NHTSA ID Number: 10153095
Manufacturer Communication Number: 23W1 rev 0828201
TSB/Document Date: 2019-02-19
Summary
Inlet Air Box Housing Snow Flap Replacement & Oxygen Sensor Inspection/Replacement - The snow flap in the inlet air box housing may remain partially to fully open. Should this occur, excess warm air could enter the air intake through the snow flap inlet. The oxygen sensor will be checked during this service and, if measured degradation tolerances are met, the sensor will be replaced. Revision Summary Updated work procedure.
Emissions Recall
Code: 23W1
REVISION
Subject
Release Date
Revision Summary
Important Repair
Information!
Affected Vehicles
Inlet Air Box Housing Snow Flap Replacement & Oxygen Sensor Inspection/Replacement
August 28, 2017
Updated work procedure.
CAMPAIGN 23W1 MUST BE COMPLETED BEFORE BEGINNING THE 23U7 CAMPAIGN!
Over the next few weeks there will be updates made to ODIS and the campaign circular.
Do not retain any hard copies of campaign circulars – only refer to the electronic copies
posted to Elsa and ServiceNet.
U.S.A. :
2010-2013 MY Audi
A3 2.0L TDI Engine Vehicles (Generation 1)
Check Campaigns/Actions screen in Elsa on the day of repair to verify that a VIN qualifies for repair under this
action. Elsa is the only valid campaign inquiry & verification source.
Problem Description
Campaign status must show “open.”
If Elsa shows other open action(s), inform your customer so that the work can also be completed at
the same time the vehicle is in the workshop for this campaign.
The snow flap in the inlet air box housing may remain partially to fully open. Should this occur,
excess warm air could enter the air intake through the snow flap inlet.
The oxygen sensor will be checked during this service and, if measured degradation
tolerances are met, the sensor will be replaced.
Corrective Action
Install an improved inlet air box housing snow flap and, if measured degradation tolerances are
met, replace the oxygen sensor.
Parts Information
03L906262B (O2 Sensor) - Please contact the Parts Specialists via phone (800-767-6552,
option#2), email (VWoAPartsSpecialists@audi
.com) or chat with the VIN to order.
3C0129594A (Snow Flap) - Parts will be allocated prior to owner notification. If allocated parts
have been used and your dealership is at the weekly Upper Order Limit, please submit the
backordered sales document number to upperorderlimits@audi
.com to have additional parts
released.
G052172M2 (Special Anti-Friction Agent) – Each can of Special Anti-Friction Agent is
intended to service 100 Snow Flap installations. If allocated parts have been used and your
dealership is at the weekly Upper Order Limit, please submit the backordered sales document
number to upperorderlimits@audi
.com to have additional parts released.
Code Visibility
On or about August 11, 2017, affected vehicles were listed on the Inventory Vehicle Open
Campaign Action report under My Dealership Reports (found on www.accessaudi.com & OMD
Web). A list was not posted for dealers who did not have any affected vehicles.
On or about August 11, 2017, this campaign code showed open on affected vehicles in Elsa.
On or about August 11, 2017, affected vehicles were identified with this campaign code in the
VIN Lookup tool at www.audiusa.com.
Owner Notification
Owner notification took place in August 2017. Owner letter examples are included in this bulletin
for your reference.
Emissions Campaigns
Requirements
(CALIFORNIA ONLY)
The California Air Resources Board and the Department of Motor Vehicles (DMV) require
emissions-related campaigns to be completed prior to vehicle registration renewal. When
campaign work is done you must provide the owner with a signed “Vehicle Emission Recall –
The repair information in this document is intended for use only by skilled technicians who have the proper tools, equipment and training to correctly and safely maintain your vehicle. These
procedures are not intended to be attempted by “do-it-yourselfers,” and you should not assume this document applies to your vehicle, or that your vehicle has the condition described. To
determine whether this information applies, contact an authorized Audi
dealer. 2017 Audi
of America, Inc. All Rights Reserved.
August 2017
23W1 Page 1 of 14
Proof of Correction” certificate (RC EMISCAVWAU). Order certificates online via the
Compliance Label Ordering portal at www.accessaudi.com.
