1/7/2019

LTB01009NAS7 - InControl® Touch Pro™ Features May Not Function As Expected | TOPIx

LT B 0 1 0 0 9 N A S 7

TECHNICAL BULLETIN
02 JAN 2019

© Jaguar Land Rover North America, LLC
NOTE: The information in Technical Bulletins is intended for use by trained, professional Technicians
with the knowledge, tools, and equipment required to do the job properly and safely. It informs these
Technicians of conditions that may occur on some vehicles, or provides information that could assist in
proper vehicle service. The procedures should not be performed by 'do-it-yourselfers'. If you are not a
Retailer, do not assume that a condition described affects your vehicle. Contact an authorized Land
Rover service facility to determine whether this bulletin applies to a specific vehicle.

I N F O R M AT I O N

This reissue replaces all previous versions. Please destroy all previous versions.
Changes are highlighted in blue

SECTION:
415-01:

S U B J E C T/ C O N C E R N :
InControl® Touch Pro™ Features May Not Function As Expected

AFFECTED VEHICLE RANGE:
MODEL:

MODEL YEAR:

https://topix.landrover.jlrext.com/topix/content/document/view?id=949249

VIN:

APPLICABILITY:
1/18

1/7/2019

LTB01009NAS7 - InControl® Touch Pro™ Features May Not Function As Expected | TOPIx

MODEL:

MODEL YEAR:

VIN:

APPLICABILITY:

Discovery Sport (LC)

2017

634012-721747

Vehicles With: InControl Touch Pro

Range Rover Evoque (LV)

2016-2017

166843-267152

Vehicles With: InControl Touch Pro

MARKETS:
NORTH AMERICA

CONDITION SUMMARY:

A major part of this update is to the of the single-screen InControl® Touch Pro™ system, which
will change to match that of the InControl® Touch Pro Duo™ system. The customer must be
aware that after this software update is finished, they will be required to sign back in to any
vehicle applications that were being used prior to the software update.
SITUATION:
In response to customer feedback on the performance of the InControl® Touch Pro™ system, Jaguar
Land Rover has developed a software upgrade designed to enhance the robustness of a range of
system features and functions.
CAUSE:
These may be caused by a software issue.
ACTION:
Should a Customer express any of the concerns listed in the software tab of the TOPIx vehicle
summary pop-up, accessible from TOPIx after entering the VIN, follow the Diagnostic Procedure
below.

PA RTS :
No Parts Required

https://topix.landrover.jlrext.com/topix/content/document/view?id=949249

2/18

1/7/2019

LTB01009NAS7 - InControl® Touch Pro™ Features May Not Function As Expected | TOPIx

TOOLS:



Jaguar Land
Rover-approved
Midtronics battery
power supply



Jaguar Land
Rover-approved
diagnostic
equipment with
latest SDD
Software
Management Pack
and InControl©
Touch Pro™
Software

DTSE9G2/32GB
Jaguar Land
Rover-approved
USB memory
device

WARRANT Y:

NOTES:
Repair procedures are under constant review, and therefore times are subject to change;
those quoted here must be taken as guidance only. Always refer to JLR claims submission
system to obtain the latest repair time.
The JLR Claims Submission System requires the use of causal part numbers. Labor only claims
must show the causal part number with a quantity of zero.
DESCRIPTION

SRO

TIME
(HOURS)

CONDITION
CODE

CAUSAL
PART

Infotainment Master Controller (IMC) - Update
ECU

85.87.20

0.5

42

LR091126

Infotainment Slave Controller (ISC) - Update ECU

85.87.21

1.0

42

LR091126

https://topix.landrover.jlrext.com/topix/content/document/view?id=949249

3/18

1/7/2019

LTB01009NAS7 - InControl® Touch Pro™ Features May Not Function As Expected | TOPIx

NOTE:
Normal Warranty procedures apply.

S E R V I C E I N F O R M AT I O N - V E H I C L E S W I T H S I N G L E - S C R E E N S Y S T E M :

CAUTION:
Due to this important and irreversible change to the way the customer directly interacts
with their vehicle, retailers must inform the customer of this change to their vehicle before
performing the following update. Perform the update ONLY after the customer is informed
and in agreement.

