
Pages

Official After Sales Network
Update ECU 5F
21 February 2019
17

15. Wait the automatic procedure, DO NOT interrupt the
read manifest file process by clicking cancel update.

16. The files to be installed will be listed in the screen,
scroll with the main knob through the items displayed
in the ECU 5F, until you select “Start Update”.

17. Start the software update procedure selecting "Start
Update".

IMPORTANT:
The update procedure must not be cancelled under any
circumstances.
18. Wait for the update procedure.

Rev.06

The information and procedures published below are strictly confidential and intended exclusively for authorized operators and individuals. All copyrights are the property of Automobili Lamborghini S.p.A based on copyright law. The company reserves the right to make
updates and modifications. The reprinting, reproduction, forwarding to unauthorized people and/or to third parties and partial or entire
translation thereof are prohibited without written authorization from Automobili Lamborghini S.p.A.
doc. nr: L/V6_M06 Rev.[05]

9/17

L636A.04.18

To:
Subject:
Date:
Pages

Official After Sales Network
Update ECU 5F
21 February 2019
17

19. When the software update is complete, the ECU 5F
display is restarted.

22. Click quit to exit the engineering menu.

23. Turn the ignition OFF and back ON.
20. Wait the automatic procedure, DO NOT interrupt the
read manifest file process by clicking cancel update.

24. Move on your laptop and check in ODIS that the update was successful. From the Guided functions of the
5F run the function “5F - Read identification data”
Check that the displayed software version is correct,
as indicated in the table presented in step 5.

21. When the ECU 5F restarts, the “Update Summary”
file will be displayed, scroll down and click “Resume”.
You can now unplug the USB memory stick.

Rev.06

The information and procedures published below are strictly confidential and intended exclusively for authorized operators and individuals. All copyrights are the property of Automobili Lamborghini S.p.A based on copyright law. The company reserves the right to make
updates and modifications. The reprinting, reproduction, forwarding to unauthorized people and/or to third parties and partial or entire
translation thereof are prohibited without written authorization from Automobili Lamborghini S.p.A.
doc. nr: L/V6_M06 Rev.[05]

10/17

L636A.04.18

To:
Subject:
Date:
Pages

Official After Sales Network
Update ECU 5F
21 February 2019
17

C. ECU 5F ZDC Update:
Follow the procedure in the workshop manual related to
the "Implementation of an SVM code".

IMPORTANT:

Improper use of this function can cause damage to
the electronic control units.

27. Type the campaign code “L636A0418” in the appropriate space on the upper right-hand and click on
"Adopt".

L636A0418

25. To start the procedure for executing an SVM code, select the "Special functions" tab in ODIS.

28. The entered SVM code is re-displayed on the dialog
screen. If the entered code is correct, click on "Yes" to
confirm, otherwise select “No” and restart the SVM
procedure.
29. Wait the data acquisition from all the control units.
This operation takes a few minutes.

26. Click on the function "SVM- Direct input: SVM code
for problem-related update" and then on "Perform
test”.

30. To perform the SVM function and access the Lamborghini servers it is necessary to have a valid GeKo account. Make sure that the diagnostic laptop is connected correctly to internet. Enter your GeKo username in
the "User name" field and pin 1324 + the 6-digit code
currently displayed on the GeKo token in the "Password" field.

Rev.06

The information and procedures published below are strictly confidential and intended exclusively for authorized operators and individuals. All copyrights are the property of Automobili Lamborghini S.p.A based on copyright law. The company reserves the right to make
updates and modifications. The reprinting, reproduction, forwarding to unauthorized people and/or to third parties and partial or entire
translation thereof are prohibited without written authorization from Automobili Lamborghini S.p.A.
doc. nr: L/V6_M06 Rev.[05]

11/17

To:
Subject:
Date:
Pages

L636A.04.18

Official After Sales Network
Update ECU 5F
21 February 2019
17

Click “Adopt” to confirm.
31. The SVM function will automatically continue with
the identification of the ECUs in the vehicle.

32. In the SVM procedure it may be necessary to perform
one or more of the following operations:


Coding;



Parametrization;



Calibration.

