TIS Service Bulletin

Page 1 of 3

SI B66 01 19
Drivers Assistance, Remote Control Systems

April 2019
Technical Service

CHECK CONTROL MESSAGE PARKING ASSISTANCE
RESTRICTED
This Service Information bulletin replaces SI B66 01 19 dated April 2019
What’s New:
• Deleted all references to car wash

MODEL
G05 (X5 Sports Activity
G07 (X7 SAV)
Vehicle)
G20 (3 Series Sedan)

G14 (8 Series
Convertible)

G15 (8 Series Coupe)

G29 (Z4 Roadster)

SITUATION
Upon activation of the Park Distance Control (PDC) or Parking Assistant, a Check Control Message (CCM)
“Restricted parking assistance” may be displayed
Only vehicles equipped with any of these option codes are affected:


0508 Park Distance Control (PDC); available on all models either as standard or optional equipment



05DM Parking Assistant, available only on G29 as optional equipment



05DN Parking Assistant Plus, available on all models except G29

The CCM will not reset itself. It will be displayed each time the PDC is activated, even though the fault
is no longer present.

CAUSE
Ultrasonic sensors, and/or software error in PDC control module.
The following faults are logged based on the sequence of occurrence:
1. 0x803207 - sensor system: Extraneous noise detected
2. 0x803206 - sensor system: Blindness detected

CORRECTION


Run diagnosis with ISTA
— If the faults are stored, but not currently active, follow SI B66 04 19.
— If the faults are currently active (permanent), proceed with the steps outlined below in this SI.

https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/504... 5/1/2019

TIS Service Bulletin

Page 2 of 3



Work through the corresponding test module if necessary



Program/encode the vehicle using ISTA 4.15.2x or higher
— Target Integration level (I-level) S18A 18-11-549, or higher

Always connect a BMW-approved battery charger/power supply (SIB04 23 10) when performing
programming.
For information on programming and coding with ISTA, refer to CenterNet / TIS / Technical Documentation /
Programming and Diagnostics / Programming Documentation
Note: Parts replacement will not provide a solution to this situation.

WARRANTY INFORMATION
Covered under the terms of the BMW New Vehicle Limited Warranty for Passenger Cars and Light Trucks.

Defect Code:

6633000200

Control unit, parking maneuvering
assistant PMA software error / internal
device fault

Labor Operation:

Labor Allowance:

Description:

00 00 006

Refer to AIR/KSD2

Performing “vehicle test” (with vehicle
diagnosis system – checking faults) (Main
work)

Refer to AIR/KSD2

Performing “vehicle test” (with vehicle
diagnosis system – checking faults) (Plus
work)

Refer to AIR/KSD2

Connect an approved battery charger/power
supply (indicated in KSD2 as “Charging
battery”)

Refer to AIR/KSD2

Programming/encoding control unit(s)

Or:
00 00 556
And:
61 21 528:
And:
61 00 730

If you are using a Main labor code for another repair, use the Plus code labor operation 00 00 556 instead of 00
00 006.
During the same workshop visit, if a vehicle also requires another Technical Campaign or repair that also
includes programming and encoding the control modules, the programming procedure may only be
invoiced one time.
Programming and Encoding - Vehicle Control Units
A. The programming procedure automatically reprograms and encodes all vehicle control modules which do
not have the latest software i-level. If one or more control module failures occur “during” this programming

https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/504... 5/1/2019

TIS Service Bulletin

Page 3 of 3

procedure:
• Please claim this “consequential” control module-related repair work under the defect code listed in this
bulletin with the applicable AIR/KSD2 labor operations.
Please explain this additional work (The why and what) on the repair order and in the claim comments section.
B. For control module failures that occurred “prior” to performing this programming procedure:
• When “covered” under an applicable limited warranty, claim this control module-related repair work using the
applicable defect code and labor operations (including diagnosis) in AIR/KSD2.
*IMPORTANT:
As with all work that is reimbursed by BMW, the repair order, time recording, and record keeping requirements
outlined in the Warranty Policy and Procedures Manual must be strictly observed. Quality Certification I
payments are subject to audit.
[ Copyright ©2019 BMW of North America, Inc. ]

https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/504... 5/1/2019