T-SB-0010-18

Rev1

February 2, 2018

Transaxle Assembly and ECM (PCM) Software
Confirmation
Service
Category

Engine/Hybrid System

Section

Engine Control

Market USA

Applicability
YEAR(S)

MODEL(S)

2018

Camry

ADDITIONAL INFORMATION

REVISION NOTICE
November 15, 2018 Rev1:
 The Production Change Confirmation Procedure section has been updated.
Any previous printed versions of this bulletin should be discarded.

Introduction

When completing a transaxle assembly replacement, Engine Control Module (ECM) (SAE term:
Powertrain Control Module [PCM]) replacement, or ECM (PCM) reprogram, ensure the correct
ECM (PCM) software is matched with the transaxle assembly hardware. Some 2018 model year
Camry vehicles require different ECM (PCM) software based on the transaxle assembly hardware
installed in the vehicle.
NOTICE
Mismatched transaxle assembly hardware and ECM (PCM) software combinations may result
in a harsh shift or shift flare. If this occurs after the original repair, additional ECM (PCM)
replacement and reprogramming will be required. This additional ECM (PCM)
replacement/reprogramming is NOT covered under warranty.

Use the information in this Service Bulletin to confirm that the correct ECM (PCM) hardware and
software are used based on the transaxle assembly part number and serial number.

© 2018 Toyota Motor Sales, USA

Page 1 of 8

T-SB-0010-18

Rev1

February 2, 2018

Page 2 of 8

Transaxle Assembly and ECM (PCM) Software Confirmation
Warranty Information
OP CODE

DESCRIPTION

TIME

OFP

T1

T2

369011

Z Time Add-on to Transaxle Replacement
OP Code

0.3

30500-####0

TBD*

TBD*

NOTE
 For transaxle replacement: Claim should be submitted as a normal replacement of the transaxle. If the
ECM (PCM) software needs to be updated when replacing the transaxle, add 0.3 hours of “Z time” to
the transaxle replacement OP code.
 For ECM (PCM) reprogramming or replacement: This Service Bulletin is used for E CM (PCM) and
software selection; however, this does NOT incur additional warranty cost.
* Based on replacement phenomenon.

Parts Information
PART NUMBER
PREVIOUS

PART NAME

QTY

Authorized Modifications Labels

1

NEW

00451-00001-LB L
NOTE

Authorized Modifications Labels may be ordered in packages of 25 from the Materials
Distribution Center (MDC) through Dealer Daily – Parts – Dealer Support Materials Orders.

Required Tools & Equipment
REQUIRED EQUIPMENT

SUPPLIER

Techstream 2.0*
Techstream Lite

PART NUMBER

QTY

TS2UNIT
ADE

Techstream Lite (Green Cable)

TSLITEPDLR01
TSLP2DLR01

* Essential SST.

NOTE
 Only ONE of the Techstream units listed above is required.
 Software version 13.20.018 or later is required.
 Additional Techstream units may be ordered by calling Approved Dealer Equipment (ADE)
at 1-800-368-6787.
 Use Techstream or an approved J2534 interface to perform flash reprogramming updates. Visit
techinfo.toyota.com for more information regarding J2534 reprogramming.

© 2018 Toyota Motor Sales, USA

1

T-SB-0010-18

Rev1

February 2, 2018

Page 3 of 8

Transaxle Assembly and ECM (PCM) Software Confirmation
Required Tools & Equipment (continued)
SPECIAL SERVICE TOOLS (SST)

PART NUMBER

QTY

GR8 Battery Diagnostic Station*

00002-MCGR8

1

* Essential SST.

NOTE
Additional SSTs may be ordered by calling 1-800-933-8335.

Production Change Confirmation Procedure

For transaxle assembly replacement, go to Option 1 and use the part number on the transaxle
assembly AND Table 1 to confirm if the transaxle that was just installed is BEFORE or AFTER the
production change. This information will allow you to confirm, using the Calibration Information
table on page 6, if the vehicle has the correct, matching software for that transaxle.
If NOT replacing the transaxle and you would like to confirm that the software matches the
transaxle, go to Option 2 and use the serial number on the transaxle assembly to determine if the
transaxle was built BEFORE or AFTER the production change. This information will allow you to
confirm, using the Calibration Information table on page 6, if the vehicle has the correct, matching
software for that transaxle.
Option 1: Confirmation by Part Number

1. Determine if the vehicle has a transaxle assembly produced BEFORE or AFTER the
production change using the table below. Use the tenth digit of part number to judge BEFORE
or AFTER.
Table 1.
JUDGMENT

Before
After

PART NUMBER

PART NAME

30510-####0-84

Reman ATM

30500-####0

Transaxle, Assy

30510-####1-84

Reman ATM

30500-####1

Transaxle, Assy

2. Using the judgment from Table 1, refer to the Engine Control Computer (ECM/PCM)
Replacement Information and Calibration Information sections.
NOTE
If unable to determine the part number, continue to Option 2: Confirmation by Production Change
Effective Serial Number.