NOTE:
The look and feel of the single-screen InControl® Touch Pro™ system will, if not already
updated with Phase 4 '18B' software, change to match that of the InControl® Touch Pro
Duo™ system. When this software update is finished, it CANNOT be reversed. Refer to the
latest InControl Touch Pro Release Notes on TOPIx for more information.

https://topix.landrover.jlrext.com/topix/content/document/view?id=949249

4/18

1/7/2019
1

LTB01009NAS7 - InControl® Touch Pro™ Features May Not Function As Expected | TOPIx



Vehicles with Single-Screen System current 4-tile home screen:
A - Media
B - Climate
C - Phone
D - Navigation

https://topix.landrover.jlrext.com/topix/content/document/view?id=949249

5/18

1/7/2019
2

LTB01009NAS7 - InControl® Touch Pro™ Features May Not Function As Expected | TOPIx



Vehicles with Single-Screen System updated 3-tile home screen:
A - Navigation
B - Media
C - Phone

DIAGNOSTIC PROCEDURE:

CAUTIONS:
Make sure that the Jaguar Land Rover-approved diagnostic equipment is connected to the
internet every 24 hours.
This software update is split into 2 separate procedures and, depending on the software level,
it may first require an update to the Gateway Control Module (GWM).

https://topix.landrover.jlrext.com/topix/content/document/view?id=949249

6/18

1/7/2019

LTB01009NAS7 - InControl® Touch Pro™ Features May Not Function As Expected | TOPIx

Battery support unit: it is extremely critical to use a battery support unit and have a vehicle
with a battery that has a good state of health to start. The battery support unit must also be in
proper working condition to be able to supply 13v consistently. If the voltage is compromised
during the installation of software, the Infotainment Master Controller (IMC) may switch off.
The software transfer process can take some time, please be patient. The vehicle ignition will
switch OFF during this transfer which is normal -- do not touch the engine START/STOP
button unless instructed to do so.
Before starting, make sure that the Infotainment screens display the 'Home' screen with the
ignition switched ON. If not (the display screens show the Land Rover logo or the front screen
is blank), lock the vehicle and leave for 5 minutes, then unlock the vehicle. Switch the ignition
ON and view the Infotainment screens again.
It is extremely critical NOT to disturb the Data Link Connector (DLC) connection. Any
interruption in connection between VCI and the DLC connection will result in a failure and may
not be recoverable.
Remove all customer Universal Serial Bus (USB) devices from any of the vehicle front and rear
USB ports (as applicable) before connecting the Jaguar Land Rover-approved diagnostic
equipment and commencing with the software update. After successfully performing the
update and after disconnecting the Jaguar Land Rover-approved diagnostic equipment,
connect the customer USB devices back to their original location.

NOTES:
After the Gateway Control Module (GWM) programming occurs, a functional CAN reset is
sent to the vehicle. The very next step in the process then begins to run Variant Configuration
to the Infotainment Master Controller (IMC). If the Technician is too fast and is pressing green
‘tick’ (✓) boxes to push the process along, the Variant Configuration process will fail as the
IMC is not fully booted. Each time the Technician is instructed to turn the ignition ON they
should follow the diagnostic system prompts. The IMC in general takes 90 seconds for full
operation. A good point is pressing the 'Audio' button and then pressing the 'Source' button.
When the IMC is booted, all available sources will be displayed on the Source Selection
screen. At this time the 'continue' button can now be pressed.
If a failure occurs when the retry is attempted, the technician must switch the ignition back
ON and wait a minimum 90 seconds until the Infotainment Master Controller (IMC) is booted
https://topix.landrover.jlrext.com/topix/content/document/view?id=949249

7/18

1/7/2019

LTB01009NAS7 - InControl® Touch Pro™ Features May Not Function As Expected | TOPIx

up.
This action will result in the navigation ETA share contacts being deleted from the system.
Inform customers that any contacts previously stored in the navigation system (not phone
contacts) will need to be re-entered upon completion.
1

2

Connect the Jaguar Land Rover-approved battery power supply to the vehicle startup battery.

