Classification:

Reference:

Date:

EC13-015g

ITB13-044g

January 29, 2019

ALL MODEL YEAR 2012 AND NEWER INFINITI VEHICLES;
EVAP LEAK DTC P0442, P0455, P0456 INFORMATION
This bulletin has been amended. See Amendment History on the last page.
Please discard previous versions of this bulletin.

APPLIED VEHICLES:

All model year 2012 and newer Infiniti vehicles

SERVICE INFORMATION
Example
All model year 2012 and newer Infiniti vehicles have a warning indicator in
the instrument area to alert the driver of a loose fuel filler cap (see Figure 1
example).
Figure 1


If a vehicle displays a Loose Fuel Filler Cap warning light or message, the driver should safely stop the
vehicle and make sure the fuel filler cap is installed correctly.



Make sure the customer is informed of the proper fuel filler cap installation.



Customers should refer to their vehicle Owner’s Manual for specific details on the “LOOSE FUEL CAP”
warning system and fuel filler cap installation.

If a fuel filler cap is left loose for multiple trips, DTCs will be stored and the MIL will illuminate.


If one or more of these EVAP leak DTCs are stored (P0442, P0455, P0456), a loose fuel filler cap
may be the cause.



If P0442, P0455, and/or P0456 is found stored, begin vehicle EVAP system diagnosis using the
Flow Chart on the next page.
 A test drive is not part of the DTC confirmation or diagnostic procedures for these DTCs.
 Test-driving the vehicle for these DTCs will only waste time.
 The diagnostic procedure in this bulletin must be used for these DTCs for an effective repair.
NOTE: Any parts replaced under warranty for repair of these DTCs are on automatic parts return to
NNA for inspection. Any part found to be functional will cause a charge-back to the dealer.

Infiniti Bulletins are intended for use by qualified technicians, not 'do-it-yourselfers'. Qualified technicians are properly trained
individuals who have the equipment, tools, safety instruction, and know-how to do a job properly and safely. NOTE: If you believe that
a described condition may apply to a particular vehicle, DO NOT assume that it does. See your Infiniti retailer to determine if this
applies to your vehicle.
1/5

FLOW CHART
Were any of the following DTCs found
stored?
• P0442
No
• P0455
• P0456

This bulletin does
not apply

Yes
Connect CONSULT-III plus (C-III
plus) to the vehicle
NOTE: A “smoke” leak detection
machine may be used. Follow the
manufacturer’s operating
instructions.

1. Confirm fuel filler cap is secure
2. Connect essential tool
J-42909 (see page 3 or 4)
3. Using Active Test, close vent
control valve
4. Apply pressure using
J-42909 until bar graph reaches
about halfway
5. Monitor the bar graph for
10 minutes

Models without a service port, check
for purge control valve leak
(see page 4)

Bar graph remained stable and
purge control valve is not leaking?

•

NO EVAP LEAK detected
at this time

•

MIL ON due to fuel filler
cap not being properly
secured (loose)

•

Erase DTC(s)

•

Advise customer fuel filler
cap ALWAYS needs to be
properly secured

•

DO NOT REPLACE FUEL
FILLER CAP OR ANY
OTHER EVAP RELATED
PARTS

Yes

No

EVAP leak detected
This bulletin does not apply

• See CLAIMS
INFORMATION
on page 5

Refer to ASIST and the applicable
Electronic Service Manual
for further diagnosis

2/5

ITB13-044g

Models With a Service Port
(2017 and older, except QX30)

Connect essential tool J-42909
to the service port and perform
EVAP system leak check.
There is no need to perform a
separate leak check of the purge
control valve.

Figure 2
EVAP System Basic Operation


Fuel vapor flows from fuel tank into canister (light blue area)



Vapor flows from canister through purge control valve (red line)



Fresh air flows into canister (green line)

3/5

ITB13-044g

Models Without a Service Port
(2018 and Newer, and all QX30)

Disconnect the EVAP line at the
purge control valve.
Connect essential tool J-42909 to the
EVAP line and perform EVAP
system leak check.
Use special tool J-42909 to also
perform a separate leak check of the
purge control valve.

Figure 3
EVAP System Basic Operation


Fuel vapor flows from fuel tank into canister (light blue area)



Vapor flows from canister through purge control valve (red line)



Fresh air flows into canister (green line)

4/5

ITB13-044g

CLAIMS INFORMATION
Submit a Primary Part (PP) type line claim using the following claims coding:
DESCRIPTION
PFP
OP CODE
SYM
EVAP System Leak Test

(1)

FX47AA

ZE

DIA

FRT

32

0.4

(1) Refer to the electronic parts catalog and use the Fuel Cap part number (17251-xxxxx) as the primary failed
part.

AMENDMENT HISTORY
DATE

REFERENCE

DESCRIPTION

November 15, 2013

ITB13-044

Original bulletin published

September 16, 2014

ITB13-044a

Amended Applied Vehicles, Service Information, Claims
Information

May 29, 2015

ITB13-044b

Amended Applied Vehicles

February 4, 2016

ITB13-044c

Amended Applied Vehicles

August 4, 2016

ITB13-044d

Amended Applied Vehicles

March 30, 2017

ITB13-044e

Amended Applied Vehicles

August 15, 2018

ITB13-044f

Amended Applied Vehicles, Service Procedure

January 29, 2019

ITB13-044g

Amended Applied Vehicles

5/5

ITB13-044g