Page 1 of 3

SI M12 06 15
Engine Electrical Systems

July 2015
Technical Service

This Service Information bulletin supersedes SI M12 06 15 dated June 2015.
designates changes to this revision
SUBJECT

Engine Power Reduction with “Clutch Damaged” Faults Stored
MODEL

F55 (Cooper, Cooper S 4-door Hardtop)
F56 (Cooper, Cooper S 2-door Hardtop)
Produced to

6/26/2015

With the B38M, B46M, and B48M engines
SITUATION

A drivetrain malfunction check control message is displayed, prompting the customer to contact the dealer for
a service visit.
The vehicle drives normally, but fault(s) for a damaged clutch are stored in the DME.
• 1D3101 - Clutch: Damaged, transmittable torque too low
• 1D3201 - Clutch: Severely damaged, transmittable torque too low
CAUSE

1. The DME software diagnostic for detecting excessive clutch slip is too sensitive.
2. The clutch is damaged.
PROCEDURE

Perform a test drive with a few hard accelerations in 2nd and 4th gear.
If the engine speed increases smoothly without any indication of the clutch slipping, the faults are erroneous
and the clutch is not damaged. Do not replace any parts!
If the engine speed jumps or increases quickly without engine power being applied, indicating a slipping
clutch, replace the clutch following the ISTA repair instructions.
Program the vehicle using the latest version of ISTA/P (
F55, F56

3.56.2 or higher).

Target Integration level: F056-15-07-501 or higher

Note that ISTA/P will automatically reprogram and code all programmable control modules that do not have
the latest software.
For information on programming and coding with ISTA/P, refer to CenterNet / Aftersales Portal / Service /
Workshop Technology / Vehicle Programming.
Always connect a MINI approved battery charger/power supply (SI M04 08 09).

https://www.minitis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/248...

8/6/2015

Page 2 of 3

WARRANTY INFORMATION

Covered under the terms of the MINI New Passenger Car Limited Warranty.
Covered under the terms of the MINI NEXT Certified Pre-Owned Limited Warranty (excluding the clutch
discs and assembly).
Defect Code:

10 42 31 59 00

Labor Operation:

Labor Allowance:

Description:

Refer to KSD2

Performing “vehicle
test” (with vehicle
diagnosis system –
checking faults)

Refer to KSD2

Connect an approved
battery charger/power
supply (indicated in
KSD2 as Charging
battery)

Work time (WT)

Performing vehicle
diagnosis (including
the test drive)

Refer to KSD2

Programming/encoding
control unit(s)

00 00 006

And:

61 21 528

And, as necessary:
61 00 006
And:
61 00 730

If you are using a Main labor code for another repair, use the Plus code labor operation 00 00 556 instead.
Refer to KSD2 for the corresponding flat rate unit (FRU) allowances.
Work time labor operation code 61 00 006 is not considered a Main labor operation. However, it does require
an individual punch time and an explanation on the repair order and claim comments.
Vehicle Programming and Encoding
If a control module or component was working properly and/or had no related faults stored prior to vehicle
programming and it fails to program correctly or requires initialization, this additional work must be claimed
with separate labor operations (refer to KSD2) under the defect code listed above.
Repairs to control modules and components with pre-existing conditions are not eligible to be claimed under
the defect code listed in this bulletin.
Other Repairs
If performing ISTA diagnostics, related test plans, and other diagnosis results in other eligible and covered
work, claim this work with the applicable defect code and labor operations listed in KSD2.

https://www.minitis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/248...

8/6/2015

Page 3 of 3

Note: The clutch disc and assembly are covered under the terms of the MINI New Passenger Car Limited
Warranty for defects in material or workmanship.
[ Copyright ©2015 BMW of North America, Inc. ]

https://www.minitis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/248...

8/6/2015