CAUTION:
The Jaguar Land Rover-approved diagnostic equipment must be loaded with
SDD155.03 Software Management Pack v308, InControl® Touch Pro™ Software 005.07
[or later], and the Vehicle Communication Interface (VCI) must be on the latest level as
per VCI Update Instructions (available on TOPIx). If a DA VCI device is used for the
update, it MUST be on a firmware level of 63 or later.
Connect the Jaguar Land Rover-approved diagnostic equipment to the vehicle and begin a
new session.

3

4

Follow all on-screen instructions.

CAUTIONS:
At the start of this process, the Jaguar Land Rover-approved diagnostic equipment
will transfer a large number of files to the Jaguar Land Rover-approved USB memory
device. These will then be transferred to the vehicle.
The Jaguar Land Rover-approved diagnostic equipment may prompt ‘No Update
Required’ in the software resolution screen; however, this software does require
updating; select the green ‘tick’ (✓) to continue the download.
NOTES:
If the Jaguar Land Rover-approved diagnostic equipment states that the InControl®
Touch Pro™ system is already at the latest required software level, exit the
application and go to Step 10.

https://topix.landrover.jlrext.com/topix/content/document/view?id=949249

8/18

1/7/2019

LTB01009NAS7 - InControl® Touch Pro™ Features May Not Function As Expected | TOPIx

The infotainment screen display will go blank or change color during this update. This
is normal behavior and is to be expected when the InControl® Touch Pro™ control
module software is being updated.
If the hyperlink is not available:
1 Select the Diagnosis Session Type.
2 Select Electrical - Information and entertainment system - Entertainment system.
3 Run and close the Datalogger tool to reveal the 'Extras' tab.
4 Select the Extras tab.
5 From 'Recommendations', run the Configure existing module - InControl Touch Pro
application.
5

NOTES:
This application will begin and the InControl® Touch Pro™ Health Check will display
on-screen. The InControl® Touch Pro™ Health Check will make sure that all
conditions are correct before the software update can begin. In the event of a failure
condition being identified by the InControl® Touch Pro™ Health Check, follow the
on-screen instructions to rectify the failure condition and then retry the application.
The application will not continue until all conditions are correct; all InControl® Touch
Pro™ Health Check failure conditions MUST be rectified.
When the Jaguar Land Rover-approved diagnostic equipment is formatting the
Jaguar Land Rover-approved Universal Serial Bus (USB) memory device and copying
over the software update package to the USB memory device, the diagnostic
equipment will finish and advise the technician to install the USB memory device into
the vehicle’s socket. The vehicle’s ignition must be ON, and the Infotainment Master
Controller (IMC) must be ON and fully booted this process can take up to 90 seconds.
Follow all on-screen instructions until prompted to insert the Jaguar Land Rover-approved
USB memory device into the Jaguar Land Rover-approved diagnostic equipment. Do as
instructed before proceeding.

6

NOTE:

https://topix.landrover.jlrext.com/topix/content/document/view?id=949249

9/18

1/7/2019

LTB01009NAS7 - InControl® Touch Pro™ Features May Not Function As Expected | TOPIx

Make sure the vehicle ignition is ON. Press the engine START/STOP button to switch it
ON if necessary.
Follow all on-screen instructions until prompted to transfer the Jaguar Land Rover-approved
USB memory device from the Jaguar Land Rover-approved diagnostic equipment to the
vehicle as instructed.
7

Transfer the Jaguar Land Rover-approved USB memory device into the vehicle before
proceeding on the Jaguar Land Rover-approved diagnostic equipment.

8

Follow all on-screen instructions until the application prompts 'Remove the Jaguar Land Rover
approved USB memory device from the vehicle'.
If the diagnostic equipment displays an error, refer to the TROUBLESHOOTING
section below and perform the relevant action to finish the update.

9

NOTE:
Make sure the vehicle ignition is ON. Press the engine START/STOP button to switch it
ON if necessary.
Follow all on-screen instructions until the application finishes successfully.

10

CAUTION:
At the start of this process, the Jaguar Land Rover-approved diagnostic equipment will