Additional Information
Please alert everyone in your dealership about this action, including Sales, Service, Parts
and Accounting personnel. Contact Warranty if you have any questions.
Dealers must ensure that every affected inventory vehicle has this campaign completed before
delivery to consumers.
Fill out and affix Campaign Completion Label (CAMP 010 000) after work is complete.
Labels can be ordered at no cost via the Compliance Label Ordering portal at
www.accessaudi.com.
The information in this document is intended for use only by skilled technicians who have the proper tools, equipment and training to correctly and safely maintain your vehicle. These procedures
are not intended to be attempted by “do-it-yourselfers,” and you should not assume this document applies to your vehicle, or that your vehicle has the condition described. To determine whether
this information applies, contact an authorized Volkswagen
dealer. 2016 Volkswagen
Group of America, Inc. All Rights Reserved.
August 2017
SAGA/WIN Page 2 of 14
Claim Entry Instructions
After campaign has been completed, enter claim as soon as possible to help prevent work from being duplicated
elsewhere. Attach the Elsa screen print showing action open on the day of repair to the repair order.
If customer refused campaign work:
U.S. dealers: Submit the request through Audi
Warranty Online under the Campaigns/Update option.
Service Number
Damage Code
Parts Vendor Code
Claim Type
23W1
0099
002
Sold vehicle: 7 10
Unsold vehicle: 7 90
Causal Indicator
Vehicle Wash/Loaner
Criteria I.D.
Mark Snow Flap as causal part*
Do not claim wash/loaner under this action
8P
Install new Snow Flap
Labor operation:
Quantity
1.00
0.01
2325 25 99
30 T.U.
Part Number
3C0129594A
G 052172M2
Description
Snow Flap*
Special Anti-Friction Agent
-ANDCheck condition of Heated Oxygen Sensor (G39)
Labor operation:
0150 00 00
up to 30 T.U. per GFF log.
-AND IF NECESSARYReplace Heated Oxygen Sensor (G39)
Labor operation:
Quantity
1.00
2357 19 99
Part number
03L906262B
40 T.U.
Description
Heated Oxygen Sensor (G39)
The repair information in this document is intended for use only by skilled technicians who have the proper tools, equipment and training to correctly and safely maintain your vehicle. These
procedures are not intended to be attempted by “do-it-yourselfers,” and you should not assume this document applies to your vehicle, or that your vehicle has the condition described. To
determine whether this information applies, contact an authorized Audi
dealer. 2017 Audi
of America, Inc. All Rights Reserved.
August 2017
23W1 Page 3 of 14
Customer Letter Example (USA only)
This notice applies to your vehicle:
Subject:
Emissions Recall 23W1 – Inlet Air Box Housing Snow Flap
2010-2013 MY Audi
A3 2.0L TDI Engine Vehicles (Generation 1)
Dear Audi
Owner,
As part of Audi
’s ongoing commitment to our environment, and in cooperation with the United States Environmental
Protection Agency and the California Air Resources Board, we are informing you of our decision to conduct an emissions
recall on certain 2010-2013 MY Audi
A3 2.0L TDI engine vehicles (Generation I). Our records show that you are the
owner of a vehicle affected by this action.
What is the issue?
The snow flap in the inlet air box housing may remain partially to fully open. Should
this occur, excess warm air could enter the air intake through the snow flap inlet.
The oxygen sensor will be checked during this service and, if measured degradation
tolerances are met, the sensor will be replaced.
What will we do?
Your authorized Audi
dealer will Install an improved inlet air box housing snow flap and,
if measured degradation tolerances are met, replace the oxygen sensor. This work will
take about an hour to complete and will be performed for you free of charge. Please
keep in mind that your dealer may need additional time for the preparation of the repair,
as well as to accommodate their daily workshop schedule.
What should you do?
In order to limit any possible inconvenience, please contact your authorized Audi
dealer
as soon as possible to schedule this service. For your convenience, you can also visit
www.audiusa.com and click on the “Find a Dealer” link to locate a dealer near you and
schedule this service.
Lease vehicles and
address changes
If you are the lessor and registered owner of the vehicle identified in this action, please
forward this letter immediately via first-class mail to the lessee within ten (10) days of
receipt. If you have changed your address or sold the vehicle, please fill out the
enclosed prepaid Owner Reply card and mail it to us so we can update our records.
