TIS Service Bulletin

Page 1 of 3

SI B07 02 18
Diagnosis

November 2018
Technical Service

STATUS OF FAULT CODES IN ISTA FOR G05/G15
MODEL
G05 (X5)

G15 (8 Series Coupe)

SITUATION
After programming it could be that some fault codes cannot be deleted even after a sleep cycle of the vehicle.

CAUSE
Some of these errors are erroneous faults, which can be ignored. Some of the faults are still under
investigation.
Refer to the table below which shows a list of fault codes, a short description and how to deal with it.

CORRECTION
Please see table for further information.

Fault Code

Fault Description

Correction

0x030215

FZD (Function Center Roof Module) loses
Sliding/tilt sunroof: No initialization
initialization when it is programmed.
due to invalid normalization
Perform service function in ISTA (part of
values
therapy plan) for S18A

0x031E31

RAM: Manipulation of Adjustment
Block detected

Please ignore – fault code won´t be
displayed with ISTA 4.15.2x

0x801C90

ZGM: OBD firewall not initialized

Fault code is set correctly - the OBD firewall
will only be initialized after PDI /
provisioning

0x8029CA

Still under investigation; most likely a
SMFA: Seat position not send due problem with the internal Bootloader Update
to missing or invalid calibration
of the seat modules (loss of initialization
data); Workaround: perform seat calibration

0x802A05

SMFA: Locking protection switchoff due to missing calibration

Still under investigation; most likely a
problem with the internal Bootloader Update
of the seat modules (loss of initialization
data); Workaround: perform seat calibration

0x802A29

Driver`s seat module, backrest
angle adjustment: restricted

Still under investigation; most likely a
problem with the internal Bootloader Update

https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/48... 12/3/2018

TIS Service Bulletin

Page 2 of 3

adjustment due to lack of
calibration

of the seat modules (loss of initialization
data); Workaround: perform seat calibration

0x802A2A

Driver`s seat module, headrest
height adjustment: restricted
adjustment due to lack of
calibration

Still under investigation; most likely a
problem with the internal Bootloader Update
of the seat modules (loss of initialization
data); Workaround: perform seat calibration

0x802BCA

SMBF: Seat position not sent due
to missing or invalid calibration

Still under investigation; most likely a
problem with the internal Bootloader Update
of the seat modules (loss of initialization
data); Workaround: perform seat calibration

0x802C05

SMBF: Locking protection switchoff due to missing calibration

Still under investigation; most likely a
problem with the internal Bootloader Update
of the seat modules (loss of initialization
data); Workaround: perform seat calibration

0x802C29

Front passenger seat module,
backrest angle adjustment:
restricted adjustment due to lack
of calibration

Still under investigation; most likely a
problem with the internal Bootloader Update
of the seat modules (loss of initialization
data); Workaround: perform seat calibration

0x802C2A

Front passenger seat module,
backrest height adjustment:
restricted adjustment due to lack
of calibration

Still under investigation; most likely a
problem with the internal Bootloader Update
of the seat modules (loss of initialization
data); Workaround: perform seat calibration

0x802C2C

SMBF: No preventive seat
adjustment due to missing
calibration

Still under investigation; most likely a
problem with the internal Bootloader Update
of the seat modules (loss of initialization
data); Workaround: perform seat calibration

0x8042A0

Windshield wiper (LIN): Coding
invalid

Problem with LIN startup; should be
possible to delete after sleep cycle; in some
cases, another coding of the BDC (Body
Domain Controller) is necessary

0xB7F8C5

CID hardware error: error in flash
data checksum

Please ignore – fault code won´t be
displayed with ISTA 4.15.2x

0xB7F8FB

HU-H: invalid certification block
list

This problem is caused by the IT backend
and can´t be fixed in the car; please ignore
OR create an IT ticket

0xCD9763

Message (request, rear axle
speed, 69.3.4) missing, receiver
DDE, transmitter DSC

Please ignore – fault code won´t be
displayed with ISTA 4.15.2x

0xCD9767

Message (request, front axle
speed, 69.3.4) missing, receiver
DDE, transmitter DSC

Please ignore – fault code won´t be
displayed with ISTA 4.15.2x

0xCD990B

FlexRay, message (request, rear
axle RPM, 69.3.4): Missing

Please ignore – fault code won´t be
displayed with ISTA 4.15.2x

0xCD990E

FlexRay, message (request, front
axle RPM, 69.3.4): Missing

Please ignore – fault code won´t be
displayed with ISTA 4.15.2x

https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/48... 12/3/2018

TIS Service Bulletin

Page 3 of 3

0xD90D54

NFC Reader, inside front:
Unexpected CAN user

Still under investigation; please ignore if
system is working properly

0xE10602

Instrument cluster: Ethernet: Poor
signal quality

Please ignore – fault code won´t be
displayed with ISTA 4.15.2x

0xE12C4D

Signal (roadway inclination,
0x163) invalid, transmitter DSC

Please ignore – fault code won´t be
displayed with ISTA 4.15.2x

[ Copyright ©2018 BMW of North America, Inc. ]

https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/48... 12/3/2018