© 2018 Toyota Motor Sales, USA

T-SB-0010-18

Rev1

February 2, 2018

Page 4 of 8

Transaxle Assembly and ECM (PCM) Software Confirmation
Production Change Confirmation Procedure (continued)
Option 2: Confirmation by Production Change Effective Serial Number

1. Locate the transaxle serial number, found on the sticker located on the transaxle assembly
side cover or on the engraved location as shown. Serial number decoders are also
provided below.
Figure 1. Serial Number Sticker and Engraved Serial Number Location

1

2

1

Serial Num ber Sticker

2

Engraved Serial Number Location

Figure 2. AW Plant Serial Number Decoder

Figure 3. Kinuura Plant Serial Number Decoder

© 2018 Toyota Motor Sales, USA

T-SB-0010-18

Rev1

February 2, 2018

Page 5 of 8

Transaxle Assembly and ECM (PCM) Software Confirmation
Production Change Confirmation Procedure (continued)
Option 2: Confirmation by Production Change Effective Serial Number (continued)
Figure 4. TMMWV Plant Serial Number Decoder

2. Use the table below to determine if the vehicle has a transaxle assembly produced BEFORE
or AFTER the production change.
Table 2.
PLANT

PRODUCTION CHANGE EFFECTIVE SERIAL NUMBER

AW

7B617J24024
7A617M22012

Kinuura

UB####17919Y206
UA####17C21Y 206

TMMWV 1

B1A17K10678

TMMWV 2

B2A17K10697

AWTEC (REMAN)

17AZ0612P

3. Using the information from Table 2, refer to the Engine Control Computer (ECM/PCM)
Replacement Information and Calibration Information sections.

© 2018 Toyota Motor Sales, USA

T-SB-0010-18

Rev1

February 2, 2018

Page 6 of 8

Transaxle Assembly and ECM (PCM) Software Confirmation
Engine Control Computer (ECM/PCM) Replacement Information

Based on the judgment of the transaxle serial number, use the table below to ensure that the correct
ECM (PCM) is ordered for ANY replacements being performed.
JUDGMENT

VEHICLE PLANT

PART NUMBER

ENGINE

Tsutsumi
4L
Before
TMMK
V6

PREVIOUS

NEW

89661-33T40
89661-33T41
89661-33T42

89661-33T30

89661-06X50
89661-06X51
89661-06X52

89661-06Y00

89661-06Y20

Tsutsumi
4L
After
TMMK
V6

89661-33T40
89661-33T41
89661-33T42

89661-33T43

89661-06X50
89661-06X51
89661-06X52

89661-06X53

89661-06Y20

89661-0X170

Calibration Information

Based on the judgment of the transaxle serial number, use the table below to ensure the correct
calibration file is used for ANY ECM (PCM) reprogramming procedures being performed.
JUDGMENT

ENGINE

ECU TYPE

NEW

Main

8966333P4000
8966333P4100
8966333P4200
8966333P4300

8966333P3000

Sub

896653379000
896653379100

896653356000

Main

8966306L5000

Sub

896650644000

Main

8966333P4000
8966333P4100
8966333P4200
8966333P4300

8966333P4400

Sub

896653379000
896653379100

896653379200

Main

8966306L5000

8966306L4000

Sub

896650644000

896650654000

A25A-FKS
Before

2GR-FKS

A25A-FKS
After

2GR-FKS

CALIBRATION ID
PREVIOUS

© 2018 Toyota Motor Sales, USA

–

T-SB-0010-18

Rev1

February 2, 2018

Page 7 of 8

Transaxle Assembly and ECM (PCM) Software Confirmation
Repair Procedure

1. Does the ECM (PCM) need to be reprogrammed?
 YES — Continue to step 2.


NO — This bulletin does NOT apply. Continue diagnosis using the applicable
Repair Manual.

2. Check for the Authorized Modifications Label affixed to the vehicle in the applicable location
shown below.
Is the calibration ID listed the latest ECM (PCM) calibration?
 YES — This bulletin does NOT apply. Continue diagnosis using the applicable
Repair Manual.
 NO — Continue to step 3.
Figure 5. Location of Authorized Modifications Label for 2018 Camry

TOYOTA MOTOR CORPORATION
A UTHORIZE D

M OD IF IC A TIONS

THE FOLLOWING MODIFICATIONS HAVE BEEN MADE:
1
2

THESE MODIFICATIONS HAVE BEEN APPROVED
AS APPROPRIATE BY EPA AND CARB
3

DEALER CODE:
CHANGE AUTHORITY:

4

DATE:

5

1

Replacement ECM (PCM) Part Number
(e.g., 89661-33T30)

4

Date Com pleted

2

New Calibration ID (e.g., 8966333P3000)

5

This SB Num ber

3

Dealer Code

© 2018 Toyota Motor Sales, USA

T-SB-0010-18

Rev1

February 2, 2018

Page 8 of 8

Transaxle Assembly and ECM (PCM) Software Confirmation
Repair Procedure (continued)

3. Flash reprogram the ECM (PCM).
NOTE
 The GR8 Battery Diagnostic Station MUST be used in Power Supply Mode to maintain battery
voltage at 13.5V while flash reprogramming the vehicle.
 For details on how to use the GR8 Battery Diagnostic Station, refer to the
GR8 Instruction Manual located at TIS – Diagnostics – Tools & Equipment – Battery Diagnostics.

Follow the procedures outlined in Service Bulletin No. T-SB-0134-16 Techstream ECU Flash
Reprogramming Procedure, and flash the ECM (PCM) with the NEW calibration file update.

4. Prepare and install the Authorized Modifications Label.
A. Using a permanent marker, enter the following information on the label:
 ECM (PCM) part number [Refer to the Parts Information section for the NEW
PART NUMBER]
 Calibration ID [Refer to the Calibration Information section for the
NEW CALIBRATION ID]
 Dealer Code
 Repair Date
 Change Authority [This bulletin number]
B. Affix the Authorized Modifications Label to the vehicle at the location shown in
Figure 5. The Authorized Modifications Label is available through the MDC,
P/N 00451-00001-LBL.

5. Test-drive the vehicle to confirm proper vehicle operation.

© 2018 Toyota Motor Sales, USA