33. Click "Done / Continue" to conclude the update procedure for the ECU 5F.

34. From the “Guided functions” of the ECU 5F run the
function “5F- Read identification data”. Check that the
displayed ZDC version is the “0003” with index “AH”.

To perform these actions, it is usually necessary to
click "Done / Continue" where required and follow the
instructions directly reported in the ODIS dialog
screens.

Rev.06

The information and procedures published below are strictly confidential and intended exclusively for authorized operators and individuals. All copyrights are the property of Automobili Lamborghini S.p.A based on copyright law. The company reserves the right to make
updates and modifications. The reprinting, reproduction, forwarding to unauthorized people and/or to third parties and partial or entire
translation thereof are prohibited without written authorization from Automobili Lamborghini S.p.A.
doc. nr: L/V6_M06 Rev.[05]

12/17

L636A.04.18

To:
Subject:
Date:
Pages

Official After Sales Network
Update ECU 5F
21 February 2019
17

D. Erase fault memories:
35. Go back to the “Special functions” tab and select
“Erase fault memory – overall system” to clear all the
stored faults.

E. Confirmation of installation:
After the update of the 5F and the erase fault memories,
the error “B201A00: Checking software version management” could occur.
37. If this error occurs, run the function that you find attached to the test plan: “5F –SVM – Reset fault
memory”. Click “Perform test” to run the function.

The complete guide in order to erase all fault memories is available in the workshop manual, chapter
10.00.Deleting the data in the fault memory of control units.
36. Go back to the “Block diagram” tab and select “Read
all fault memories” from one of the ECUs of the vehicle.

38. Wait the end of the automatic checking procedure.

39. Click “Done/Continue” to confirm the installation
change.

Rev.06

The information and procedures published below are strictly confidential and intended exclusively for authorized operators and individuals. All copyrights are the property of Automobili Lamborghini S.p.A based on copyright law. The company reserves the right to make
updates and modifications. The reprinting, reproduction, forwarding to unauthorized people and/or to third parties and partial or entire
translation thereof are prohibited without written authorization from Automobili Lamborghini S.p.A.
doc. nr: L/V6_M06 Rev.[05]

13/17

L636A.04.18

To:
Subject:
Date:
Pages

Official After Sales Network
Update ECU 5F
21 February 2019
17

The complete guide in order to erase all fault memories is available in the workshop manual, chapter
10.00.Deleting the data in the fault memory of control units.
42. Go back to the “Block diagram” tab and select “Read
all fault memories” from one of the ECUs of the vehicle.

40. Click “Done/Continue” to end the procedure.

NOTE:

F. Erase fault memories:

At the end of the procedures indicated, it may be necessary
to reboot the ECU 5F, which can be carried out with a
long press of the ECU 5F main knob.

41. Go back to the “Special functions” tab and select
“Erase fault memory – overall system” to clear all the
stored faults.
/* Diagnosis protocol saving */
43. At the end of software updates, save the diagnostic
protocol as described in chapter 10.00.ODIS Saving
the diagnostic protocol.

IMPORTANT:

The diagnosis protocol has to be attached to the related Warranty Claim (in order to insert the claim on
the Web Portal, please refer to Warranty Claim
Manual you can find under the Portal, Warranty section).

Rev.06

The information and procedures published below are strictly confidential and intended exclusively for authorized operators and individuals. All copyrights are the property of Automobili Lamborghini S.p.A based on copyright law. The company reserves the right to make
updates and modifications. The reprinting, reproduction, forwarding to unauthorized people and/or to third parties and partial or entire
translation thereof are prohibited without written authorization from Automobili Lamborghini S.p.A.
doc. nr: L/V6_M06 Rev.[05]

14/17

To:
Subject:
Date:
Pages

L636A.04.18

Official After Sales Network
Update ECU 5F
21 February 2019
17

the diagnosis laptop is properly connected to
the internet network and retry clicking “Yes”
or “Done/Continue”.

Trouble shooting:
i.

If the following error page is shown, you shall
abort the procedure clicking on “Cancel Test” and
contact the Technical Support.

ii.