Important information
for California Vehicle
Owners – California
Regulations
California regulations require that this campaign be completed prior to the time you
renew your vehicle registration. Therefore, please make sure that this campaign is
completed prior to the renewal of your vehicle registration, and that you furnish
proof of completion to the Department of Motor Vehicles (DMV) in the form of a copy of
the dealer’s repair order, including a signed “Proof of Correction” certificate. You obtain
this from your dealer after the campaign has been completed. Please retain the signed
“Proof of Correction Certificate” with your vehicle records. DO NOT MAIL THIS FORM
to the DMV, unless requested.
Reimbursement of
Expenses
If you have previously paid for repairs relating to the condition described in this letter, the
enclosed form explains how to request reimbursement. We would be pleased to review your
reimbursement request.
Can we assist you
further?
If your authorized Audi
dealer fails or is unable to complete this work free of charge within a
reasonable time, please contact Audi
Customer Experience at 1-800-253-2834 or via our
“Contact Us” page at www.audiusa.com.
Checking your vehicle
for open Recalls and
Service Campaigns
To check your vehicle’s eligibility for repair under this or any other recall/service campaign,
please visit the Recall/Service Campaign Lookup tool at www.audiusa.com and enter
your Vehicle Identification Number (VIN).
We apologize for any inconvenience this matter may cause; however we are taking this action to help ensure your vehicle
continues to meet and exceed your expectations. Thank you for your continued loyalty!
Sincerely,
Audi
Customer Protection
The repair information in this document is intended for use only by skilled technicians who have the proper tools, equipment and training to correctly and safely maintain your vehicle. These
procedures are not intended to be attempted by “do-it-yourselfers,” and you should not assume this document applies to your vehicle, or that your vehicle has the condition described. To
determine whether this information applies, contact an authorized Audi
dealer. 2017 Audi
of America, Inc. All Rights Reserved.
August 2017
23W1 Page 4 of 14
Campaign Work Procedure
23W1 Emissions Recall
ATTENTION!
Damages resulting from improper repair or failure to follow these work instructions are the dealer’s
responsibility and are not eligible for reimbursement under this action.
Required Parts
Quantity
Part Number
Part Description
1
3C0 129 594 A
Snow Flap
0.01
G 052 172 M2
Special Anti-Friction Agent
1 (if necessary)
03L 906 262 B
Heated Oxygen Sensor (G39)
Required Tools
•
VAS6150X – Diagnostic Tester (or equivalent)
•
VAS5054X – Remote Diagnosis Head (or equivalent)
•
3337 – Ring Wrench 7-piece set (or equivalent)
The repair information in this document is intended for use only by skilled technicians who have the proper tools, equipment and training to correctly and safely maintain your vehicle. These
procedures are not intended to be attempted by “do-it-yourselfers,” and you should not assume this document applies to your vehicle, or that your vehicle has the condition described. To
determine whether this information applies, contact an authorized Audi
dealer. 2017 Audi
of America, Inc. All Rights Reserved.
August 2017
23W1 Page 5 of 14
TIP
If Campaign Completion label is present,
no further work is required.
•
Enter the VIN in Elsa and proceed to the
“Campaign/Action” screen.
TIP
On the date of repair, print this screen and keep a copy
with the repair order.
•
Confirm the Campaign/Action is open .
If the status is closed, no further work is required.
- 💯【Conta.ct us for Support Directly】If you met any...
- 🔥🔥🔥【2026 AUTEL FLAGSHIP MK900BT MK900-BT, NEW...
- 🚗【3000+ ACTIVE TESTS (50➡3000+), SAME AS MS...
- 🚗【40+ HOT SERVICES FOR 150 MAKES (28+➡40+)】Full...
- 🚗【OE ALL SYSTEM DIAGNOSE, AUTO SCAN 2.0: SCAN LICENSE...
- 【TURN OFF CEL】 This AL319 car scanner diagnostic tool...
- 【EXTENSIVE APPLICATION】 Autel AL319 Compatible with...
- 【FOR END USER & DIYERS】 This error code reader AL319 is...
- 【USER-FRIENDLY DESIGN】 This OBD2 scanner and check...
- 【HIGH-QUALITY SERVICES】 12 months war.ranty from the...
Last update on 2026-06-23 / Affiliate links / Images from Amazon Product Advertising API
If the PDF is very large, it may not load in the preview below.
Some older TSBs had multiple PDFs — visit the NHTSA Website to view all PDFs.
If the TSB PDF does not show, download or view it on the NHTSA Website.
Click on the (+) Plus Sign
Then Click on Associated Document(s)
Search NHTSA Database for Recalls
Search NHTSA Database for Vehicle Investigations
View Latest Vehicle Investigations
Search NHTSA Database for Vehicle Complaints
View Latest Vehicle Complaints
TSB/Document ID: 23W1 rev 0828201
Replacement Service Bulletin Number:
MFR Communication Date: 2017-08-28
MFR Internal Campaign ID/Software Version:
Communication Type: Service Bulletin/Repair Instructions
NHTSA Components: ENGINE
MFR Component System:
MFR Component Subsystem:
Previous TSB | Next TSB |
- 2026 ALL-IN-ONE HEAVY DUTY TRUCK SCANNER – BUILT FOR DIESEL DIAGNOSTICS:The ANCEL X7HD PRO combines full-system diagnostics, bi-directional control, ECU coding, HDOBD/OBD2 functions, and 42+ reset services in one powerful heavy duty truck scanner. This diesel scan tool helps technicians, fleet owners, and repair shops diagnose problems faster, reduce downtime, and complete more repairs without switching between multiple truck diagnostic tools. Features a 10.1" Android tablet, Bluetooth & Wi-Fi, live data graphing, and 2 years of f-ree updates
- 42+ RESET FUNCTIONS – MORE THAN A BASIC TRUCK CODE READER:Perform essential service functions including forced DPF regeneration, injector coding, speed limiter adjustment, idle adjustment, oil reset, ABS reset, SRS reset, EPB reset, throttle reset, and suspension calibration. Designed for real truck maintenance and fleet service, this commercial truck diagnostic scanner helps reduce dealer visits, avoid unnecessary downtime, and handle more repair jobs with one diesel diagnostic tool
- ACTIVE TEST & ECU CODING – ADVANCED BIDIRECTIONAL SCAN TOOL FOR TRUCKS:Quickly locate faults by activating components and sending commands directly to vehicle systems. Test injectors, ABS, throttle, cooling systems, and other modules in real time without unnecessary disassembly. ECU coding and module matching help adapt replacement parts, restore factory settings, and reduce repeat repairs, making this semi truck scan tool ideal for advanced troubleshooting and daily shop work
- FULL-SYSTEM HDOBD/OBD2 DIAGNOSTICS – WIDE TRUCK & ENGINE COVERAGE:Read and clear codes, monitor live data, freeze frame, and diagnose engine, transmission, ABS, body, and other major systems. Compatible with Freightliner
, Kenworth
, Peterbilt
, Volvo
, Mack
, International
, and other commercial truck brands, plus Cummins
, Caterpillar
, Detroit, Paccar
, and Navistar
diesel engines. Also supports full OBD2/EOBD diagnostics for standard vehicles, making it a versatile truck obd2 scanner for mixed fleets and repair shops - PROFESSIONAL HARDWARE + RELIABLE SUPPORT – BUILT FOR DAILY SHOP USE:This professional diesel diagnostic computer features a 10.1" touchscreen, Android 10.0 system, 6000mAh battery, Bluetooth/Wi-Fi connectivity, and built-in front & rear cameras for documenting repairs and remote troubleshooting. Includes 2 years of fr-ee updates, 1-year w-arranty, and responsive technical support. Contact [email protected] before purchase to confirm compatibility and supported functions for your truck or diesel engine
- 【Built for Heavy Duty Diesel Diagnostics】Designed for SAE J1939 and J1708 compliant trucks, buses, and diesel-powered commercial vehicles. HD601 truck scanner diagnostic tool helps owner-operators, small fleets, mobile technicians, and independent repair shops quickly identify fault codes, view live data, and make informed repair decisions—saving time, reducing downtime, and avoiding unnecessary shop visits