If the error message regarding the VAS5054 interface and the two icons for status of on board connection and key ON are shown as in the picture
below:
-

Click “Cancel”;
Repeat the VAS6154 HW interface installation following the procedure (*) “VCI Manager v2.0”, by entering in the menu “Extras” on
the right side and clicking on “Diagnostic interface”.

iv.

If the loss of connection happens during the target/actual comparison during SVM procedure:
-

iii.

If one of the connection error screens is shown as
in the pictures below:
-

Rev.06

It is not possible to connect to central server,
check the working connection of internet and
retry by clicking “1”.

It is not possible to establish a connection with
the central server. Please check carefully that
The information and procedures published below are strictly confidential and intended exclusively for authorized operators and individuals. All copyrights are the property of Automobili Lamborghini S.p.A based on copyright law. The company reserves the right to make
updates and modifications. The reprinting, reproduction, forwarding to unauthorized people and/or to third parties and partial or entire
translation thereof are prohibited without written authorization from Automobili Lamborghini S.p.A.
doc. nr: L/V6_M06 Rev.[05]

15/17

L636A.04.18

To:
Subject:
Date:
Pages

Official After Sales Network
Update ECU 5F
21 February 2019
17

vi.

If the infrastructure error message is shown as in
the picture below (error code: ODS9212E):
-

-

v.

be sure that your Geko account is valid
be sure that the label “Geko” is written on the
token that you are using for the authentication
verify in ODIS settings you have “Internet”
instead
of
“CPN”
(see
document
“ODIS_Initial_Setup_2.0” (*))
click on Cancel and perform the application
test (see document
“ODIS_Checking_ConnectionServer_SVM_2
.0” (*)).

If the incorrect identification message is shown as
in the picture below (error code: ODS1007E):
-

be sure that your Geko account is valid;

-

be sure that the label “Geko” is written on
the token that you are using for the authentication;

-

be sure the Password inserted is correct;

-

click on Cancel and perform the application test (see document
“ODIS_Checking_ConnectionServer_SV
M_2.0” (*)).
vii.

If the same error is present during the application
test, try the following procedure:
-

-

quit ODIS;
Enter
the
folder
C:\Program
Files
(x86)\Offboard_Diagnostic_Information_Syst
em_Service\.automatic_sessions on your diagnosis laptop;
delete the only file present in that folder.
re-Start ODIS Service under following conditions:
1. Network connection available;
2. ODIS connection set on “Internet”;

-

Rev.06

Retry the application test and the SVM with
your GeKO Token.

The information and procedures published below are strictly confidential and intended exclusively for authorized operators and individuals. All copyrights are the property of Automobili Lamborghini S.p.A based on copyright law. The company reserves the right to make
updates and modifications. The reprinting, reproduction, forwarding to unauthorized people and/or to third parties and partial or entire
translation thereof are prohibited without written authorization from Automobili Lamborghini S.p.A.
doc. nr: L/V6_M06 Rev.[05]

16/17

L636A.04.18

viii.

To:
Subject:
Date:
Pages

Official After Sales Network
Update ECU 5F
21 February 2019
17

In the event that the following error occurs, it is
necessary to follow the instructions given in
BI.25.18, which can be downloaded from the
Lamborghini HUB.

IMPORTANT REMARKS:
The documents to be mandatory attached to the claim are:
-

Job order done;

-

Diagnosis Protocol saved.

Failure to follow the procedures may lead to the rejection of the request.

IMPORTANT:
In the case an error is still present, retry the procedure
with a second GeKO token, if available.

NOTE.(*)
ODIS technical documentation can be retrieved on the
Lamborghini web portal, under ODIS section.

Rev.06

The information and procedures published below are strictly confidential and intended exclusively for authorized operators and individuals. All copyrights are the property of Automobili Lamborghini S.p.A based on copyright law. The company reserves the right to make
updates and modifications. The reprinting, reproduction, forwarding to unauthorized people and/or to third parties and partial or entire
translation thereof are prohibited without written authorization from Automobili Lamborghini S.p.A.
doc. nr: L/V6_M06 Rev.[05]

17/17