- 【Full System Diagnostics+All HD OBD Modes】The New HD601 heavy duty truck scanner delivers full-system diagnostics on SAE J1939 and J1708-compliant commercial vehicles—digging into engine, transmission, ABS, fuel, every system that keeps your rig rolling. It supports all HD OBD modes, giving you live data, freeze frame, ECU info, vehicle info, emissions data tracking, plus code reading and clearing. Not just what broke, but why—so you fix it right the first time. Pinpoint issues faster, cut repair costs, and spend less time on the shoulder
- 【Wide Heavy-Duty Vehicle Coverage】Supports a wide range of heavy-duty vehicle manufacturers and systems, including Freightliner
, Kenworth
, Peterbilt
, Volvo
, International
, Detroit, Cummins
, Paccar
, Allison, Eaton
, Bendix
, Wabco, and more. Coverage varies by vehicle make, model, year, and system configuration. Contact our support team before purchase if compatibility verification is needed - 【Speaks Major Truck Protocol】The New HD601 diesel truck scanner is built for American-made trucks—and supports the heavy‑duty protocols you' re most likely to run into on the road: SAE J1939, J1708/J1587, ISO 15765‑4, ISO 14230‑4, ISO 9141‑2, J1850 PWM/VPW, ISO 27145‑4, and EURO‑6. For most trucks, model years, and systems, it speaks the language your vehicle understands. Just plug it in and start diagnosing—no guesswork, no gatekeeping. Note: vehicle functions and module availability may vary by manufacturer and model year
- 【Save Hundreds on Diagnostic Fees】Why pay $150–300 for someone to read your codes? With the New ANCEL heavy duty truck scanner, you can pull fault codes yourself—in minutes, without leaving the truck. One or two uses pays for the tool. After that, every diagnostic is money back in your pocket. Smart investment for owner-operators, techs, and small fleets. Read and clear stored fault codes in minutes. Active fault codes may require repairs before they can be cleared
- 【One Tool, Total Fleet Coverage: 6/9/16 Pin Ready】Featuring an integrated 16-pin OBD2 connector and professional-grade 6-pin & 9-pin adapters, this heavy duty truck scanner provides extensive support for J1939, J1708, J1587, ISO 14230-4, ISO 15765-4 and ISO 9141-2, ISO 27145-4 protocols. It offers reliable diagnostic coverage for major American diesel brands—including Cummins
, Paccar
, Caterpillar
, Detroit, and Freightliner
—making it a versatile semi truck scanner for managing any diverse fleet. - 【2 in 1 Diesel Code Reader & Advanced HD OBDII】Equipped with professional-grade diesel scanner capabilities, the HD301 diesel scanner features intuitive Read/Erase codes and turn off the "Check Engine" light. With the built-in DTC Lookup library, you can instantly access fault code definitions on-device without searching the internet. It also retrieves hundreds of essential live sensor data—such as coolant temperature, fuel pressure, and engine RPM—in a stable text format for precise and rapid troubleshooting. (Please note that the HD301 can not support DPF Regen.)
- 【Full System Truck Diagnostic】The FOXWELL HD301 heavy duty scan tool is engineered to deeply access and scan all available electronic control modules specifically for truck, including Engine, Transmission, ABS, SRS, Chassis, and Body Control. This professional truck scanner diagnostic tool allows you to identify issues across the entire vehicle, ensuring your rig stays in peak condition for the long haul.
- 【Versatile for most big Rigs: Commercial, Passenger & Beyond】Engineered for more than just trucks, this heavy duty scan tool offers extensive coverage for pickups, buses, trailers, and even marine vessels. From construction machinery (excavators, loaders) to agricultural equipment (tractors, harvesters), it provides a true all-in-one diagnostic solution.
- 【Plug-and-Play & No Subscription】Designed for the road! No WiFi, no batteries, and no complex App setup required. Simply plug it into your vehicle’s diagnostic port to start scanning immediately. Enjoy lifetime free software updates to keep your HD301 diesel truck scanner current with the latest vehicle models and features—without any hidden subscription fees—While overcoming language barriers with support for Spanish and English.
Last update on 2026-06-23 / Affiliate links / Images from Amazon Product Advertising API
This product presentation was made with AAWP plugin.




